Multitool in the dishwasher? Has anyone experience with it?
-
After reading the stories i was convinced and have put my swisstool in it with all the tools folded outwards.
We will see how it comes out
If this works great i might do it every month to keep the tool clean. I use it to prep my bread that i take to work so it gets gunked up with peanut butter etc.. I also always cut the mayonaise bottles open to get the last out of it. 1 month old mayonaise doesn't look that tasty anymore :D
-
This is what victorinox advises you to do:
Cleaning
Fruit juices can flow between the blades when cleaning or cutting fruit and these become sticky after they have dried. Open and close the blades several times in warm water until they move easily again. After drying, place a small drop of oil between the blades and the tool shank or spring as well as other friction surfaces. Never clean your SwissTool or SwissTool Spirit in a dishwasher!
ARE SWISS ARMY KNIVES DISHWASHER PROOF?
The temperature in dishwashers can reach between 55 and 80 degrees Celsius (130 to 180 degrees Fahrenheit), depending on the selected cycle. Cleaning salts and strong cleaning agents are used during this process.Exposing Swiss Army Knives to aggressive environments and high temperatures for extended periods can cause damage.
Therefore, do not put Swiss Army Knives or other pocket tools in the dishwasher!

-
Or, you could soak that thing in a solvent for a couple of days (WD-40, Boeshield, CLP, etc.) and have no chance of rust. But yeah, I have run SAKs through the dishwasher with no prob. The only thing you have to be concerned with it drying it quickly and thoroughly. I prefer a hair dryer or careful application of a heat gun, followed by lube.
-
I doubt that hot water will damage the tool. But what would concern me a little is the used cleaning salt in the dishwashers. I´ve just asked my wife - the kitchen is hers - she never puts knives of any kind in the dishwasher. They always get cleaned by hand. I asked for the reason; the cleaning salt in the dishwasher will dull the edges (somehow).
Personally I doubt it - but it could be possible.
My idea - not recommendation - is: you should keep the tools which you want to keep sharp inside the handles. You could keep the tools closed - pliers opened for cleaning inside the dishwasher. The hot water should soak out the dirt, debris and whatsoever out of you tool.
-
@Humppa said:
I doubt that hot water will damage the tool. But what would concern me a little is the used cleaning salt in the dishwashers. I´ve just asked my wife - the kitchen is hers - she never puts knives of any kind in the dishwasher. They always get cleaned by hand. I asked for the reason; the cleaning salt in the dishwasher will dull the edges (somehow).Personally I doubt it - but it could be possible.
My idea - not recommendation - is: you should keep the tools which you want to keep sharp inside the handles. You could keep the tools closed - pliers opened for cleaning inside the dishwasher. The hot water should soak out the dirt, debris and whatsoever out of you tool.
Thanks for the info on the salt that is in the cleaning solvent, i will rinse the tool with water after it is ready.
At this moment it is still in the dishwasher. -
she never puts knives of any kind in the dishwasher.

You've got a diamond there, Humppa! -
It is ready!
It is almost as clean as the day it left the factory two years ago :D
I will oil all the joints again with hypoid oil after it has dried completely.
-
It does look very nice, good job.
-
I would not worry of tools that are solely of metal going through washing machine. Or boil them. Just dry and oil good, and you will manage good.
Just do not put any SAK with plastick scales in hot water. They will warp. More than 45 celsius will warp them.
-
Wash it by hand?
-
5 days have passed since i put my swisstool in the dishwasher, i haven't oiled it yet because i am lazy i
guess
I haven't found any rust spots and the tools open and close very nice, it doesn't feel gritty or hard hard to open.
I might stop oiling the joints because i have the feeling that it attracts more dust and sand then that it makes the tools easier to deploy. -
@anditsgone said:
I might stop oiling the joints because i have the feeling that it attracts more dust and sand then that it makes the tools easier to deploy.Find a dry lubricant that you like, they won't attract all the problem stuff and reduce wear and keep it operating quite smoothly depending on the lube.
-
Went through the dishwasher again yesterday. There is not rust on the tool except for the file but i guess that comes from small metal particals that are still left behind in the grooves of the file
-
I am glad (but not surprised!) to hear your Swiss tool survived the dishwasher. It is pretty much the most bulletproof tool out there.
I second the comment about a dry lubricant. I use powdered graphite whenever possible and it works great without trapping gunk in pivots. I usually use the stuff that comes in a small tube (looks like a tiny toothpaste tube) but recently I have been experimenting with an aerosol graphite. It leaves a black stain on things but it works very well otherwise.
Def
-
@Grant Lamontagne said:
I am glad (but not surprised!) to hear your Swiss tool survived the dishwasher. It is pretty much the most bulletproof tool out there.I second the comment about a dry lubricant. I use powdered graphite whenever possible and it works great without trapping gunk in pivots. I usually use the stuff that comes in a small tube (looks like a tiny toothpaste tube) but recently I have been experimenting with an aerosol graphite. It leaves a black stain on things but it works very well otherwise.
Def
I use aerosol graphite (the one used for keyholes) works great
-
@Grant Lamontagne said:
I second the comment about a dry lubricant. I use powdered graphite whenever possible and it works great without trapping gunk in pivots. I usually use the stuff that comes in a small tube (looks like a tiny toothpaste tube) but recently I have been experimenting with an aerosol graphite. It leaves a black stain on things but it works very well otherwise.Def
I don't notice any difference in the smoothness of the deployment with or without lubrication.
Even the scissors work great with oiling the joint.Although victorinox recommends oiling the joints i dont think it is needed. It is not like it is a piston or shaft that depends on an oil film or otherwise it will cease the engine.
-
@Grant Lamontagne said:
I am glad (but not surprised!) to hear your Swiss tool survived the dishwasher. It is pretty much the most bulletproof tool out there.I second the comment about a dry lubricant. I use powdered graphite whenever possible and it works great without trapping gunk in pivots. I usually use the stuff that comes in a small tube (looks like a tiny toothpaste tube) but recently I have been experimenting with an aerosol graphite. It leaves a black stain on things but it works very well otherwise.
Def
Dosen't even use his own lubricant product...... -
I'm not surprised it came out unscathed. I do believe lubricants attract ( whatever debris ) I also believe with tools that have washers the lubricant help the friction between the two surfaces.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login