What did you use your Leatherman for today?
-
Used the Wave a bit today. Was pulling weeds without any gloves and after enough little stab wounds I decided the Wave would pull the rest. I also used the scissors to cut some signs down and the wood saw to trim some trees.
-
I used the Rebar's saw to prune some low tree branches and cut some brush in the backyard.
-
I used my Crunch to change the Taps (Faucet) on the kitchen sink.
Didn't need any other tools.Also I used it to adjust the chain tension on my little Kawasaki 100 - mainly to see if I could.
Crunch rules

-
I used my Rebar to twist some tie wire for use on some scaffold tags to attach them to scaffold

-
I used the ST300's straight edge blade to score the annual sticker on my license plate so that it can't be removed by criminals.
-
Rebar: Used the hard wire cutters to restring my bass. And to replace the 9v for the powered pickups. The contact had gotten adhered to the attachment.


-
The Signal's blade and hammer were used a bit today, and the Supertool's phillips was used extensively in assembling a TV stand. Also used its file to file down a section to allow another part to fit.

Sent from my SM-G920R4 using Tapatalk
-
I used the small screwdriver on the Super Tool to pry the cover off the back of my wife's watch to replace the battery. Worked like a charm!
-
Dude, you got a dell!
*anyone remember those commercials :D
-
Ha!! I sure do!!
:D -
I used the Micra's scissors to cut the tags off a pair of Crocs my youngest son got today.
-
Sadly, my only use for the poor old Wave was to file on a broken fingernail.
Sent from my Nexus 6 using Tapatalk
-
Almost, and I really mean almost used my ST300 straight blade draw and quarter a customer who provided me a test access card that was no longer active.
I wasted 2 hours Tuesday and almost that amount of time today verifying the repair work completed splicing cables.
After being allowed to review the access control computer did I find that the card was being read, but access denied because it was expired. Oh so close...Sent from my iPhone using Tapatalk
-
I used the flathead screwdrivers on my Leatherman Juice S2 to make some adjustments on my car stereo amplifiers. I seem to get the most use out of the drivers and the bits more than the pliers
Sent from my iPhone using Tapatalk
-
@LoopCutter said:
Almost, and I really mean almost used my ST300 straight blade draw and quarter a customer who provided me a test access card that was no longer active.
I wasted 2 hours Tuesday and almost that amount of time today verifying the repair work completed splicing cables.
After being allowed to review the access control computer did I find that the card was being read, but access denied because it was expired. Oh so close...Can you find a way to make them pay for all the wasted time (at double the usual rates) ? It was their fault, after all.
-
I used the Rebar's pliers to remove a broken lightbulb from a fixture in my boy's room, and later to pull some thorn bushes from a tree outside. I then used the blade to open a bag of Cheezits because I was famished from all the work I did today :D :D
-
Almost, and I really mean almost used my ST300 straight blade draw and quarter a customer who provided me a test access card that was no longer active.
I wasted 2 hours Tuesday and almost that amount of time today verifying the repair work completed splicing cables.
After being allowed to review the access control computer did I find that the card was being read, but access denied because it was expired. Oh so close...Can you find a way to make them pay for all the wasted time (at double the usual rates) ? It was their fault, after all.
Yes, at least 4 hours additional associated to wiring splice work. The quote was not prepared to account for the issue that all cables for the location passed through the gate cabinet scheduled for replacement. Some satisfaction.
-
Wound up using the Super Tool pliers and screwdriver to change out the cord on my DR Mower. I put the cord in backwards and wound up having to fish a new cord back thru.
-
The Signal's hammer and blade as well as the Supertool's phillips came in handy while assembling a new computer desk today.

Sent from my SM-G920R4 using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login