Skeletool RX?
-
Is no one else concerned about the bit adapter holding up to the strain of punching through a window? I've never actually done it, but doesn't breaking a window require a fair amount of force?
I'm kinda more bothered by the idea that you have to either open of half open the tool to use the glass breaker.....
I think it would be annoying, and slightly fiddly, but not terrible. You'd just have to hold it like this, only backwards:

(pic blatantly
stolenborrowed from J-Sews
)I'd really be more concerned about the other side of the glass breaker bit getting ruined (when it pushes against the bit holder), or busting completely through the bit holder, not to mention screwing up the bit lock.
I was thinking about that exact point this morning. But then I thought about the scenario for using the tool: emergencies. If someone is bleeding out in an over-turned vehicle, or stuck in a vehicle that is on fire, the well being of your tool is an afterthought when the well being of a life is in jeopardy. You probably wouldn't ever use the glass-breaker except under duress. If you were going to use it for gee-whizz, I think you'd have to weigh the risk vs reward.
Surely Leatherman tested it, right?
-
Is no one else concerned about the bit adapter holding up to the strain of punching through a window? I've never actually done it, but doesn't breaking a window require a fair amount of force?
I'm kinda more bothered by the idea that you have to either open of half open the tool to use the glass breaker.....
I think it would be annoying, and slightly fiddly, but not terrible. You'd just have to hold it like this, only backwards:

(pic blatantly
stolenborrowed from J-Sews
)I'd really be more concerned about the other side of the glass breaker bit getting ruined (when it pushes against the bit holder), or busting completely through the bit holder, not to mention screwing up the bit lock.
I was thinking about that exact point this morning. But then I thought about the scenario for using the tool: emergencies. If someone is bleeding out in an over-turned vehicle, or stuck in a vehicle that is on fire, the well being of your tool is an afterthought when the well being of a life is in jeopardy. You probably wouldn't ever use the glass-breaker except under duress. If you were going to use it for gee-whizz, I think you'd have to weigh the risk vs reward.
Surely Leatherman tested it, right?
I absolutely agree. If I found myself in a situation like that, I wouldn't hesitate for a second to use the tool, regardless of the damage to the tool.
However, this tool is aimed at emergency response personel, who likely have a need to use tools like glass breakers very often (sometimes even multiple times a day). So the question is, will this tool work long term for someone in that line of work? Im not convinced that the skeletool frame will hold up to multiple strikes on the bit adapter
-
@sLaughterMed said:
Is no one else concerned about the bit adapter holding up to the strain of punching through a window? I've never actually done it, but doesn't breaking a window require a fair amount of force?that's a good point.. as a former extrication technical rescuer I can say this... as long as what your breaking the glass with is a small point and strong material it doesn't take that much force.. just the opposite if your using a larger point to break glass it take much more force.. which is why most rescue squads and fire departments carry a couple spring loaded punches on each truck to break windows with.. its strong and requires little force to do saving time and effort
-
Is no one else concerned about the bit adapter holding up to the strain of punching through a window? I've never actually done it, but doesn't breaking a window require a fair amount of force?
I'm kinda more bothered by the idea that you have to either open of half open the tool to use the glass breaker.....
I think it would be annoying, and slightly fiddly, but not terrible. You'd just have to hold it like this, only backwards:

