My Juice
-
@sLaughterMed said:
Im just as frustrated as you are that he hasnt finished his mod yet yud, but this is a little passive agressive....J-screw's unfinished super juice
</topic/19553
that was not my intention, I was merely noting that the status of the thread was unfinished (the mod was finished apparently). Although I should of noted that Baja's refurb was or at least feels unfinished. Many of these are more thoughts then full on mods. -
Oh yeah one more thing about driving pins, the edge of the vice I used left deep marks in the scales, this might be fixed by putting down some leather or wood.
Now on to assembly. The pins are 1/8." As Syph mention in another thread knife kits' pivots have been slightly big, so he recommends Alpha knife supply. At any rate if your pivots are too big I chucked the pivot in the drill press and used a file and sandpaper to bring them down to size.
Assembly is pretty self explanatory, just one note make sure that the lanyard ring is placed so the notch is up when closed I made that mistake
.
So finally to my Juice. Originally the plan was add a file to the S2. But then I realized that I don't use the openers and the added spring seems to make the liner sit as to rub up against the scissors. So the can opener got dropped and the extra space was filled with the serrated blade. At some point I might try to add in a awl.


Now the much ballyhooed springs, first off you might want to hold off on the springs until the scales are on. The side springs don't want to be there and the will leave if given the chance. I fully expect to redo all four side tools before I am done.
Personally I did not find the springs that hard to do, granted that is do to Metro's pioneering work, discovered with the historiography.
I used a nail set and pushed the springs in by hand (although I did give one a tap with a hammer). Also I used a bottle opener on a SAK and a SOG can opener to move the springs from side to side. The three screwdrivers springs seem to be the easiest to place, followed by the scissors, the the blades, and the hardest seem t the Philips springs.

Well that is where the Juice DL4 stands till the post delivers my scale material.


-
Nice job Yud! did you do all that with a hand held drill?
Also, how thick is it?
-
Thanks it is a little over a half inch thick.
I used a drill press instead of handheld drill. But I think you could probably skip the drill and just use files.
The tool list:
Drill press and bits
Files
Powerlock
Sandpaper
pin punch and nail set
hammer
screw drivers -

Done, I just need some decent pictures.

-
That looks really nice.
Well done, and thank you for the detailed pics.
Cheers,
Pete
-
Nice job!
That's us mobile
-
Great job!
Whats the plan with your leftovers? Another juice mod?
-
Great job! I don't understand why LM doesn't produce more variations on the Juice line.
-
I suspect it is because the Juice line is leathermans least popular line if tools, because they are trying to compete with the same niche that SAKs already dominate. Plus, I know of only one store in the area (5th largest metropolitan area in the USA) that has any Juices (and they only have two in stock), so availability is probably an issue as well.
-
@ducttapetech said:
Nice job!That's us mobile
@sLaughterMed said:
Great job!Whats the plan with your leftovers? Another juice mod?
@rdub934 said:
Great job! I don't understand why LM doesn't produce more variations on the Juice line.@pietervn said:
That looks really nice.Well done, and thank you for the detailed pics.
Cheers,
Pete
Thank you all but I probably should of mentioned that that is an old photo. Here it is with the custom scales.


