What SOG are you carrying now?
-
@ducttapetech said:
Thanks! Yeah, switching it up. As much as I love the Trident Elite, the Vulcan still reins supreme.That's us mobile
I can definitely see that! That Vulcan =

Speaking of your Trident Elite, how do you like the Tanto blade? I have two M16's now, both with tanto's, and I think I prefer a drop point, at least for an everyday, general purpose blade. I'm thinking of replacing my -10ks for a -01ks. For some reason I don't mind the tanto on my -12ze er as much, but I also don't carry it everyday like I do my -10ks
-
I love the tanto blade as an EDC blade. Very useful. Or it is on the Trident Elite. Kinda like having a regular blade but it can be used as a sheep's foot blade only you can push or pull cut. Also allows the blade to have two different edge angles. I run the tip at a steeper angle than the base. Give you a lot of options. At least for me anyways.
That's us mobile
-
@ducttapetech said:
I love the tanto blade as an EDC blade. Very useful. Or it is on the Trident Elite. Kinda like having a regular blade but it can be used as a sheep's foot blade only you can push or pull cut. Also allows the blade to have two different edge angles. I run the tip at a steeper angle than the base. Give you a lot of options. At least for me anyways.That's us mobile
Ahh, that's a good idea
I will try the same with my -10ks before I decide to replace or not. -
I love the tanto blade as an EDC blade. Very useful. Or it is on the Trident Elite. Kinda like having a regular blade but it can be used as a sheep's foot blade only you can push or pull cut. Also allows the blade to have two different edge angles. I run the tip at a steeper angle than the base. Give you a lot of options. At least for me anyways.
That's us mobile
Ahh, that's a good idea
I will try the same with my -10ks before I decide to replace or not.While I haven't done the two different angles, I noticed a huge improvement in overall cutting ability when I reprofiled my -10kz to 20 degrees on each side. I also rounded off the joint a bit between the two edges, but that was more of a personal preference.
(btw, the correct terminology is 20 degrees inclusive, right? A quick explanation would be great, if anyone wouldn't mind).
-
I love the tanto blade as an EDC blade. Very useful. Or it is on the Trident Elite. Kinda like having a regular blade but it can be used as a sheep's foot blade only you can push or pull cut. Also allows the blade to have two different edge angles. I run the tip at a steeper angle than the base. Give you a lot of options. At least for me anyways.
That's us mobile
Ahh, that's a good idea
I will try the same with my -10ks before I decide to replace or not.While I haven't done the two different angles, I noticed a huge improvement in overall cutting ability when I reprofiled my -10kz to 20 degrees on each side. I also rounded off the joint a bit between the two edges, but that was more of a personal preference.
(btw, the correct terminology is 20 degrees inclusive, right? A quick explanation would be great, if anyone wouldn't mind).
Another really good suggestion
I don't love the hard angle b/t the two edges - a little bit of rounding would be nice. I don't have a clue how I would do that, though. How did you achieve this?I would also prefer a hollow ground edge to the chisel, but it's not a deal breaker for me
-
I love the tanto blade as an EDC blade. Very useful. Or it is on the Trident Elite. Kinda like having a regular blade but it can be used as a sheep's foot blade only you can push or pull cut. Also allows the blade to have two different edge angles. I run the tip at a steeper angle than the base. Give you a lot of options. At least for me anyways.
That's us mobile
Ahh, that's a good idea
I will try the same with my -10ks before I decide to replace or not.While I haven't done the two different angles, I noticed a huge improvement in overall cutting ability when I reprofiled my -10kz to 20 degrees on each side. I also rounded off the joint a bit between the two edges, but that was more of a personal preference.
(btw, the correct terminology is 20 degrees inclusive, right? A quick explanation would be great, if anyone wouldn't mind).
Another really good suggestion
I don't love the hard angle b/t the two edges - a little bit of rounding would be nice. I don't have a clue how I would do that, though. How did you achieve this?I would also prefer a hollow ground edge to the chisel, but it's not a deal breaker for me
You have an older one with the chisel grind? You are gonna have your work cut out for you. The newer ones come with a v grind now.
I used a standard Lansky set, and spent a lot of time with the coarse 150 grit stone. If you want to do this, and if its in your budget, I really recommend you get a the diamond version of the coarse (150 grit) stone (pr even the whole diamond set). It cuts a lot faster, and will save you a lot of time.
-
That's us mobile
Nice to see the Vulcan again

-
Thanks Steve!
That's us mobile
-
-
Nice pic!
That's us mobile
-
@ducttapetech said:
Nice pic!That's us mobile
+1
-
Nice pic!
That's us mobile
+1
+2

-
FKMD-SOG PPP


-
That is a cool pic!
That's us mobile
-
@ducttapetech said:
That is a cool pic!That's us mobile
+1

-
That is a cool pic!
That's us mobile
+1

+2
-
-
Cool pic bro!
That's us mobile
-
Pocket Power Plier around the plants today



Due to the compound leverage it can easily trim and cut small flowers, branches and twigs.


Easy to clean when full of dirt and stuff, also!
-
Nice pics and nice garden.
That's us mobile
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


