SAKs & Coffee
-
@magentus said:
I'm not doubting your technical prowess Jalind, but does your Rambler have a sensitive bladder that might equate to the puddles found near the stunt site? I know I feel quite nervous myself before performing anything death defying. Just thought I'd mention it to maybe save you some time.Perhaps we have put too much pressure on your poor Rambler's bladder.

-
@magentus said:
I'm not doubting your technical prowess Jalind, but does your Rambler have a sensitive bladder that might equate to the puddles found near the stunt site? I know I feel quite nervous myself before performing anything death defying. Just thought I'd mention it to maybe save you some time.Perhaps we have put too much pressure on your poor Rambler's bladder.
Interesting thought. Found the towel used to mop it up. Fluid is quite clear in color and does not have any ammonia odor.
I've got the coffee maker partially disassembled and determined the failure mechanism. It is exactly the common problem my Google search had found (seepage around a gasket from lime scaling and age). Found one other issue in the process, and some critical parts are soaking in white vinegar for a while to aid in their de-scaling. It's a simple design using gravity and heating elements to keep the water hot, and to keep the pot hot (both are switched), without any percolation or reliance on steam generation to push the water into the filter basket. Disassembly of the top to get to everything needing work was also easy. De-scaling the upper chamber (akin to chipping paint) and refurbishing two gaskets with their related bits are taking some time.
In fairness to Bunn, the coffee maker is over five years old and the water here is hard with lime. The routine de-scaling maintenance Bunn recommends has kept other parts sufficiently de-scaled, but cleaning out what I have been this morning requires disassembly and it's something that periodic vinegar flushing isn't going to prevent.
John
-
so what SAKs did you use for the task ?

-
@eamo said:
so what SAKs did you use for the task ?
Used the Cyber Tool 34 (as I'm doing the STACK Challenge) -- these are just a few of the pix
The Culprit: this gasket between the lower reservoir that keeps water at 200F (93C) for the next pot of coffee and the upper, temporary reservoir into which you pour water when making the next pot. Gravity pushes the hot water in this tank through a tube at the bottom up into the filter bowl. You can see stains around it where water had seeped out. It then flowed out over the side of the reservoir and out the bottom of the coffee maker. The seepage is why there was always a small puddle.

Driving the last screw into the top during reassembly . . .

The "Smoke Test" making the first pot after reassembly. If none of the pressurized smoke that makes all things electrical run leaks out, it's successful. And I'll bet you thought it ran on electrons. The proof it runs on pressurized smoke? Whenever it leaks out, electrical and electronic devices quit working. That's my story and I'm sticking to it. This first pot after reassembly was done in right at about 3 minutes flat, the fastest I'd gotten a pot of coffee from this machine in several years!

Cyber Tool 34 sampling the fruits of his labors

The upper reservoir was only about 99% de-scaled, but two gaskets and a short tube were completely cleaned, and that will have to suffice for now. I was getting desperate for the java. I'll be watching for more seepage and if there is any I know where to add an O-ring onto that gasket to completely seal it up.
John
-
job well done - how did the coffee taste ?
-
so what SAKs did you use for the task ?

Used the Cyber Tool 34 (as I'm doing the STACK Challenge) -- these are just a few of the pix
The Culprit: this gasket between the lower reservoir that keeps water at 200F (93C) for the next pot of coffee and the upper, temporary reservoir into which you pour water when making the next pot. Gravity pushes the hot water in this tank through a tube at the bottom up into the filter bowl. You can see stains around it where water had seeped out. It then flowed out over the side of the reservoir and out the bottom of the coffee maker. The seepage is why there was always a small puddle.

Driving the last screw into the top during reassembly . . .

The "Smoke Test" making the first pot after reassembly. If none of the pressurized smoke that makes all things electrical run leaks out, it's successful. And I'll bet you thought it ran on electrons. The proof it runs on pressurized smoke? Whenever it leaks out, electrical and electronic devices quit working. That's my story and I'm sticking to it. This first pot after reassembly was done in right at about 3 minutes flat, the fastest I'd gotten a pot of coffee from this machine in several years!

