And so it begins.... (My adventures into Alox!)
-
Some vanilla alox today... :D



-
Hey Syph - do the pocket clip screws just go in to the alox scales, and that provides a good enough bite, or is there more to it? What do you do, just pre drill a hole that's a little smaller?
-
@tommywp said:
Hey Syph - do the pocket clip screws just go in to the alox scales, and that provides a good enough bite, or is there more to it? What do you do, just pre drill a hole that's a little smaller?Oh yes the screws hold well. For a 2-56 thread in aluminum you drill a #51 hole and tap. In Ti I do a larger hole since it is significantly tougher material the threads dont need to be as deep to hold, and I actually only tap half way through the scale.
-
That was some pretty fast turnaround time on your brass mag glass frames! Can't wait to see the finished product... :)
-
@batosai117 said:
We shall dub it the Shawshank modelOK ...... OCD kicking in :( :o
Didn't he escape using a geologist's hammer - not a file ???
Still love the name though

-
We shall dub it the Shawshank model
OK ...... OCD kicking in :( :o
Didn't he escape using a geologist's hammer - not a file ???
Still love the name though

This is true. But I couldn't think of any other good prison title to go with the file, lol. Perhaps the "Alcatraz" would work too
Sent from my electronic multi-tool.
-
The Great Escape Artist? Too long?
-
Brass mag glass holders are ready for pickup!!! Im heading over now to get them, and the new 91mm Ti scales. :D
Will post pics in a few hours (It's the next city over, but not too far)
-
Woo Hoo!!! :ahhh
-
Any word on the Marlin Spike parts you were working on?
-
@Toolslinger said:
Any word on the Marlin Spike parts you were working on?I was going to run those next, but I was almost out of Ti scales for 91s, so I really needed those more. I'm doing the marlin spikes next for sure. Its just a pricey job since the hunk of steel I bought is large, so its going to be about $700 for cut cost, but that will give me about 200 spikes.
-
Lots of parts! :D
111 Ti scales, mostly 91s, some 84s, and 2 new types of wrench scales that thankfully work much much better than last design.



-
Oh smurf yea!
-
It's really amazing to see the endless configurations that poeple want. Great job Syph.
What is your process for official orders? -
@Demel said:
It's really amazing to see the endless configurations that poeple want. Great job Syph.
What is your process for official orders?Yes, the funny this is, if it was up to me I would probably only build a few configurations. But Ive found that people really have different ideas about what a tool should have for them. So being flexible and providing as many options as possible is the main reason I think I still get alot of orders.
If you want a quote on something just shoot me a PM or email. I keep a list of orders and work on them in order. Im not running too far behind any more, probably 2-3 week lead time as long as Ive got the parts in stock. The nice thing about mostly doing Ti work is that it's easier for me to keep a stock of scales, and for donor SAKs I keep checking amazon or other places and order a bunch of donors when they go on sale.
I think the brass mag holders will work out nice, but the cost per part is creeping up and I haven't added the labor yet to do the finish work and tap for set screw. I only got 19 out of 6 square inches of brass. The cost for the brass + waterjet puts me at 9 bucks per part so far. Im going to finish one up in the morning and figure out how much labor is involved for finish work. The pieces are 0.125" thick and I have to shave them down to 0.110", then sand and polish and tap a 2-56 hole in there.
-
Not that we use the current plastic frames as prybars, but the sturdiness afforded by the brass, combined with the ability to replace the lens, will personally add a level of confidence in it's use that the plastic just doesn't give. Plus, the cool factor is just off the chart... :D
-
@Syph007 said:
I think the brass mag holders will work out nice, but the cost per part is creeping up and I haven't added the labor yet to do the finish work and tap for set screw. I only got 19 out of 6 square inches of brass. The cost for the brass + waterjet puts me at 9 bucks per part so far. Im going to finish one up in the morning and figure out how much labor is involved for finish work. The pieces are 0.125" thick and I have to shave them down to 0.110", then sand and polish and tap a 2-56 hole in there.Dangerous, I thought the one of your Ti models I got would be that "last knife I ever need"; but with the possibility of a brass lens- I'm weakening again.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
