Does anyone else have this problem
-
From the look of the pic,the lock hasn't fully engaged in the can opener. That means the bit driver isn't being held closed,hence the flop
-
@kirk13 said:
From the look of the pic,the lock hasn't fully engaged in the can opener. That means the bit driver isn't being held closed,hence the flopThat's what I thought but with the tools closed it still has the same looseness .
I think the bolt holding the assembly together may be loose I'll have to get another set of security torx to see if I can tighten it up if not I'll just send it in
Might be a missed QC.
Brüder, die Brüdern Helfen
-
On my Wave and Surge, the bit driver is pretty loose compared to the can opener. Not loose enough to be floppy, but it was getting looser with every use before I tightened up and Loctite'd the security torx pivot. Now the bit driver is just right. The can opener is pretty hard to get out, but I don't use it very often anyway. ¯_(ツ)_/¯ Good luck, hope yours turns out better.
-
@metasyntax said:
On my Wave and Surge, the bit driver is pretty loose compared to the can opener. Not loose enough to be floppy, but it was getting looser with every use before I tightened up and Loctite'd the security torx pivot. Now the bit driver is just right. The can opener is pretty hard to get out, but I don't use it very often anyway. ¯_(ツ)_/¯ Good luck, hope yours turns out better.Thanks metasyntax [emoji4]
Brüder, die Brüdern Helfen
-
This is familiar.
I've not been carrying my wave for a while, so I can't remember if I solved it or ignored it.
I might have a scrounge this afternoon and see if I can find it and work out what was going on.
-
Both my Surge and Wave were floppy. Just gave the screw another 90 degrees and I haven't touched them since!
-
From what I have seen an inside tool being locked open does not lock out the other tools. They are kept in place in the handle by friction. So tightening that pivot screw like others have suggested seem to be the solution.
-
My BO Surge was not tight on those tools, but not as bad as yours. I hardly feel any friction between those tools. I guess a set of security torx is on order. Is it a T8 or a T10, anyone knows? Any recommended reputable seller?
-
@chrono said:
My BO Surge was not tight on those tools, but not as bad as yours. I hardly feel any friction between those tools. I guess a set of security torx is on order. Is it a T8 or a T10, anyone knows? Any recommended reputable seller?I think it's a T10 and you have to have two of them with one the pivot just spins.
-
@super m said:
My BO Surge was not tight on those tools, but not as bad as yours. I hardly feel any friction between those tools. I guess a set of security torx is on order. Is it a T8 or a T10, anyone knows? Any recommended reputable seller?
I think it's a T10 and you have to have two of them with one the pivot just spins.
Actually, only one is needed but I highly recommend using two.
The pivot hole (on frame) and pivot pole on the end of handles are not perfectly rounded, a measure to prevent tool clump.
The screw is on the blade side of the handle, pivot pole is on the other, if you to torque to pole, the force will apply on the frame and might because damage to the frame. It is hard for me to explain but once you opened up the tool you will see. -
@super m said:
My BO Surge was not tight on those tools, but not as bad as yours. I hardly feel any friction between those tools. I guess a set of security torx is on order. Is it a T8 or a T10, anyone knows? Any recommended reputable seller?
I think it's a T10 and you have to have two of them with one the pivot just spins.
Actually, only one is needed but I highly recommend using two.
The pivot hole (on frame) and pivot pole on the end of handles are not perfectly rounded, a measure to prevent tool clump.
The screw is on the blade side of the handle, pivot pole is on the other, if you to torque to pole, the force will apply on the frame and might because damage to the frame. It is hard for me to explain but once you opened up the tool you will see.forget everything I just said, that only applys to Wave series.
-
I suppose that this problem will be difficult to eliminate because the minor tools like bitholder and can opener do not lock at all in the closed position. The slightest cause of friction among them tends to have them pop up together. One solution could be to disassemble the tool and clean/polish the mating surfaces of the two tools, but I suppose this is too complicated. This would remove the particles stuck between the tools that presumably increase attrition. A third attempt is to go somewhere where compressed air is available and open/close the two tools distinctly from each other several times under a compressed air jet until the particles that presumably cause the extra attrition are eventually blown out. Another solution coud be to try and give a droplet of oil between the two tools to decrease attrition. If this doesen't work your bitholder will ever come up that way until it stops - at the rear - with its locking plate against the locking web of the locking nose. Then you will need to close it each time you use the can opener. This is however no technical defect. Hope you will enjoy your Wave nonetheless. I have mine also only for a few weeks and am very satisfied.
-
@JM_Toolfan said:
I suppose that this problem will be difficult to eliminate because the minor tools like bitholder and can opener do not lock at all in the closed position. The slightest cause of friction among them tends to have them pop up together. One solution could be to disassemble the tool and clean/polish the mating surfaces of the two tools, but I suppose this is too complicated. This would remove the particles stuck between the tools that presumably increase attrition. A third attempt is to go somewhere where compressed air is available and open/close the two tools distinctly from each other several times under a compressed air jet until the particles that presumably cause the extra attrition are eventually blown out. Another solution coud be to try and give a droplet of oil between the two tools to decrease attrition. If this doesen't work your bitholder will ever come up that way until it stops - at the rear - with its locking plate against the locking web of the locking nose. Then you will need to close it each time you use the can opener. This is however no technical defect. Hope you will enjoy your Wave nonetheless. I have mine also only for a few weeks and am very satisfied.In the tool closed position on the bit driver and can opener side the tools will not stay closed they flop around and hang out of the handle about 1/2 an inch no mater which one is in the locked position. You can even close the handles and shake the tool ( LM Wave ) and hear them rattle.
While using the can /bottle opener you have to hold the bit driver closed with your finger because it will fall out and get in the way. The other handle ... The tools stay closed while anyone is in use.
-
OK I've snugged up the security torx and problem solved they are tight a little to tight but they will wear in nicely.
Thanks everybody for your input .
Mario.
Brüder, die Brüdern Helfen

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login