Asian water buffalo scales.
-
@sLaughterMed said:
I suspect it is because the Juice line is leathermans least popular line if tools, because they are trying to compete with the same niche that SAKs already dominate. Plus, I know of only one store in the area (5th largest metropolitan area in the USA) that has any Juices (and they only have two in stock), so availability is probably an issue as well.Leatherman have no one to blame but themselves for the Juice line not being more popular - they haven't made any meaningful changes to the line. They should add tweezers/toothpick/pin/pen to the scales and offer a pocket clip. Also, offer different tool combos, such as the one Yud created. I really like the Juice, it's well built and a very handy size.
-
@rdub934 said:
Great job! I don't understand why LM doesn't produce more variations on the Juice line.At a guess they are too expensive, for whatever reason as a result they can't compete with Vic meaning that their full potential has never been fully realized. If Vic could put the juice pliers in two 91mm frames at there normal cost I think the idea could fulfill its promise.
@sLaughterMed said:
Great job!Whats the plan with your leftovers? Another juice mod?
Not sure I don't have enough springs to make another full juice, have been thinking about a LM farmer.
-
@rdub934 said:
Leatherman have no one to blame but themselves for the Juice line not being more popular - they haven't made any meaningful changes to the line. They should add tweezers/toothpick/pin/pen to the scales and offer a pocket clip. Also, offer different tool combos, such as the one Yud created. I really like the Juice, it's well built and a very handy size.The scales on the juice just cover the skeleton of the tool, there isn't any room for any removable parts without making the tool wider. The Juice Pro however, has a plastic spacer that is used to hold a tweezers. I think there is room for more of these without widening the tool that could hold a stick pin or a tooth pick, a pen however would be a more ambitious mod, but there is some genius modders around here. I have a few other ideas for some cool juice mods, but I would need someone else to do them or have an endless supply of juices to destroy as I learn how
-
Leatherman have no one to blame but themselves for the Juice line not being more popular - they haven't made any meaningful changes to the line. They should add tweezers/toothpick/pin/pen to the scales and offer a pocket clip. Also, offer different tool combos, such as the one Yud created. I really like the Juice, it's well built and a very handy size.
The scales on the juice just cover the skeleton of the tool, there isn't any room for any removable parts without making the tool wider. The Juice Pro however, has a plastic spacer that is used to hold a tweezers. I think there is room for more of these without widening the tool that could hold a stick pin or a tooth pick, a pen however would be a more ambitious mod, but there is some genius modders around here. I have a few other ideas for some cool juice mods, but I would need someone else to do them or have an endless supply of juices to destroy as I learn how
Trust me in comparison to taking the thing apart a scale mod is easy. You just have to have the skills to cut the grooves in the scales, the bigger problem is working out what goes where.
But more to the point there is no reason that LM had to make the scales the way they did. They could of made them bigger to include scale tools or they could of added them other places. Also I don't think adding extra width to a juice is all that horrible.
-
Leatherman have no one to blame but themselves for the Juice line not being more popular - they haven't made any meaningful changes to the line. They should add tweezers/toothpick/pin/pen to the scales and offer a pocket clip. Also, offer different tool combos, such as the one Yud created. I really like the Juice, it's well built and a very handy size.
The scales on the juice just cover the skeleton of the tool, there isn't any room for any removable parts without making the tool wider. The Juice Pro however, has a plastic spacer that is used to hold a tweezers. I think there is room for more of these without widening the tool that could hold a stick pin or a tooth pick, a pen however would be a more ambitious mod, but there is some genius modders around here. I have a few other ideas for some cool juice mods, but I would need someone else to do them or have an endless supply of juices to destroy as I learn how
Trust me in comparison to taking the thing apart a scale mod is easy. You just have to have the skills to cut the grooves in the scales, the bigger problem is working out what goes where.
But more to the point there is no reason that LM had to make the scales the way they did. They could of made them bigger to include scale tools or they could of added them other places. Also I don't think adding extra width to a juice is all that horrible.
The advantage of the Juice is that it packs a lot of good sized tools in a small package. Once you get beyond the KF4 size, the advantage of the Juice becomes moot. Might as well get a Rebar once you are going that big.
-
Leatherman have no one to blame but themselves for the Juice line not being more popular - they haven't made any meaningful changes to the line. They should add tweezers/toothpick/pin/pen to the scales and offer a pocket clip. Also, offer different tool combos, such as the one Yud created. I really like the Juice, it's well built and a very handy size.
The scales on the juice just cover the skeleton of the tool, there isn't any room for any removable parts without making the tool wider. The Juice Pro however, has a plastic spacer that is used to hold a tweezers. I think there is room for more of these without widening the tool that could hold a stick pin or a tooth pick, a pen however would be a more ambitious mod, but there is some genius modders around here. I have a few other ideas for some cool juice mods, but I would need someone else to do them or have an endless supply of juices to destroy as I learn how
