jlwatso1's 31 Day SOG Super Power Badge Quest
-
DAY 3
Church Carry
I don't normally carry a full sized multi to church, but in the spirit of the challenge, I will be doing a little Powerlock Pocket Carry.


-
Cool pics!
-
DAY 4
Rise and shine! 4:20am comes early...
My brother-in-law saw my EDC gear that I belt carry and decided I needed a new belt for Christmas! I'm pretty pumped! This thing is SWEET!

(No offilliation with this company)



-
A little "GO JUICE" and some oatmeal bars for the road!

-
Cool belt and pouch and SOGs and coffee in the morning, awesome!
-
Those 5.11 belts are awesome! Super stiff. You could easily carry quite a few CCWs without It folding, let alone a MultiTool!
-
Started cutting copper this morning for a VRF (Variable Refrigerant Flow) setup. Deadmun (I have taken to calling him this as Dead Man Walking is a mouth full) just hung out until I started putting Armaflex (insulation) on the copper. I miss my outside opening blade... It takes a while to deploy the knife. The comfort grips hide the tools, so you can't tell which cover the knife is under. Both covers popped off before 8 am. I put one back on to differentiate which side the glad was under.

-
Used the needle nose to ream/woller out some copper and allow me to insert a copper line before braising. I like that it is more rounded than the head on Leatherman Surge. Haveing second thoughts about the nose job performed on my Surge. Forgot I used it for this. Oh yah, as I was reaming copper out, the other comfort grip/ tool cover slid up and was subsequently removed.

-
@jlwatso1 said:
Used the needle nose to ream/woller out some copper and allow me to insert a copper line before braising. I like that it is more rounded than the head on Leatherman Surge. Haveing second thoughts about the nose job performed on my Surge. Forgot I used it for this. Oh yah, as I was reaming copper out, the other comfort grip/ tool cover slid up and was subsequently removed.It's nice to see someone using their tool, mine's been doing minimal work these last couple of days. But how are those covers attached? They seem to come loose all the time!
-
I don't know if yours is different, but on my unmodified powerlock the knife blade and scissors are in the grip with the lettering.
-
Used the needle nose to ream/woller out some copper and allow me to insert a copper line before braising. I like that it is more rounded than the head on Leatherman Surge. Haveing second thoughts about the nose job performed on my Surge. Forgot I used it for this. Oh yah, as I was reaming copper out, the other comfort grip/ tool cover slid up and was subsequently removed.
It's nice to see someone using their tool, mine's been doing minimal work these last couple of days. But how are those covers attached? They seem to come loose all the time!
There are just some notches in the tool. I think I would have to pop rivet them on if I wanted to keep them on a rough as I am on this thing...
-
i had similar issues with my Powerlock. I just tossed the handle covers, they were more annoying than they were worth.
-
@sLaughterMed said:
i had similar issues with my Powerlock. I just tossed the handle covers, they were more annoying than they were worth.Same here!

-
So it looks like it is going to be a long month... I was looking at my Powerlock and saw that the clip/retainer is missing from the bit adapter! The only time I have used it was to see if some bits from my socket set would work on it to replace my car battery a couple days ago, but I didn't have the right adapter. Guess it must have come off then. I will send it in for warranty after the challenge is over.

-
Here's a pic

-
Just call them up. They should send you one.
-
Also, nice action shots!
-
@ducttapetech said:
Just call them up. They should send you one.Sweet! I'll have to try that today! It's my off day.
-
DAY 4
Not much to report today. Tuesdays are my day off. Sent an email to SOG's warranty department this morning to see if they could send me a new 1/4" bit driver or if I would have to send it in. No reply ret. Fabricated a new tool lock for my PT-540. Got it functional, but it still needs some cosmetic work. I may stamp my initials in it with some letter punches my folks got me for Christmas. Had to stop working on it because my daughter just woke up from her nap. Hopefully I will be able to duplicate it so they both look the same. Pics are on the Leatherman forum under Surge/ES4 Possible mod question. If anyone is interested.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login