And so it begins.... (My adventures into Alox!)
-
Monrogue asked that you send it to me Robert.
Something about not being able to handle it and he knows I am the man that can.
-
@Syph007 said:
I guess my adventures in alox have wound down, but Im happily adventuring in Ti instead. Its just do darn tough and strong I see why most knife makers love it.Here is a Monrogue model all done. :D






I love the look of the copper cross with the matte gray Ti...

Yeah, that's a damn nice Rogueneer right there. Excellent work my friend

Sent from my SM-G920R4 using Tapatalk
-
@MadPlumbarian said:
Nice job Syph, hey Monrogue I bet your like
now the worst part, downtime! lol
JRYup :)
Sent from my SM-G920R4 using Tapatalk
-
@HarleyXJGuy said:
Monrogue asked that you send it to me Robert.Something about not being able to handle it and he knows I am the man that can.
Hahahaaaa! I think not my dear Harley

Sent from my SM-G920R4 using Tapatalk
-
Another lovely job. Nice one.
-
Here is something a bit different. Just a two layer SAK but the customer wanted a keyring on there too. Normally that is in the blade layer, but since there is no blade layer I had to figure something else out.
I ended up milling some off the end of the pliers spring and then riveting the keyring piece on that. I used 2 rivets and I think its on there solid enough.
I suppose I could have hand cut a custom liner with the keyring build into that, but that felt like more work then this method... maybe it would have been similar though.

-
That's an interesting choice of tool loadout for a SAK.
Sent from my SM-G920R4 using Tapatalk
-
I'm jelly Monrogue!
:ahhh -
@Syph007 said:
Here is something a bit different. Just a two layer SAK but the customer wanted a keyring on there too. Normally that is in the blade layer, but since there is no blade layer I had to figure something else out.I ended up milling some off the end of the pliers spring and then riveting the keyring piece on that. I used 2 rivets and I think its on there solid enough.
Great work as always Syph in the "Adventures into Ti" thread - Amazing and ingenious approach to your build challenges once again.
Was the new KR originally from a liner or spring?I like the way you cut (milled) out a wee hole for the pliers pivot.
However if you had put the tools the other way round maybe that would not have been necessary?
Or even reversed the pliers - But I guess the spring would not work then?One general comment for everyone...
I love all these variations and mods - And obvioulsy the scales are something very special, different and new.
But it still amazes me that folk want such variations in the toolsets
I just think there are so many options with the catalogue models - Why not just go with one of those ???
I know you do Syph!! As does Def and many others here?And often with these variations - I think folk are missing out on tools
Eg this one - No blade or operners - I cannot imagine a SAK without those ???
Or the Rogueneer - No saw? - Why not take that too?? :o -
Here is something a bit different. Just a two layer SAK but the customer wanted a keyring on there too. Normally that is in the blade layer, but since there is no blade layer I had to figure something else out.
I ended up milling some off the end of the pliers spring and then riveting the keyring piece on that. I used 2 rivets and I think its on there solid enough.
Great work as always Syph in the "Adventures into Ti" thread - Amazing and ingenious approach to your build challenges once again.
Was the new KR originally from a liner or spring?I like the way you cut (milled) out a wee hole for the pliers pivot.
However if you had put the tools the other way round maybe that would not have been necessary?
Or even reversed the pliers - But I guess the spring would not work then?One general comment for everyone...
I love all these variations and mods - And obvioulsy the scales are something very special, different and new.
But it still amazes me that folk want such variations in the toolsets
I just think there are so many options with the catalogue models - Why not just go with one of those ???
I know you do Syph!! As does Def and many others here?And often with these variations - I think folk are missing out on tools
Eg this one - No blade or operners - I cannot imagine a SAK without those ???
Or the Rogueneer - No saw? - Why not take that too?? :oI guess I like to be different [emoji6]
I don't use a wood saw, and prefer it to be on my MT if I do have one.Sent from my SM-G920R4 using Tapatalk
-
Yeah, that's a damn nice Rogueneer right there. Excellent work my friend

Sent from my SM-G920R4 using Tapatalk
Now you must dub it the Ti Rogueneer when referencing the Rogueneer hereinafter today [emoji2]
Sent from my electronic multi-tool.
I agree. That or Rogueneer Ti
Either one sounds good.Sent from my SM-G920R4 using Tapatalk
-
TiRogueneer has a nice ring to it

-
@Syph007 said:
Here is something a bit different. Just a two layer SAK but the customer wanted a keyring on there too. Normally that is in the blade layer, but since there is no blade layer I had to figure something else out.I ended up milling some off the end of the pliers spring and then riveting the keyring piece on that. I used 2 rivets and I think its on there solid enough.
I suppose I could have hand cut a custom liner with the keyring build into that, but that felt like more work then this method... maybe it would have been similar though.




Oh man. I love the scissor and plier only setup.

-
Here is something a bit different. Just a two layer SAK but the customer wanted a keyring on there too. Normally that is in the blade layer, but since there is no blade layer I had to figure something else out.
I ended up milling some off the end of the pliers spring and then riveting the keyring piece on that. I used 2 rivets and I think its on there solid enough.
Great work as always Syph in the "Adventures into Ti" thread - Amazing and ingenious approach to your build challenges once again.
Was the new KR originally from a liner or spring?I like the way you cut (milled) out a wee hole for the pliers pivot.
However if you had put the tools the other way round maybe that would not have been necessary?
Or even reversed the pliers - But I guess the spring would not work then?One general comment for everyone...
I love all these variations and mods - And obvioulsy the scales are something very special, different and new.
But it still amazes me that folk want such variations in the toolsets
I just think there are so many options with the catalogue models - Why not just go with one of those ???
I know you do Syph!! As does Def and many others here?And often with these variations - I think folk are missing out on tools
Eg this one - No blade or operners - I cannot imagine a SAK without those ???
Or the Rogueneer - No saw? - Why not take that too?? :oYa Ive been doing the cutout on the scale adjacent to the plier to avoid having to have a liner there and since the scale is Ti, its plenty strong with some milled out. I had to do it this way as if I swapped the layers the scissors nail nick is blocked.
It is interesting to see how many different model configurations people come up with. There has definitely been an increase in the bladeless ones requested lately.
-
Syph, you're really turning out some great mods lately (well, you always are)!
I hope you don't mind me asking a couple questions in your thread as I'm stuck on a decision for my hopeful custom order. Any word on Ti liners? Do the Ti liners make it much stronger? Do the Ti liners make the tools harder to open? You mentioned you had the nickel silver liners. Is one option better than the other or just trade offs of pros and cons? I keep debating back and forth but I don't know the answers so I'm caught in my own logic loop! :ahhh
And if you're turning out Swiss Army Knives without knives, are they Swiss Army Tools (SATs) or something else?
-
Monrogue likes lots of tools on his SAKs.


Here is the front side....

And the other front side.... :D

-
There's my precious beast[emoji2]
Technically I have two precious beasts now....thanks Syph[emoji16]Sent from my SM-G920R4 using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login