Trust me in comparison to taking the thing apart a scale mod is easy. You just have to have the skills to cut the grooves in the scales, the bigger problem is working out what goes where.
But more to the point there is no reason that LM had to make the scales the way they did. They could of made them bigger to include scale tools or they could of added them other places. Also I don't think adding extra width to a juice is all that horrible.
The advantage of the Juice is that it packs a lot of good sized tools in a small package. Once you get beyond the KF4 size, the advantage of the Juice becomes moot. Might as well get a Rebar once you are going that big.
I am not talking about adding that much thickness, about 1/8" to either side and you come out with the plus tool set. You might be able to trim that down even farther, with the Wenger tools. Now that does put a kf4 at about 3/4" which is not huge.
Also there is a fair amount of space in juices for the half length tools, enough for a cross cut style toothpick.
-
I suspect it is because the Juice line is leathermans least popular line if tools, because they are trying to compete with the same niche that SAKs already dominate. Plus, I know of only one store in the area (5th largest metropolitan area in the USA) that has any Juices (and they only have two in stock), so availability is probably an issue as well.
Leatherman have no one to blame but themselves for the Juice line not being more popular - they haven't made any meaningful changes to the line. They should add tweezers/toothpick/pin/pen to the scales and offer a pocket clip. Also, offer different tool combos, such as the one Yud created. I really like the Juice, it's well built and a very handy size.
Actually, I'm pretty sure the bigger problem with the Juice line is that there are too many models. There were originally five models, plus a couple of special editions, each available in two scale color variations: that's fourteen SKUs for distributors and retailers to manage. Few stores are gonna take up space in the stockroom / display case for even half of the lineup, so consumer choices are limited.
That said, I do think Leatherman's original line-up was flawed; they had two ultra-minimal models, the S2 and C2; two four-layer models, the CS4 and KF4; and the six-layer XE6, which was so thick it defeated the purpose of a smaller tool.
IMNSHO four layers is the sweet spot, not as bulky as the XE6/Pro, but with room for more functionality than the two-layer models. Yet the two models in that configuration were both poor choices for EDC. The CS4 is schizophrenic; it includes scissors and a corkscrew, typical of "suburban" EDC tools, but also a saw and awl, which are more for outdoor use. Likewise, the KF4 was poorly thought out, with not one but two knife blades, and again, a saw.
Yet for some reason Leatherman declined to make a four-layer model with the sort of implements that are expected for a suburban / office EDC tool: one knife blade, that awesome diamond-coated file, scissors, bottle/can opener. (And of course the screwdrivers, duh.) It wouldn't have been difficult: take the CS4 and replace the saw with scissors; or take the KF4 and replace the saw or serrated blade with scissors and the opener. Worse, they killed off the KF4, rather than modifying it to be more useful.
We'll never know now, of course, but personally I think a model like that would've sold well. After years of waiting for Leatherman to build it, I got tired of waiting, and made my own.
<a href="https://flic.kr/p/G72zt1" target="_blank" rel="noopener noreferrer"><img src="https://farm2.staticflickr.com/1575/26322477386_f5cc9909c8_b.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Maybe somebody at Leatherman will see the light, and make an actual EDC Juice. Maybe…
-
@Gryffin said:
IMNSHO four layers is the sweet spot, not as bulky as the XE6/Pro, but with room for more functionality than the two-layer models. Yet the two models in that configuration were both poor choices for EDC. The CS4 is schizophrenic; it includes scissors and a corkscrew, typical of "suburban" EDC tools, but also a saw and awl, which are more for outdoor use. Likewise, the KF4 was poorly thought out, with not one but two knife blades, and again, a saw.Yet for some reason Leatherman declined to make a four-layer model with the sort of implements that are expected for a suburban / office EDC tool: one knife blade, that awesome diamond-coated file, scissors, bottle/can opener. (And of course the screwdrivers, duh.) It wouldn't have been difficult: take the CS4 and replace the saw with scissors; or take the KF4 and replace the saw or serrated blade with scissors and the opener. Worse, they killed off the KF4, rather than modifying it to be more useful.
We'll never know now, of course, but personally I think a model like that would've sold well. After years of waiting for Leatherman to build it, I got tired of waiting, and made my own.
<a href="https://flic.kr/p/G72zt1" target="_blank" rel="noopener noreferrer"><img src="https://farm2.staticflickr.com/1575/26322477386_f5cc9909c8_b.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Maybe somebody at Leatherman will see the light, and make an actual EDC Juice. Maybe…
This is a sadly a very common problem that shows up in far to many models (half the market for OPTs seems to do this, cram in tools that don't compliment eachother). Not falling for this trap might be one of the best parts of models like the MUT and Signal (or the Flair for that matter).
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login