Darkpsyche's FEBRUARY CHALLENGE MT.O CYBERTOOL thread
-
Day 3 tea break! (Don't mind the mug)

Sent from my SM-G900V using Tapatalk
-
Day 4: Including it into a new electronic repair edc kit


Also includes:
- leatherman es4 squirt
- wires
- solder less connectors
- microfiber cloth
- 10 double sided bits (to fit into cybertool drive)
I had to strip some wires but used the Cybertool instead of the leatherman strippers, just cuz I can :P
Sent from my SM-G900V using Tapatalk
-
Day 5: stripped some wires for a computer fan

Sent from my SM-G900V using Tapatalk
-
Starting off the weekend with a cold one

Sent from my SM-G900V using Tapatalk
-

Day 6: replacing a battery for my multimeter
Sent from my SM-G900V using Tapatalk
-
@darkpsyche said:
Starting off the weekend with a cold one
Sent from my SM-G900V using Tapatalk
Ah, nice! That reminds me to drive to Germany soon to pick up some crates of Becks! :D
-
Day 7: making new friends - The TS100 soldering iron!
Used the Cybertool to screw in the soldering tip.
Sent from my SM-G900V using Tapatalk
-
I'm going to try to use all the tools on the cyber tool by the end of this challenge :D
In recap:<u>Main Tools</u>
Small Knife:
Driver:
Cap Opener:
Large Flat Screwdriver:
Wire Stripper:
Small Flat Screwdriver:
Can Opener:
Mini Flat Screwdriver:
Corkscrew:
Awl:
Large Knife:<u>Scale Tools</u>
Pen:
Tweezers:
Pick:
Pin: -
Day 8: Just making some lists for the day.

Sent from my SM-G900V using Tapatalk
-
Nice pic layout. B&W and minimalist.
-
Straight from the motherland, I'm jealous!

Starting off the weekend with a cold one

Sent from my SM-G900V using Tapatalk
Ah, nice! That reminds me to drive to Germany soon to pick up some crates of Becks! :D
-
Thanks!
@pettydroid said:
Nice pic layout. B&W and minimalist. -
@darkpsyche said:
Straight from the motherland, I'm jealous!
Starting off the weekend with a cold one

Sent from my SM-G900V using Tapatalk
Ah, nice! That reminds me to drive to Germany soon to pick up some crates of Becks! :D
I live 20 miles from the german border, so I go there regularly for beer (mostly Becks and 'special beers' like IPA's), whisky etc. Its much cheaper there because the tax on alcohol is much lower than in the Netherlands.
-
@darkpsyche said:
Day 7: making new friends - The TS100 soldering iron!
Used the Cybertool to screw in the soldering tip.
Sent from my SM-G900V using Tapatalk
That soldering iron totally looks like it belongs together with your CT!
-
Can you talk us through your additional bits and the o-rings?
Do you find you use them regularly? Over the included bits?I carried my CT29 yesterday and actually got good use out of it. Fixed a door with a Philips (nice reach could not do with can opener) and adjusted a friends knife pivot with the Torx.
-
Nice!
Straight from the motherland, I'm jealous!

Starting off the weekend with a cold one

Sent from my SM-G900V using Tapatalk
Ah, nice! That reminds me to drive to Germany soon to pick up some crates of Becks! :D
I live 20 miles from the german border, so I go there regularly for beer (mostly Becks and 'special beers' like IPA's), whisky etc. Its much cheaper there because the tax on alcohol is much lower than in the Netherlands.
-
They shall be BFFs, till the day victorinox includes a soldering iron in one of their models!
Day 7: making new friends - The TS100 soldering iron!
Used the Cybertool to screw in the soldering tip.
Sent from my SM-G900V using Tapatalk
That soldering iron totally looks like it belongs together with your CT!
-
Sure, the double sided bits are from a screwdriver kit, if you google "30-in-1 Extendable Flex Shaft Precision Screwdriver Set" you can find several.
The O-rings are from metricscrews.us, the specific part is: Rubber Washer 2mm ID x 4mm OD x 1mm CS (10532)
I also have 4 small magnets glued in the driver socket and in each bit holder.
The bit case is from an old radio shack precision bit driver kit.
@shark_za said:
Can you talk us through your additional bits and the o-rings?
Do you find you use them regularly? Over the included bits?I carried my CT29 yesterday and actually got good use out of it. Fixed a door with a Philips (nice reach could not do with can opener) and adjusted a friends knife pivot with the Torx.
-
.
-
Day 9: Finally got to use the pin tool! Needed to stop a computer fan to test if the sensor was working, blocked by a grate.
Also used the driver for some euro connectors.


Sent from my SM-G900V using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login