What did you use your Sak on today?
-
Love this stuff

-
This kitchen cabinet door with Euro style hinges would not close all the way.

Efforts to tweak the springs and other adjustments were for naught. Time to replace the hinges. This is a job for the 111mm Work Champ (this one in sterile OD livery)

Upon removing the door and old hinges we find under the lower hinge . . . the installer had broken off a screw head attaching it to the cabinet frame, just left it in place, and drove another at an angle below it.


Good thing the Work Champ has pliers, so we can do what the cabinet installer should have done nearly 20 years ago

We also do with the screws going into the solid oak cabinet frame what the original installer should have done to prevent torquing a screw head off. Just a little bit of bar soap on the screw threads will prevent them from binding in the wood. Acts as a lubricant and as friction heats up the screw, the soap becomes fluid. Amazing how this works!

New hinges were attached to the door, and then the door was mounted to the cabinet frame. It now closes completely as it should.

Some failure analysis on the old hinges to determine why they failed. Turns out the bushing on the lower one that is needed for the spring to keep the door closed had cracked and broken. The piece fell out as I was removing the door, and the analysis showed where it had come from. The screw with missing head may have contributed as it kept the hinge mount from being flush with the door frame, allowing it to rock, but that's a stretch with no real evidence to back it.

John
-
Right on John!!!!!

-
To hold my beer money.

-
I had some time offline so I put together a simple Vic Fire Sheath.

More pix in the Fire Kit thread..
/post/1232127 -
Way to go Robert....makes a great combo!

-
This was yesterday, but it was late in the day. Not quite as big a job as the cabinet door hinges, but there was a surprise waiting that increased the amount of time consumed by what should have been a simple task . . .
There was, until late last night, a small flip-up flat screen TV mount under a kitchen corner cabinet. The TV hasn't been there for several years, but the mount remained, flipped up under the cabinet. It would start drooping about every year or so and I would have to tighten the hinge on its friction bushings to make it stay up (gravity is relentless) . . .

Not only that, the installer (not me) had driven one of its mounting screws through the bottom of the cabinet and although it wasn't in a location where it was likely anything would get set on it, this was very sloppy work, and every time I saw it was like having a stone in my shoe.

Time for it to come down, permanently, and I set about removing it using the Delemont EvoGrip S557, which is more compact and better for working in tighter or more difficult to access spaces. In addition, its in-line Phillips locks up when pushed against a screw head to keep it from folding up, just like the bottle opener does with its flat-tip.

First thing I noticed when looking for the mounting screws was the right one not fully seated. This explained why only one of them protruded into the cabinet. Only one screw was holding most of the weight. Even more sloppy work!

The first screw came out OK.

Then I discovered why the second one had never been driven in completely. The Phillips head was stripped out. Fortunately, the pliers were thin enough to get under the round head (which defied gripping) and get some purchase on the threads to back the screw out

What a perfectly nice cone inside the screw head! The installer had used a power driver and when the screw bound up, she kept on churning and chattering away hoping it would magically motivate the screw to start turning again. A drill with a drill bit couldn't have done much better!!

The protruding screw in the cabinet is gone, as is the droopy flat screen TV mount, and yet another burr under my saddle eliminated . . .

The mount is now in storage alongside some other currently unused TV and computer monitor hardware.
John
-
February 24th . . .
It was not quite as involved as the past couple of days . . . in fact pretty simple. Used the Wenger Evolution Nail Clip AT to trim my fingernails. It is marvelously sharp, better than most of the "standard" nail clippers, and the nail file is excellent. The "AT" means it's an "Air Travel" model without a pen blade. Instead, it's a tiny screwdriver about the size you'd use to tighten screws on your glasses. Kind of a shame that Victorinox only continued the Nail Clip 580 which has a pen blade and will get confiscated at an airport, or any other screening point like most courthouses.

Then . . . in what is perhaps one of the most common office uses of a SAK's bottle opener, and it's not for getting that brewski opened a beer-thirty, it's for using the flat-tip driver as a staple puller, several of which were in this envelope that arrived today. The knife on my belt just happened to be the Delemont Evolution S16, but for this task any of the 85mm or 91mm, or even the Alox Pioneer would have worked just fine.


John
-
I used my MechaRogue's scissors to trim some stray beard whiskers. Also used the glass nail file in my Swisscard to file my nails. That's probably the best nail file I've used

Sent from my SM-G920R4 using Tapatalk
-
Used the Tinker to install a LED Light Bar in the kitchen.
-
Already posted earlier in the SAK and coffee . . . the coffee grinder would not start this morning at zero-dark-thirty. Desperate times call for desperate measures. The Delemont Evolution S557 was the first one I laid hands on with pliers to use as a sub-miniature jaw crusher. It worked well enough to get the go-juice made, much better than a mallet with a Ziploc! Tomorrow will probably be use of a SAK to fix the grinder.

John
-
To enjoy life :)

-
My first post here.
I used my old Camper as a companion in the woods today. I went for a stroll looking for the spring, and I belive I found it on top of this very rock.
-
Welcome to the boards jonyb.
Nice pic. 
-
My TiRogueneer got some use at our little girl's bday party. Scissors and E-blade to open various things.
Sent from my SM-G920R4 using Tapatalk
-
+3
!! -
To fix this two, and for the first time I ruin something, broke the earpiece on the wiko, now I really don't know we're I can find a spare one, frustrating!


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login