Cyber Tool 34 sampling the fruits of his labors

The upper reservoir was only about 99% de-scaled, but two gaskets and a short tube were completely cleaned, and that will have to suffice for now. I was getting desperate for the java. I'll be watching for more seepage and if there is any I know where to add an Onion-ring onto that gasket to completely seal it up.
John
Fixed. When is THE WALK?
-
-
You're a real hotshot Mags

My CT41 play it save and relaxed today

-
-
-
The Walk -- Part 3
With some delay due to inability to make coffee, we proceed now with Part 3. While working the coffee maker yesterday I had it inverted draining all the water out and saw the date code. It was made in 2006, a couple months shy of ten years ago, a few years older than I had thought (it's my second Bunn of the same model).
If you recall, we had high wire failure. This has been redesigned with much stronger cable. Note the cable is now red, to prevent any inadvertent use of the old white cable, and it's anchored securely around the carafes. In addition, there were other technical challenges, such as the carafes sliding on the counter whenever there was much mass placed on the new cable, even if they were filled with water. Non-skid pads have been added under them to prevent sliding. To test its tensile strength, the Woodsman, Craftsman and Champion all volunteered to test the cable:



The cable was then tested to ensure it would not fail in hurricane force winds . . .

Finally, we have the pre-show before the main event. What daredevil event would go on without one? As the audience has once again gathered, a distant cousin of the Gambler Rambler prepares to bungee jump over the cauldron of roiling hot coffee, using a thin bungee cord around but one tool!. His stage name is Awful Knoffel, and he claims to have been an EDC of a world famous motorcyle stunt man (this is unverified). He has a flashier costume, wearing an emerald green outfit, but he's clearly related to Gambler.

After considerable build-up to heighten the suspense, Awful Knoffel makes his leap, potentially into eternity!

Will the bungee hold? Is it too long? Will it break? Will he hit the roiling vat of coffee head first?

Thankfully it had sufficient strength and its length was correctly calculated, and Awful Knoffel survives yet another flirtation with death.

Obviously, the story is not yet finished!
John
-
LMAO! Great post!
That's us mobile
-
@ducttapetech said:
LMAO! Great post!That's us mobile
+1

-
+2....awesome!!!!!!

-
Cuppa :D "Tips" to start the day off....along with my Highlander. Recycled pic as I had to run out the door for an appointment I'm late for!!
-
@jalind said:
The Walk -- Part 3With some delay due to inability to make coffee, we proceed now with Part 3. While working the coffee maker yesterday I had it inverted draining all the water out and saw the date code. It was made in 2006, a couple months shy of ten years ago, a few years older than I had thought (it's my second Bunn of the same model).
If you recall, we had high wire failure. This has been redesigned with much stronger cable. Note the cable is now red, to prevent any inadvertent use of the old white cable, and it's anchored securely around the carafes. In addition, there were other technical challenges, such as the carafes sliding on the counter whenever there was much mass placed on the new cable, even if they were filled with water. Non-skid pads have been added under them to prevent sliding. To test its tensile strength, the Woodsman, Craftsman and Champion all volunteered to test the cable:



The cable was then tested to ensure it would not fail in hurricane force winds . . .

Finally, we have the pre-show before the main event. What daredevil event would go on without one? As the audience has once again gathered, a distant cousin of the Gambler Rambler prepares to bungee jump over the cauldron of roiling hot coffee, using a thin bungee cord around but one tool!. His stage name is Awful Knoffel, and he claims to have been an EDC of a world famous motorcyle stunt man (this is unverified). He has a flashier costume, wearing an emerald green outfit, but he's clearly related to Gambler.

After considerable build-up to heighten the suspense, Awful Knoffel makes his leap, potentially into eternity!

Will the bungee hold? Is it too long? Will it break? Will he hit the roiling vat of coffee head first?

Thankfully it had sufficient strength and its length was correctly calculated, and Awful Knoffel survives yet another flirtation with death.

Obviously, the story is not yet finished!
John
outstanding John, outstanding, bravo to your brave tools. I think you're giving Mags a run for his money here in fairness ! do we have video as well as stills ??
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

