EDC Experiments
-
I'm looking right at it, and those definitely look like 1/4" bits, not 3/8". In fact I don't think I've ever seen 3/8" bits. I found it on two other sites with the same stock description though. I think it's a typo. Those screwdriver heads would have to be massive if they were 3/8".
-
It arrives tomorrow, so I'll tell you what it is then.
-
Forgot I have the bit driver Crater too. No need to carry the bit kit.

-
Great thread, Tom.

-
Thanks!
-
Parnass, I got the bit driver in. It's definitely 1/4". It's quite a bit bigger than the Craftsman driver. Here's a comparison along with the other drivers I got in and a Wave for scale.

-
It does fit into the sheath with the Cobra where the Craftsman driver was.
-
I wish these little drivers had a hex shaft or fitting above the bit or on the end so we could put a wrench on them for more torque.
-
This is very nice thread. It even convinced me to snag a pair of Cobra pliers.
good stuff. Very lightweight -
Glad you're getting something out of it!
-
I'm favoring the Screwpop driver over the Suzo Happ and True Utility MiniDriver. It has better leverage and is nice and small. The bit is a little loose in the socket, and the magnet was out when I got it and had to be glued back in. Actually I should have left it out and used the Klein double-ended bits with their ball bearing to hold them in - probably would have worked better. The True Utility is nice and small, but you have to take out a bit to put a quarter or key in the slot on the driver to get leverage, and that will probably lead to losing bits since they are shorter than normal and black.
-
Just made my EDC sheath a lot smaller. I got in the Leatherman Piranha 2, and if this works I now have cut down my tools to a lot smaller profile by combining the crescent wrench functions, screwdriver, and prybar into one tool (actually 2 with the driver extension.)



-
Just throwing this out there for giggles: http://chapmanmfg.com/collections/new-tools/products/famous-midget-ratchet-cm-13
-
@Tom Munch said:
Just made my EDC sheath a lot smaller. I got in the Leatherman Piranha 2, and if this works I now have cut down my tools to a lot smaller profile by combining the crescent wrench functions, screwdriver, and prybar into one tool (actually 2 with the driver extension.)I forever fight the battle between "ease of carry" versus "ease of use".
-
@Tom Munch said:
for more torque.Just throwing this out there for giggles: http://chapmanmfg.com/collections/new-tools/products/famous-midget-ratchet-cm-13
Those look nice. I have a couple like that. I guess I should try them. I have the little Vic one too.
-
Just made my EDC sheath a lot smaller. I got in the Leatherman Piranha 2, and if this works I now have cut down my tools to a lot smaller profile by combining the crescent wrench functions, screwdriver, and prybar into one tool (actually 2 with the driver extension.)
I forever fight the battle between "ease of carry" versus "ease of use".
It only takes a couple seconds to snap it together, and it works better than I thought it would - easy to turn and good torque. I tried the wrench part on a couple bicycle nuts, and it worked pretty well. I was surprised.
-
Just made my EDC sheath a lot smaller. I got in the Leatherman Piranha 2, and if this works I now have cut down my tools to a lot smaller profile by combining the crescent wrench functions, screwdriver, and prybar into one tool (actually 2 with the driver extension.)
I forever fight the battle between "ease of carry" versus "ease of use".
It's fiddly but capable.
-
I did not read every post but it seems I am working on the same thing as Tom is. I carried a wave/skeletool for the last, say 10 years, and it seems I have used only some part of it frequently. Pliers, knife, screwdriver/bits. As a MT is always a compromis I am thinking of getting dedicated tools for just those three tools.
I have now the 125mm knipex cobra and plier wrench, a small combination plier, knife, screwbits and a Wera bitdriver that could fit my needs and of course something to put everything in so I am workining on a Skinth. Oh, and a flashlight have to be in that as well.
-
I've had the Knipex pair for about a week or two. I've used the pliers wrench more than anything. They are great to have. I can say they weren't on my radar until I saw this thread. Now I wouldn't want to be caught without them. How's your setup going Tom?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login