And so it begins.... (My adventures into Alox!)
-
-
I feel almost as excited as you :ahhh. SOoooo close, only if you knew some real burly guys that could snatch that sucker off the floor.
-
-
Have you considered suspending the mill from the rafters and then move the stand in under it? Lifting it straight up is sure to be much easier than actually moving it in position while it's hanging.
Yes for sure that is exactly the plan.
How much does it weigh ?
A little over 400lbs.
To get my other mill on its stand I took it apart. The head and stock and table and all of it. It wasnt CNCd though and was pretty basic. No way in hell im taking this sucker apart though.
The floor joints should hold 400 lbs ok if I spring the weight out across say 4 of them. I still remember how to rig an anchor to use uneven tie in points but equally distribulte the load, so that is that I plan on doing.... tomorrow. :D
-
This is where one of those cherry engine hoists would come in handy! Provided there's enough head room..
JR -
Have you considered suspending the mill from the rafters and then move the stand in under it? Lifting it straight up is sure to be much easier than actually moving it in position while it's hanging.
Yes for sure that is exactly the plan.
How much does it weigh ?
A little over 400lbs.
To get my other mill on its stand I took it apart. The head and stock and table and all of it. It wasnt CNCd though and was pretty basic. No way in hell im taking this sucker apart though.
The floor joints should hold 400 lbs ok if I spring the weight out across say 4 of them. I still remember how to rig an anchor to use uneven tie in points but equally distribulte the load, so that is that I plan on doing.... tomorrow. :D
Just 400?
Offer beer and pizza to a few strong guys or five weak ones.
-
Ok Im going to pick up a chain hoist. This should work fine I think and its the cheapest thing I can find local to do the job.
-
The link doesn't work but if there is a harbor freight near you they may have one cheap. I don't know how close you are to the U.S. Border or if they have them in Canada.
-
@Simyo said:
The link doesn't work but if there is a harbor freight near you they may have one cheap. I don't know how close you are to the U.S. Border or if they have them in Canada.Canadian tire had a chain hoist for 60 bucks and a 1/2 ton is plenty. :D
Hoisting time
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
-
Its on!
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
-
woohoo!! Way to go! One step closer..
JR -
I'd love to see the looks on your neighbors faces when they heard the SWEARING coming from your laundry room

Congrats on getting it complete.
Now on to the good stuff.
-
Nice to see the progress! I would have recommended holding some wooden lips with a couple of clamps but you got it on in the end so it's a bit late now.
-
@Fortytwo said:
Nice to see the progress! I would have recommended holding some wooden lips with a couple of clamps but you got it on in the end so it's a bit late now.Ya if I didnt already have the mill in the air I would have made some wood squares to do the job, but its done now at least!
It fits well in the space I cleared for it too.

-
NICE!
JR -
Very nice!

P.S.: Tormach is China Made?? (in the wood box ?)
-
Nice to see the progress! I would have recommended holding some wooden lips with a couple of clamps but you got it on in the end so it's a bit late now.
Ya if I didnt already have the mill in the air I would have made some wood squares to do the job, but its done now at least!
It fits well in the space I cleared for it too.

Best laundry room in the history of clothing.
-
Here is the super popular 2 layer everyone seems to want. Note to Victorinox, you might consider this a new EDC lite model as an upgrade from the compact. Everyone hates the hook and loves the awl.
This one has a blue anodized Ti liner as well to change it up a bit from my standard brass.





And one extreme closeup to show the fit/finish and detail. That little spacer will never move from being lined up to the liner as I riveted them together with a Ti rivet. :D

-
That is freaking sick! Wow, that's like the minimal all in one! Hey here's an idea, what if you could make like a hidden tool? Idk what that new toy of yours can do, but what if you could put a file like surface on the liner, but only on the part behind the Philips? So it's kinda hidden?
JR -
Nice one Syph. One of those with the nail file hook and a fish scaler would be an ideal slim model for me.
Sent from my SM-G920R4 using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login