Damascus 2016 Limited Edition
-
@shark_za said:
I have a friend who carries and uses a Damascus wooden Explorer from 2013.I dont think the Damascus knives are intended for use.
I had a conversation with a Victorinox Executive at a private event at the London store last year and he mentioned that the Damascus knives were indeed sold as collectors pieces and were not aimed at everyday users.
Personally I don't need to carry a Damascus blade as my "normal" blades do the job just fine.
-
@dks said:
The Victorinox Damascus blades are SS so using them should be as carefree as using a regular SS blade. They are also harder that the regular Victorinox SS blades.However, there is the possibility that after sharpening and using them the Damascus pattern will not be so nice looking (you need a special process to achieve it again).
I have a few and have no desire to use them.
Are you sure it's SS Damascus? I always thought it's a mix of 15N20 and 1095HC or some other Sandvik Carbon-ish stuff

Would you risk dipping it in an apple overnight? ... for science ::) -
Out of curiosity, where was this and were there any more?

A Canadian seller on ebay; all up with postage was between A$400-A$450. Could not get under A$500 until it appeared. Seems to be selling them still; slightly higher than when I picked them up:
Still a little too rich for my blood.... for now.
Was also hoping a bit closer to Sydney.
I did pick up a 2014 locally new in box for about A$130 off original price -
The Victorinox Damascus blades are SS so using them should be as carefree as using a regular SS blade. They are also harder that the regular Victorinox SS blades.
However, there is the possibility that after sharpening and using them the Damascus pattern will not be so nice looking (you need a special process to achieve it again).
I have a few and have no desire to use them.
Are you sure it's SS Damascus? I always thought it's a mix of 15N20 and 1095HC or some other Sandvik Carbon-ish stuff

Would you risk dipping it in an apple overnight? ... for science ::)According to this poster (if you trust him..) it is
Amici,
Damascus steel, that's Latin for "rust magnet" because that's what will happen if you ever intend to use and not instantly clean and oil it before the dreaded "R" word sets in.. When it comes to Damascus, sure is mighty pretty to look at, but that's about it.. At least for my mojo..Cheers,
SergeNot that knowledgeable in steels and never really pushed my Carl, but Victorinox seems to use Vinland - Martensitic which is shown to be stainless
http://www.damasteel.se/files/7014/1145/7994/Product_Information_Martensitic_Stainless_Damascus.pdfEven my Paki-Laguiole's cheap Damascus hasn't shown an rust spots so far...
according to him (if he can be trusted) "Victorinox seems to use Vinland - Martensitic which is shown to be stainless"
He even provides a link :D :D :D



-
The Victorinox Damascus blades are SS so using them should be as carefree as using a regular SS blade. They are also harder that the regular Victorinox SS blades.
However, there is the possibility that after sharpening and using them the Damascus pattern will not be so nice looking (you need a special process to achieve it again).
I have a few and have no desire to use them.
Are you sure it's SS Damascus? I always thought it's a mix of 15N20 and 1095HC or some other Sandvik Carbon-ish stuff

Would you risk dipping it in an apple overnight? ... for science ::)According to this poster (if you trust him..) it is
Amici,
Damascus steel, that's Latin for "rust magnet" because that's what will happen if you ever intend to use and not instantly clean and oil it before the dreaded "R" word sets in.. When it comes to Damascus, sure is mighty pretty to look at, but that's about it.. At least for my mojo..Cheers,
SergeNot that knowledgeable in steels and never really pushed my Carl, but Victorinox seems to use Vinland - Martensitic which is shown to be stainless
http://www.damasteel.se/files/7014/1145/7994/Product_Information_Martensitic_Stainless_Damascus.pdfEven my Paki-Laguiole's cheap Damascus hasn't shown an rust spots so far...
according to him (if he can be trusted) "Victorinox seems to use Vinland - Martensitic which is shown to be stainless"
He even provides a link :D :D :D



Ow my... I was just about to fight the guy who said that :-[
That was my evil twin brother... or I am the evil twin brother... let me check the link :-[
-
The Victorinox Damascus blades are SS so using them should be as carefree as using a regular SS blade. They are also harder that the regular Victorinox SS blades.
However, there is the possibility that after sharpening and using them the Damascus pattern will not be so nice looking (you need a special process to achieve it again).
I have a few and have no desire to use them.
Are you sure it's SS Damascus? I always thought it's a mix of 15N20 and 1095HC or some other Sandvik Carbon-ish stuff