(pic blatantly
stolenborrowed from J-Sews
)I'd really be more concerned about the other side of the glass breaker bit getting ruined (when it pushes against the bit holder), or busting completely through the bit holder, not to mention screwing up the bit lock.
TBH,the photo demonstrates exactly my concern. I wouldn't fancy having to strike glass holding a shape like that.
It's also a bit of a moot point...I sold my Skeli years ago,and have never missed it ;)
-
I can see LM selling LOTS of those glass breaker bits from the Skeletool RX ( so long as they fit other LM bit holders and LM choose to market them).
I think they will. They'd be dumb to not sell them. And they will work better in the Wave/Charge/Surge than in the Skeletool since you can lock the driver out with the tool closed - better grip. With the Skele, you would be striking the window with the tool either half opened - which could then collapse at the pliers, or fully opened - which would be awkward whilst striking. I don't understand why they wouldn't work something onto the outside of the carabiner area for glass breaking. Or at least make the glass breaker bit long enough to protrude past the carabiner
I am still not sure how practical the glass break bit is, sine it took the place of phillip drive, which I think it is one of the most Frequently used tool.
Most LM only holds one bit, if you store the glass break bit in MT that means you will have to get out the bit kit often. Or if you store the glass break bit somewhere else, do you think there will enough time to get it installed in case of emergency? -
I can see LM selling LOTS of those glass breaker bits from the Skeletool RX ( so long as they fit other LM bit holders and LM choose to market them).
I think they will. They'd be dumb to not sell them. And they will work better in the Wave/Charge/Surge than in the Skeletool since you can lock the driver out with the tool closed - better grip. With the Skele, you would be striking the window with the tool either half opened - which could then collapse at the pliers, or fully opened - which would be awkward whilst striking. I don't understand why they wouldn't work something onto the outside of the carabiner area for glass breaking. Or at least make the glass breaker bit long enough to protrude past the carabiner
I am still not sure how practical the glass break bit is, sine it took the place of phillip drive, which I think it is one of the most Frequently used tool.
Most LM only holds one bit, if you store the glass break bit in MT that means you will have to get out the bit kit often. Or if you store the glass break bit somewhere else, do you think there will enough time to get it installed in case of emergency?It looks like the bit in the handle is the combo flat/phillips bit, like the one that comes in the Wave. The opposite of the glass-breaker also appears to be a flat. I think the idea with the RX, is to leave the glass-breaker in, and swap to the Phillips or flat as needed, and then switch it back afterwards. At least that is how I would do it, because you are right, if you were rocking the Phillips (which I use most of the time) while driving down the road and a car crash happens right in front of you, probably would not be good trying to fumble around with a tiny bit while responding.
I think probably EMTs, Police Officers, or other emergency responders would not use this, at least not as a primary rescue tool. Maybe a backup. They would all probably have access to something better. A ResQme is a better glass breaker. A strap cutter removes virtually ALL chance of accidentally cutting the victim. I think this is a pretty decent combo of an EDC mulitool and a ER tool, but it could have been a lot better.
-
Rusted pliers already on one of these? :(
https://www.youtube.com/watch?v=HrNGnvrjrwU
Still looks sweet to me. Probably getting one.
;) -
That Skeletool is just KILLER!!! Leatherman has out-done themselves, IMHO :D

-
I emailed leatherman and to my surprise they emailed me back.. they are...as of right now... unsure if they will be selling the breaker bit as a replacement part to put on other tools
-
@rescue4500 said:
I emailed leatherman and to my surprise they emailed me back.. they are...as of right now... unsure if they will be selling the breaker bit as a replacement part to put on other toolsNo worries, they will.
-
I emailed leatherman and to my surprise they emailed me back.. they are...as of right now... unsure if they will be selling the breaker bit as a replacement part to put on other tools
No worries, they will.
If they think they can make a profit doing it I bet they will. If they do not I doubt they will.
-
@Padre said:
Rusted pliers already on one of these? :(
https://www.youtube.com/watch?v=HrNGnvrjrwU
Still looks sweet to me. Probably getting one.
;)So Leatherman is finally making a multi you can customize by hand picking the implements to include... and it's the Tread.
-
Meh. :P
-
I won't be getting one, but I do like the idea of different colors and the blade shape with longer serrations looks like it would lend itself well to being a more heavily used tool.(Frequent use, not more difficult).
I enjoy my skeletool, not my favorite but I think it does make a good minimal carry with a blade on par with a lot of knives I have.
-
As much as I believe they really half-arsed their effort on the Skeletool RX (sigh) I do still sort of want one.
::)
-
Some people have complained about the Skeletool RX's lack of an oxygen tank wrench. Although LM doesn't say it has one, the truth is that the RX can in fact be used to open oxygen tanks.
Assuming the RX has the same pliers and the regular Skeletool, I just used mine (the regular Skeletool) to open an oxygen bottle. The valve fits pretty well into the opening of the pliers.
-
@JJR512 said:
Some people have complained about the Skeletool RX's lack of an oxygen tank wrench. Although LM doesn't say it has one, the truth is that the RX can in fact be used to open oxygen tanks.Assuming the RX has the same pliers and the regular Skeletool, I just used mine (the regular Skeletool) to open an oxygen bottle. The valve fits pretty well into the opening of the pliers.
Good to know. Thank you.

-
@JJR512 said:
Some people have complained about the Skeletool RX's lack of an oxygen tank wrench. Although LM doesn't say it has one, the truth is that the RX can in fact be used to open oxygen tanks.Assuming the RX has the same pliers and the regular Skeletool, I just used mine (the regular Skeletool) to open an oxygen bottle. The valve fits pretty well into the opening of the pliers.
Aren't the pliers harder than the valve material though? If so, wouldn't that scar up the tank?
-
It could. But the valves are not cranked down like nut on a bolt. Or at least not the ones I have came across.
That's us mobile
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login