Modded Mut Vs Signal
-
Nice job D- mac.
Sent from my SCH-I535 using Tapatalk
-
Nice Job DM

How did you go drilling it out? Looks like a better fit than mine too. Wish I could get my hands on one. How is the thickness? I wonder if I could get both in.
-
Yes, scissors would be great. I would welcome a city version of the Signal. Scissors instead of a saw, a measuring tape instead of the whistle, package opener instead of the can opener.
After that if possible a toothpick somewhere, a breath mint dispenser, extendable back scratcher that doubles up as magnet picker, removable pen/pencil, laser leveler, roll out solar panels to re-charge your electronic devices and a pull out space blanket for emergencies and impromptu picnics.

-
@rishardh said:
Yes, scissors would be great. I would welcome a city version of the Signal. Scissors instead of a saw, a measuring tape instead of the whistle, package opener instead of the can opener.After that if possible a toothpick somewhere, a breath mint dispenser, extendable back scratcher that doubles up as magnet picker, removable pen/pencil, laser leveler, roll out solar panels to re-charge your electronic devices and a pull out space blanket for emergencies and impromptu picnics.

On a serious note, more MTs need to include a package opener. One of the Dime's saving graces.
-
@rishardh said:
Yes, scissors would be great. I would welcome a city version of the Signal. Scissors instead of a saw, a measuring tape instead of the whistle, package opener instead of the can opener.After that if possible a toothpick somewhere, a breath mint dispenser, extendable back scratcher that doubles up as magnet picker, removable pen/pencil, laser leveler, roll out solar panels to re-charge your electronic devices and a pull out space blanket for emergencies and impromptu picnics.

While at it, could I add a TV, a fridge and a microwave on that?

@WoodsDuck said:
On a serious note, more MTs need to include a package opener. One of the Dime's saving graces.Make good sense, I think in spirit, MT is used to address 90% of our daily need, and I would rather to have a package opener than a serrated blade for seat beat cutting.
-
@TheDude said:
Nice Job DM
How did you go drilling it out? Looks like a better fit than mine too. Wish I could get my hands on one. How is the thickness? I wonder if I could get both in.
I'll take pictures when I try to do this mod with a Charge file. That is if the pivot hole is the same size or smaller. To big and I am stuffed...
Pete
-
@TheDude said:
Nice Job DM
How did you go drilling it out? Looks like a better fit than mine too. Wish I could get my hands on one. How is the thickness? I wonder if I could get both in.
Thanks! I used my drill press and cutting fluid to drill it out. It was a pretty slow process, and it was hard to keep the file from getting too hot.
I had to use a washer under it to bring it up high enough that the screw would be able to tighten it up. I don't think you'd be able to get two tools in that spot though.
Sent from my iPhone using Tapatalk

-
Not sure if it was done yet, here is a signal with Wingman scissors.


-
That looks awesome!!!
Sent from my SCH-I535 using Tapatalk
-
@Tooltime said:
Not sure if it was done yet, here is a signal with Wingman scissors.Tooltime - I see in your signature that you have a MUT too. Think the wingman scissors would fit in the MUT of you were to remove the plastic piece like others are doing? Are the pivots / tang shapes the same as in the Signal?
-
Monrogue, thanks
Tommywp, it is just like putting the wingman sissors on the wave. The hole in the spring piece is large enough but the hole in the sissors part needs to be opened up a bit, I used a tungsten carbide bit in my dermel for this(go slow). You also need to adjust the stop on the back of the sissors so that it will lock in place.
As for the mut, not sure what to do yet. Put a 3/32 punch on instead of the 1/8 so it fits my handguns. Saw a post about using the sissors from a card tool and putting it in the slot where one of the long bits go. I did fit an extra diamond file from a surge so it fit in the bit exchanger.
-

Hard to get a close up in focus. Both tools have had the belt clips removed.



-
Pietervn, here are the pictures of the mut and file. All i did was grind the end down enough to fit in the bit holder. It wobbles some side to side, but probably would be used off the tool anyway.


-
@Tooltime said:
Pietervn, here are the pictures of the mut and file. All i did was grind the end down enough to fit in the bit holder. It wobbles some side to side, but probably would be used off the tool anyway.G'Day Mate
Thanks for the pics. That is a very cool idea. I will try that over the weekend, it might very well solve my problem with not having a file, which I prefer to a saw for my EDC duties. I do have some extra old Surge saws and files that I kept when mine was replaced under warranty.
Enjoy the weekend,
Pete
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