Would you risk dipping it in an apple overnight? ... for science ::)According to this poster (if you trust him..) it is
Amici,
Damascus steel, that's Latin for "rust magnet" because that's what will happen if you ever intend to use and not instantly clean and oil it before the dreaded "R" word sets in.. When it comes to Damascus, sure is mighty pretty to look at, but that's about it.. At least for my mojo..Cheers,
SergeNot that knowledgeable in steels and never really pushed my Carl, but Victorinox seems to use Vinland - Martensitic which is shown to be stainless
http://www.damasteel.se/files/7014/1145/7994/Product_Information_Martensitic_Stainless_Damascus.pdfEven my Paki-Laguiole's cheap Damascus hasn't shown an rust spots so far...
according to him (if he can be trusted) "Victorinox seems to use Vinland - Martensitic which is shown to be stainless"
He even provides a link :D :D :D



Ow yes, now I remember, Corwyn is right (as usual). It is indeed a special Stainless Damascus steel and not regular Sandvik Damasteel as I had wrongly assumed...
Once again Corwyn you are a true fountain of knowledge and I bow to your insight... you are pride for us all... my favourite user by far ::)I might put my Carl in an apple just to prove my trust in this great fellow and fine steel connaisseur

-
NEW Corwyn, you need to listen to OLD Corwyn more often. He is wise :D :D :D
-
I may be wrong but don't Victorinox use Damasteel for these?
Seriously cool steel that, RWL34 is like 154CM.A Stainless Damascus.
-
Posts above while I was typing is exactly what I mean
Sent from my iPhone using Tapatalk
-
I have other knives in Damasteel as well. It's good stuff. RWL34 + PMC27. RWL34 is more like CPM154CM than 154CM, as it's a PM steel. PMC27 is a PM process 12C27.
-
The press-release of the 2012 Damascus edition (couldn't find a newer one quickly enough) says: Blade steel: Damasteel (RWL-34 & PMC-27); Bluewine pattern
..."With careful grinding,
polishing and etching the unique and characteristic patterns are reveled,
thereby providing a glimpse into the soul of the steel. (The blade
of this knife is manufactured from stainless high quality Damascus
steel, 60 HRc)." -
::)
-
The purple LE16's look great! Love those orange and green scales cellidor scales aswell!
I love those new colors! I'm really hoping the orange is a different shade than my orange Cybertool.
You Dutch people with your obsession for the colour Orange ... ::)
Just kidding, I also love my orange Hunter XT, and the "new" orange SAK looks great ;).
-
I have a friend who carries and uses a Damascus wooden Explorer from 2013.
I dont think the Damascus knives are intended for use.
**
I had a conversation with a Victorinox Executive **at a private event at the London store last year and he mentioned that the Damascus knives were indeed sold as collectors pieces and were not aimed at everyday users.Personally I don't need to carry a Damascus blade as my "normal" blades do the job just fine.
Which one? This?

Or this?

:D :D
-
I have a friend who carries and uses a Damascus wooden Explorer from 2013.
I dont think the Damascus knives are intended for use.
**
I had a conversation with a Victorinox Executive **at a private event at the London store last year and he mentioned that the Damascus knives were indeed sold as collectors pieces and were not aimed at everyday users.Personally I don't need to carry a Damascus blade as my "normal" blades do the job just fine.
Which one? This?

Or this?

:D :D

-
I have a friend who carries and uses a Damascus wooden Explorer from 2013.
I dont think the Damascus knives are intended for use.
**
I had a conversation with a Victorinox Executive **at a private event at the London store last year and he mentioned that the Damascus knives were indeed sold as collectors pieces and were not aimed at everyday users.Personally I don't need to carry a Damascus blade as my "normal" blades do the job just fine.
Which one? This?

Or this?

:D :D

Now my colleague asked me why I was laughing at my screen :D
-
What a year for us Victorinox Fans ;)
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
-
I like the look of all those new translucent scale colours a lot, especially the gold. Not so sure about the 2016 purple alox, but I expect I'll end up buying one anyway.
-
I see several wants right there.
Curious about the Desert camo Huntsman
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login