And so it begins.... (My adventures into Alox!)
-
Awesome!!
+1
Sent from my SM-G920R4 using Tapatalk
+2

+3. Nice tool layout
The ladies say this to me all the time.
Also, +4 Daddy likes.
A lot of the best tools but not to big and since I almost always have a dedicated folder the big SAK blade hardly gets used.
Hmm.
-
Ok, time for equiptment again. Im tired of waiting 24 hours for the tumbling to get the matte finish on the Ti, so I need a blasting cabinet...
Got this on the way. Amazon had them for a decent price. :D

Now I gotta get a compressor that can do 12 CFM at 80 PSI. I think those are going to be more than the blasting cab is, and it needs to be 220 volts so I'll have to run a line to the shop for that. I have a spare 220 breaker though so that shouldnt be a big deal, the ceiling is all open from teh breaker to the shop.
:D
-
New tools! Always exciting!
That blasting cabinet looks like a good piece of equipment and good luck with the compressor search. I started down a slippery slope when looking for one for my garage. Ingersoll Rand has some nice stuff, but I actually got an older Speedaire one for a fraction of the cost on Craigslist. I only wanted a 20 gallon tank but the quality of the motor, regardless of the tank size, is what you are really after. I ended up with a cast iron, double piston setup with changeable oil. Those oil-less ones are short lived and I don't believe would be up to your task. Then when you start looking at hoses and fittings, it starts to add up too. There are some pretty nice GoodYear hoses around unless you are hard lining it (although, i'd still be tempted by a section of hose so that it was at least a little moveable). Also, I've read that using a slightly larger line helps keep your pressure constant, so I went with 1/2" line with 3/8" fittings. For fittings, there are three standards that I ran across and I ended up getting mine all in Universal format so they will work with the other two main types, which won't work with each other.
This is like the compressor I was able to pick up for $150 in perfectly functioning order. 20 gal, 3 HP, 10 CFM @ 90 PSI. No problems so far in limited use:

But that is some of what I found when I was searching. You may have more experience on the subject already and I'm sure there are others around who can give you better guidance. Anything I've stated may actually be completely wrong so take it with a whole cup of salt.
Good luck with your search!
-
Ya the compressor Im not exactly sure what I need yet, but Im sending out some feelers for used ones right now. For the amount of blasting I'll be doing I dont need something too hard core that will be running all day or anything.
Im not at all concerned about noise, since it wont be on all the time either. Really its just going to be for glass bead blasting of Ti.
That one you got for 150 looks sweet. I hope I can find a deal somewhere. :D
-
I don't know how long it takes to do the blasting you need, but the longer the continuous use, the larger you want your tank. The compressor will only kick on when it needs to maintain the pressure in the tank. Those compact oil-less ones will run nearly the entire time and won't move the CFM you need. That, and they have a life of a year or so from what I have read. I bought mine for use with air tools when working on my Cherokee so I don't have quite the need of continuous blasting but I think that size would work for a few minutes at a time.
The deals are out there. Might have better luck after Christmas when people that got new compressors are selling their old ones. Then again, maybe there won't be a difference.
-
Cybertool 34 in Ti. :D
You can really see how much thickness is saved in the last couple of shot comparing it to my daily carry CT.
My blasting cab is due to arrive next week, so I better get shopping for a compressor. I found a place that sells all the media types in town. Aparently I can use a certain grit of sand to blade off the alox coating on alox scales and not have to use the nasty chemicals.









-
Nice Syph[emoji106]
Sent from my SM-G920R4 using Tapatalk
-
I really like that one!!!!

-
You can really see how much thickness is saved in the last couple of shot comparing it to my daily carry CT
I think it's funny that you EDC a stock SAK. The cobblers children have no shoes!
You should see the barber's haircut.
Didn't you say Mrs Syph has a stock SAK also? Shame.
-
You can really see how much thickness is saved in the last couple of shot comparing it to my daily carry CT
I think it's funny that you EDC a stock SAK. The cobblers children have no shoes!
It was one of the first SAKs I bought from Tim after I joined here, and its an old model with the thicker blade. Its been one of my favorites.
The problem with making pimped out SAKs is that once I have one done I never want to carry it as I could sell it and then have money to get more parts/supplies etc... so Ive got very few of my own mods here, just parts to make them?
You can really see how much thickness is saved in the last couple of shot comparing it to my daily carry CT
I think it's funny that you EDC a stock SAK. The cobblers children have no shoes!
You should see the barber's haircut.
Didn't you say Mrs Syph has a stock SAK also? Shame.
The Mrs has a wenger nail clipper model. But after I made that Ti 58 with the red garnet in it, she said she wanted one like that.
-
Soon I'll be having a Blast! :D well after I get it built...; buy a compressor... get it hooked up.. test media etc...
-
:ahhh
-
Is it ready yet?

-
What about now?

-
Maybe now? Hey what's taking so long?
-
Are we there yet!
-
Getting there. :D

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login