3D design progress
-
I'm on the mend pretty good now. I can walk (awkwardly) for short distances completely unaided now, and I'm improving every day. You can see all the sordid details in this thread:
/topic/64110
The short version is that it's been almost two months now, had two screws installed in my ankle and I've been passing the time largely with Netflix, 3D design and a number of random frustrations. :D
Def
-
While triangles are strong structures, the direction does matter. Also the circle one might look neat, it's probably not as strong as a triangle setup would be IMHO.
-
Probably not, but as the circular portions are roughly .5mm thick I doubt I would ever even try to print it this way. As I said, I was mostly just fiddling around.
Besides, it doesn't really require that much strength to hold a GoPro anyway, even the bigger, older Hero2's that I have. :D
Def
-
Today's project was pretty simple, even by my standards.
I use 1" square aluminum tubing as a cross bar for carrying my kayaks on my trailer. You can see them in the above photo- they are the silver bars. These are also my old ones where I had cut off the ends. I have replaced these with new ones where the ends weren't angled because this served to weaken them too much. The ends of the new set have been left raw, which is not a big deal, but I always thought that end caps would be nice. This is the kind of thing I was looking for:

Not an exciting design I know, but it was a little interesting since I added a taper to the part that gets inserted. Of course the aluminum crossbars aren't on the trailer now, and since my mobility is still somewhat limited I don't have exact measurements available so this will need some tweaking when the time comes.
On a side note, to me, these are the reasons why 3D printers are going to become common in the near future, as well as 3D scanners. We have all experienced some broken clip or fitting for some doodad or another and had no way to obtain another one. Usually the only option is to call the company and sit on hold for an hour, only to try to describe the part to someone in a call center that has never seen the device you are talking about. Then, after paying for it, you wait three weeks for it to arrive, only to find out that it's the wrong piece. I think about this a lot, specifically with regards to my parents' situation, since they live in a small town, 100 miles from the closest city. If a small part breaks, it's a long trip to make to try to find a replacement, even if it is readily available. Being able to piece the part together, scan it (or copy it manually) and have it printed out would make a world of difference for them. That is a large part of why I'm so interested in this stuff.
Def

-
I am sick of all the one piece tools on the market that are the result of people just ramming as much crap into a steel bar and trying to get rich off it, so I decided to see how difficult it is.
Here is the result of maybe an hour's worth of work, from someone who barely understands the software. Ladies and gentlemen, I give you the DefTool! :P
Def

-
Does it really need more functions than a bottle opener? :p
-
Not really. :)
Def
-
Does it come in mint chocolate chip?
-
I don't see this thing having any production in any flavor. :P
Def
-
Be careful or you might end up with a full orderbook for DefTools.
Seriously, slap a MTO logo on it and I bet there would be a queue of people here to buy one.
-
I'm sure there would be, but I think I'd rather wait until I can come up with something worth putting my name on.... you know, like I did with Uncle Def's Premium and Ultra Premium Tool Oil! :D
Last night I watched this video again (I'd seen it many times before) and I got a bit ambitious.
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
I thought that this is a project that I would really love to try sometime, although I'd rather not go with as big a boat as he did- 16' 8" is a pretty large boat. I thought I'd rather do something around the 14' mark and I started working on designing my own. I doubt this will even be what becomes the final design, I'm really just experimenting at this point. The plans for the boat above are available on the guy's website, so if I ever come to the point where I can do it I'll probably modify his design to suit my needs, but in the meantime I thought it might be fun to try my hand at designing a boat.
Def

-
I've continued working on my kayak design and I have added bulkheads, cockpit coaming and brackets for the hatch covers.
Also a slot for the rudder to fit in.
Def

-
might high tech looking tooth pick
:P -
Taking a break from the kayak project today, I decided to try one of those three way corner brackets that you use for assembling frames for things like tents. I ended up doing two different ones, both set up for 20mm diameter rods for no reason other than that's what I thought of.
The one on the left was done by making a half cube (three sides) then putting circles at the various corners and extruding them into the shared corner then deleting the cube. This worked sort of, but the junction of three round pieces seems both a bit weak to me and also seemed to upset the software greatly, so I tried to build a cube in the middle to reinforce them and fix the issues the software was having in the joint. As I was failing miserably at trying to build the cube in the middle (couldn't get the placement exactly right) it occurred to me that I was going about it backwards.
So, instead of doing the piping and then attaching the cube, I started again and created the cube first, then extruded the pipes from the cube, then cut off the corners of the cube that I didn't need in order to save print time and plastic, should it ever get printed.
The second attempt, the one on the right seems far superior to the one on the left. Live and learn, right?
Def

-
@Grant Lamontagne said:
Live and learn, right?Absolutely. There's no right or wrong way* to make a 3D model of something, but often you'll find that whatever software you're using can't do it the way you first thought - there's one method that just seems easier than all the others.
You need to get into curves and lofts fit the kayak project.

- but some methods are definitely better than others ;)
-
@Grant Lamontagne said:
Live and learn, right?
Absolutely. There's no right or wrong way* to make a 3D model of something, but often you'll find that whatever software you're using can't do it the way you first thought - there's one method that just seems easier than all the others.
You need to get into curves and lofts fit the kayak project.

- but some methods are definitely better than others ;)
Curves are definitely a problem for me at the moment. I can't seem to do anything with curves and I'm still not sure if it's a limit of the software or my abilities. I'm assuming it's me.
I did manage to locate my copy of Sketchup 8 for Dummies, and even though I'm using Sketchup 2016 it seems to be helping a lot. I still have a long bloody way to go though.
Def
-
I found this awesome gadget on eBay that allows me to keep my Surge handles closed for ONLY $12! Well, I can't afford $12 so I decided to see if I could reverse engineer it because the internet is completely free, right?
Redundancy not included.....
Def

-
I'll take 10! -
Sneaky... that other guy copied your idea then went back in time and posted it on ebay!

-
It's worse than that- he also went back in time and stole my design for the Flux Capacitor! :ahhh
Since I had Sketchup open I decided to fiddle a little bit with the DefTool design a bit more. I made it more pocketable by cutting off some corners and labeling things, because apparently that is all that is required these days to pretend something is a whole new model. :P
I also fixed the can opener so it can be used as a bottle opener as well. The current list of functions is:
Can Opener
Bottle opener
1/4" hex slot
Double ended screwdriver bit
4mm wrench
8mm wrench
12mm wrench
Prybar
Nail puller
Cutting edge
02 Wrench
Flathead/phillips screwdriverThe pill shaped slot is where the double ended screwdriver slot would fit, with a couple of rubber o rings to hold it in place. I have fallen into the trap of trying to include as many functions as I can without worrying about actually using those tools... but then unlike the "designers" that do that, I have no intention of putting this into production. :D
Def

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

