John's Unabashed STACK Challenge Thread: 2 - 31 March 2016
-
Added a cooling fan to the front of Desktop PC #3, this one to pull air in as the exhaust fans are on top and in back. The Cyber Tool 34 was made for the #2 Phillips used throughout.Access to the fan mount is through the front, behind the plastic facade which snaps to the front on the left side and hinges on the right side. First step is to get the left panel off so the front facade can be unsnapped by removing its two screws.


After the left panel has been removed, the left side of the front facade can be unsnapped, rotated open and removed to get to the front fan mounts.

The fan can be mounted to a fan housing with four screws.

Like the front faced, it's hinged on one side and remounted to the case front frame (behind the facade) with two screws. The power cable is connected to the motherboard

Front panel is hooked in and snapped back on, and then the left side is screwed back on.

Cyber Tool 34 comes through again, this time with a cyber task!
John
-
Day 29 -- 30 March 2016
I don't use my garage door opener external keypad very often. Indeed, it's rare. Attempted to use it last night and as the keypad didn't light up it was evident either the keypad battery was dead or, as has happened often in the past, weather exposure has oxidized or corroded the battery contacts, and possibly the battery terminals. Either way the battery cover has to come off. The Cyber Tool 34 bit driver's #2 Phillips is just the tool for removing the cover.

As I suspected, the battery tested OK as it's not that old, but the battery contacts are obviously oxidized causing untold resistance and voltage drop. The sharp edge on the can opener can be used to scrape and burnish the contacts, if used gently so that it's abraded and not scratched or gouged.

The other contact is oxidized and after some burnishing we're down to the bright copper on both contacts that's needed for good current flow.

A check of the battery shows it's generally clean although one of its terminals had a little crudmium on it.

Back together, it's now functioning perfectly. Need to ensure the cover is closed completely and remains closed completely as it at least slows down the battery contact oxidation. This has occurred numerous times in the past during the winter in which snow and ice have built up on the opener. It's over 20 years old, but I'm loathe to replace it so long as periodic contact burnishing keeps it working.

John
-
@jalind said:
Added a cooling fan to the front of Desktop PC #3, this one to pull air in as the exhaust fans are on top and in back. The Cyber Tool 34 was made for the #2 Phillips used throughout.Access to the fan mount is through the front, behind the plastic facade which snaps to the front on the left side and hinges on the right side. First step is to get the left panel off so the front facade can be unsnapped by removing its two screws.I don't know quite what occurs with the WYSIWYG editor which does some crazy things at times including crazy microscopic font sizes. Cannot edit it to fix it now.
Should have read:
Day 28 -- 29 March 2016
Added a cooling fan to the front of Desktop PC #3, this one to pull air in as the exhaust fans are on top and in back. The Cyber Tool 34 was made for the #2 Phillips used throughout.Access to the fan mount is through the front, behind the plastic facade which snaps to the front on the left side and hinges on the right side. First step is to get the left panel off so the front facade can be unsnapped by removing its two screws.
. . . -
Good luck on the final day

-
Day 30 -- 31 March 2016
Decided to celebrate on the last day with something that I haven't had in a long time . . . Weizenbier, or perhaps a little more correctly Hefeweizen as it's an unfiltered wheat beer. Last time I had some was long ago in Germany.

Not just to drink it, though, but to make beer bread using it, and of course, since these bottles do not have twist-off caps, the Cyber Tool 34 bottle opener is the perfect tool to use.

When I bake things, it's not just the standard recipe. Extra things to make it more interesting to the palate are added. For this beer bread, a form of quick bread (i.e. it does not use yeast to rise) I've added 4 oz of diced ham and 4 oz of grated hard sharp cheddar cheese, roughly 1 cup of each. I've learned to weigh dry ingredients as it's more accurate than volumetric measures. Afterward I was thinking about 4 oz of pineapple chunks would have been good too. Something for next time I do it with diced ham and grated cheese.

An hour later at 375 F, we have a loaf of bread, albeit it must cool before it can be removed from the stoneware bread pan and sliced. I put some grated cheese on top along with melted butter before heaving it into the oven. Here it's been sliced and I've already had two of them to test it.

It's been a fun 30 days, having to remember documenting something with the Cyber Tool 34 every day!
John
-
That's looking very good!

-
@glenfiddich1983 said:
That's looking very good!
Thanks . . . more pieces are gone now, too! Not hard to make, either. Simpler than most folks think as it's a "quick bread." Baking powder is the leavening agent instead of yeast, which eliminates the cycles of kneading and rising that yeast requires.
John
-
Great job

-
Well done John, a good month!

-
Nice thread sir, here is your badge.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

