EDC Experiments
-
Nice. I think I'll have to grab one of those.

-
Or one of these:
https://productimages.knife-depot.com/6f/8_267237.jpg
Ah I see now. Almost twice as expensive for basically the same thing :facepalm:
But I also see that there a lot utility blade based knifes out there. Another thing I have to look into :ahhh
-
Some of my tools I have

-
https://productimages.knife-depot.com/6f/8_267237.jpg
Ah I see now. Almost twice as expensive for basically the same thing

But I also see that there a lot utility blade based knifes out there. Another thing I have to look into :ahhh
Yes, there are a lot out there usually called super knives. The rubber Gerber is a little smaller, and the blade release is a little more intuitive than most and doesn't require a tool like some - you just push down on the thumb stud and pull out the blade.
-
@Tom Munch said:
Been carrying the Gerber rubber-handled utility knife for a couple days. Had to sand off some rough steel edges and added a titanium blade. Works well. I like the idea of having a blade I don't care about breaking.


I have one of these Superknives. Nice utility knife, but blade tends to slip out causing danger to your fingers when you try to cut tough material. Company i worked got four of these for us, and they all had same problem. Be very careful with these.
-
Hmmm. Thanks for the heads up. I noticed that the Stanley posted above has the same blade mechanism. I'm surprised they didn't catch it since it's a common design.
-
I like the look of the Gerber above I like the way the handle is on it
Alot of the push button ones are dangerous if you are cutting and cutting beacuse it is not hard to forget about the button and as you are cutting push it :o I have had them fall out on me before as well
Otherwise they are very dependable disposable blades :D Depedning on the brand some of the buttons are in better places than others though 
-
Carried the Gerber superknife for a few days with my tool sheath, and then I went back to a multitool when I needed less fiddling to separate out the tools - used the LM Wingman mostly. I ordered a few cheap 2 1/2" and 3" ($9-$20) dedicated folders to use with the tool sheath as an alternative to the superknife. I like using a utility blade for durability and carefree abuse, but I like a little longer blade if the knife is cheap enough to not worry about damaging or destroying it.
-
@zepla said:
I did not read every post but it seems I am working on the same thing as Tom is. I carried a wave/skeletool for the last, say 10 years, and it seems I have used only some part of it frequently. Pliers, knife, screwdriver/bits. As a MT is always a compromis I am thinking of getting dedicated tools for just those three tools.I have now the 125mm knipex cobra and plier wrench, a small combination plier, knife, screwbits and a Wera bitdriver that could fit my needs and of course something to put everything in so I am workining on a Skinth. Oh, and a flashlight have to be in that as well.
Which "combination plier, knife, screwbits" are you using?
-
Some pictures can follow sooner or later if you are interested. But I am not totally sure what to carry yet. I just recieved a Skinth to put everything in. What will fit will influence my set up. But as it looks now my kit will be:
- Gedore 125 mm combination pliers
- Wera 816R bit holder
- Some PB Swiss long shank bits that I use most (slotted and phillips in both two or three sizes)
- Spyderco H-1 Dragonfly
- Perhaps an assortment hex bits
- a very small bit ratched to use in confined spaces (like to one you'll find in a Victorinox set)
All of these can be found more or less on my Leatherman Wave but the above listed tools perform better individually. Only thing is I have to see if it does not ad up to be a much bigger package than just the Wave. An alternative for that Wera 816R could be a Wera 813R. But that is really smalll and I think I cannot aply much torque on it. Best would be something in between sizewise but I did not found anything yet that come with a fixed bit holder instead of a magnet. And I am still working what plier would be best, this combination plier that also has the cutter build in or the 125mm Cobra which has bigger opening jaws. On the other hand, bigger jaws than the Wave I hardly need to carry with me and that Gedore is about the same. Unfortunatly, there is no space for both without having to much bulk on my belt.
-
Sorry, double post.
-
Sounds good. I need to find some pictures.
-
Give me a few moments and I'll post a pictures of the stuff I mentioned.
-
I'm finding the pics too.
For my own use I need wider opening jaws. That's why a multitool doesn't work for me in a lot of situations. The Gedore does look nice though. The Wera bit holders are both good-looking too.



-
Those PB's look great!



-
You're going to have an excellent kit in all this. I may have to add a couple of these and modify my medium tool kit in my car bag. I'd like to see which Skinth you end up with and how they fit.
-
That is about the stuff indeed. Quick find!
Here is the actuall stuff on my desk:

-
It is the Skinth Plus and I have no idea how to cram it all in there :ahhh And then one of those flashlights has to come with me as well ::) And than the hex bit set is not even in that picture.
It will take some figuring out what exactly are the bare essentials and what are the "what if" stuff that you really do not need on a day to day basis. Main thing is that I do not want to have a complete toolchest on my belt.
Yeah, I know. Why don you just get yourself a nice Multitool.... ::)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login