And so it begins.... (My adventures into Alox!)
-
Soon I'll be having a Blast! :D well after I get it built...; buy a compressor... get it hooked up.. test media etc...
-
:ahhh
-
Is it ready yet?

-
What about now?

-
Maybe now? Hey what's taking so long?
-
Are we there yet!
-
Getting there. :D

-
I think I'll call this one a knifeless companion SAK. Ive built 3 of these ones so far for people that either dont want a blade on there, or already carry a big folder, and they are a nice package of handy tools.


-
That is a really nice combination of tools and provides great utility!
-
Great tool layout! Very appealing to me personally.
Wish it was mine. :'( -
@Syph007 said:
I think I'll call this one a knifeless companion SAK. Ive built 3 of these ones so far for people that either dont want a blade on there, or already carry a big folder, and they are a nice package of handy tools.







That's a good tool set. Nice minimal and focused. (even though conceptually, I'm not a fan of that huge slab of plastic within the polished steel and tumbled Ti)
Sent from my Nexus 6 using Tapatalk
-
I think I'll call this one a knifeless companion SAK. Ive built 3 of these ones so far for people that either dont want a blade on there, or already carry a big folder, and they are a nice package of handy tools.








That's a good tool set. Nice minimal and focused. (even though conceptually, I'm not a fan of that huge slab of plastic within the polished steel and tumbled Ti)
Sent from my Nexus 6 using Tapatalk
Yeah Robert when is the Brass and Ti bit holders coming out?
-
That is a really nice combination of tools and provides great utility!
Yep, plus the Cyber driver is nicely centered.
Could you add a saw and file to this and keep the driver centered Robert? I bet adding them to the scissor side would keep it close.
Yep but pliers layer is only 0.020" wider than scissors so if you want the driver centered it might be best to put one on each side.
-
That is a really nice combination of tools and provides great utility!
Yep, plus the Cyber driver is nicely centered.
Could you add a saw and file to this and keep the driver centered Robert? I bet adding them to the scissor side would keep it close.
Yep but pliers layer is only 0.020" wider than scissors so if you want the driver centered it might be best to put one on each side.
You guys and your fancy measuring.
-
I have the same blasting cabinet, have used it for a few years now.
The trigger for the blasting gun failed quickly, so I gutted it. I have an adjustable air regulator mounted on the cabinet where the air supply goes in. This allows me to turn it on via the regulator and adjust the pressure, which varies the finish. I use "grit" which is cheaper than al oxide and seems to provide good results.
If you plan to remove paint or something that will produce larger pieces of waste I would suggest adding a layer of fine window screen to the underside of the mesh working plate. This will catch larger particles that will clog the fill tube. I also find it handy to have a catch can under the unit with a fine screen on the top so I can periodically strain out the media to get the large bits out. I strain the media before initial use as well. Might not be necessary if you use higher quality media. You can unclog the unit by forcing compressed air back through the media tube.
I also had to replace the light, as it failed, went with a more powerful dual bulb unit for more light. Also, make sure you install the thin clear plastic shields over the light and viewing windows. They are sacrificial, and will need to be swapped frequently. I also find it easier to use with less overhead light so if you can put it in a darker corner of the shop that helps. I also use a shop vac to evacuate the dust during use, that helps with visibility inside the cabinet as well. I plan to make a permanent dust extractor in a wooden cabinet. It will be quieter than the shop vac. There are some ideas online for building this with PVC pipe, etc.
I also plan to put a foot control for the air supply. I was going to get another trigger gun to replace the gutted one, but hand fatigue is an issue depending on how long you plan to use it. I have used my cabinet a lot, and with a few mods I feel it was well worth the price.
-
@jdindadell said:
I have the same blasting cabinet, have used it for a few years now.The trigger for the blasting gun failed quickly, so I gutted it. I have an adjustable air regulator mounted on the cabinet where the air supply goes in. This allows me to turn it on via the regulator and adjust the pressure, which varies the finish. I use "grit" which is cheaper than al oxide and seems to provide good results.
If you plan to remove paint or something that will produce larger pieces of waste I would suggest adding a layer of fine window screen to the underside of the mesh working plate. This will catch larger particles that will clog the fill tube. I also find it handy to have a catch can under the unit with a fine screen on the top so I can periodically strain out the media to get the large bits out. I strain the media before initial use as well. Might not be necessary if you use higher quality media. You can unclog the unit by forcing compressed air back through the media tube.
I also had to replace the light, as it failed, went with a more powerful dual bulb unit for more light. Also, make sure you install the thin clear plastic shields over the light and viewing windows. They are sacrificial, and will need to be swapped frequently. I also find it easier to use with less overhead light so if you can put it in a darker corner of the shop that helps. I also use a shop vac to evacuate the dust during use, that helps with visibility inside the cabinet as well. I plan to make a permanent dust extractor in a wooden cabinet. It will be quieter than the shop vac. There are some ideas online for building this with PVC pipe, etc.
I also plan to put a foot control for the air supply. I was going to get another trigger gun to replace the gutted one, but hand fatigue is an issue depending on how long you plan to use it. I have used my cabinet a lot, and with a few mods I feel it was well worth the price.
Good info thanks!
I figured Id have to DIY some things on this to get it the way I want, but its easier than starting from scratch.
This will only be used for glass bead surface finishing of Ti, so hopefully that should keep it pretty clean in there.
Im still shopping for a compressor. Could I not get by with a slightly lower CFM one and have a finer nozzle? That would keep the velocity high with the downside of blasting a smaller areas at one time.
-
My take on compressors is that more cfm and tank size is the way to go. Plus you need to look at duty cycle info for blasting, as you do use a lot of air. A larger tank can help with volume, but an undersized compressor will wear out quicker or just not be up to task.
-
Thank you @Syph007 [emoji106]. I have spent a pleasant day off work reading the entire thread, it shows a great deal of skill and craftsmanship and a real sense of pride in your work.
I like the "Gentleman" style of the Black with the brass accents, keep up the good work and I'm looking forward to seeing what 2016 has in store. Cheers.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login