And so it begins.... (My adventures into Alox!)
-
If you remove the can opening part of the can opener (it sounds kind of silly, I know) , is the remaining driver a good 2D Philips? How does it compare to the 3D Philips?
-
@Sakpan74Gr said:
If you remove the can opening part of the can opener (it sounds kind of silly, I know) , is the remaining driver a good 2D Philips? How does it compare to the 3D Philips?Depends on the grinding job you do. ;)
I've found it to be a passable driver for both philips and flat. It definitely improves the reach compared to leaving the blade on.
Compared to the dedicated inline philips, it's not as strong, otherwise, it depends on how much you want to use it. For lots of use on stubborn screws, 3d all the way.
-
If you add serrations on the pen knife blade, will it still be able to cut paper smoothly? I am asking because some serrated blades rip it instead of cutting it.
-
Is it easy for a customer of yours to take apart and put back together your SAKs? If yes then perhaps you could provide different length screws, so that we could choose which tools to carry, a modular SAK!
-
Usually his customs use torx screws and barrel pivots. It's not just the length of the screws but the length of the pivot barrels and the diameter of the hole in the tools. You would need to have a variety of tools prepped and an appropriate length set of pivots for each configuration. Other than that, it should work. You might need some special pivots once you start to get over 4 layers or so.
-
@Sakpan74Gr said:
Is it easy for a customer of yours to take apart and put back together your SAKs? If yes then perhaps you could provide different length screws, so that we could choose which tools to carry, a modular SAK!No not easy but people do take them apart. Up to 3 layes is doable but beyond that a vice is needed to compress the springs. It not like a folder where scales lift off. These springs provide significant force which must be resisted to snap on the scale.
-
I've used a well padded set of vise grips to compress the springs on my syph mod. I've taken it apart and put it back together many times without too much trouble.
Sent from my iPhone using Tapatalk
-
Finally I could work again today. I had a weird chest pain, not heart attack bad though but annoying for a couple weeks. I finally ended up in emerg on Friday and found out I had walking pneumonia. Sure is nice to be able to breath fully again and get back to work!
Today I put together another Ti wrench mod. :D
This is custom Mod #500 !!





-
Glad to hear your ok and feeling better

-
Congrats on number 500!
Feel better... -
-
- :o

And to think we knew him when he took apart his first SAK.

-
Glad you're doing better and congrats on #500 buddy!
Sent from my SM-G920R4 using Tapatalk
-
Glad to hear you are A OK now! That is an awesome 500 mod!
-
@tattoosteve99 said:
Glad to hear your ok and feeling better
This. Be well, Bob!
-
Glad you're starting to feel better. Hopefully you'll be right as rain soon.
And congrats on number 500!
-
Holly crap, it is good to hear you're OK!!!
-
Congrats!

And go for the next 500!!!

-
The customer wanted some grip lines on this one and heat anodized scales. I just hit it with the torch for a bit to add some texture and it seems to have worked ok.




-
That looks Bada$$

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
for #500