LM Signal mod
-
@tommywp said:
Can someone take some pics of the empty spaces once the plastic bits are removed and maybe give some rough dimensions? Anyone figured out an alternative use for these?Actually, just one is internal, the whistle / fire steel insert. The diamond sharpener thingie mounts on a keyhole stud on the outside:
The other insert does take up some room inside the handle, but it's an odd size:

Installed; note how the top protrudes above the handle, and the bottom follows the contour of the plier jaw
View from the inside; note the spring retainer clip on the left, that's what hold it in place
Outside, showing roughly how it's positioned when installedRemoving it doesn't really leave much empty space:

View of the handle with insert removed; not really much space at all!The only thing I can think of to put there is perhaps another insert that could hold an extra flat driver bit, but even that would be snug.
@tommywp said:
Is it uncomfortable using the tool when the spaces are left empty?Well, with the fire steel removed, the handles are smoother without it sticking out; but, the edges of the handle around the opening are kinda sharp.
The sharpener side feels less bulky, but the mounting stud is not comfortable at all.
-
Thanks gryffin. Exactly what I wanted to know.

-
Did we get an answer as to whether the Wingman scissors fit in without needing more than torx screwdrivers?

-
Just ordered an extra Wingman to do the scissors mod. Looks like it just needs a slightly larger hole like the video shows.
-
Looks like I need a better drill press and bits to drill out the pivot to the right size. All I did was heat up the scissors enough to discolor the steel and widen the hole a bit.
-
@Tom Munch said:
Looks like I need a better drill press and bits to drill out the pivot to the right size. All I did was heat up the scissors enough to discolor the steel and widen the hole a bit.I found this forum looking for info on this mod. This looks like exactly what I needed... the lack of scissors were my big complaint. Did you move the saw like he did in the video? Was that a simple mod?
-
I never got a better bit and press, so I haven't finished the mod.
-
Welcome to the forum Warren.

-
Has anyone gotten wave scissors to fit in the signal? Monrogue, did you remove the ferro rod and diamond sharpener before you dyed the yellow parts? I saw the coyote tan signal and really like the blackened plastic parts on it. Thanks for any info.
-
@Tsquare said:
Has anyone gotten wave scissors to fit in the signal? Monrogue, did you remove the ferro rod and diamond sharpener before you dyed the yellow parts? I saw the coyote tan signal and really like the blackened plastic parts on it. Thanks for any info.Not sure about the Wave scissors. I did remove the ferro rod, it just pops out. The sharpener can't be removed from the plastic part as far as I can tell, but it was unaffected by the dye anyway. The rod however will become pitted.
Sent from my SM-G920R4 using Tapatalk
-
@Tsquare said:
Has anyone gotten wave scissors to fit in the signal? Monrogue, did you remove the ferro rod and diamond sharpener before you dyed the yellow parts? I saw the coyote tan signal and really like the blackened plastic parts on it. Thanks for any info.G'Day,
I have tried, but the scissors does not work properly. When I cut something the thumb side moves past the tension spring. It MAY be because I did not tighten it properly either. Have a look at the pics. You also need to move the inner tools around.
On dying: you MUST remove the ferro rod, it starts pitting with the dye. I had to order a new one. The file is no problem. The last pic shows the pitted ferro rod.
Pete
-
Thanks to both of you. I was wondering what damage the dye might cause to either yellow tool. I like the looks of the regular signal with the matching colors. Is that a file I see on modded signal? Great job. I just love seeing all the cool creations everyone comes up with here on the forums.
-
@Tsquare said:
Thanks to both of you. I was wondering what damage the dye might cause to either yellow tool. I like the looks of the regular signal with the matching colors. Is that a file I see on modded signal? Great job. I just love seeing all the cool creations everyone comes up with here on the forums.No problem man :) Yes, he and I both put the diamond file in place of the wood saw.
Sent from my SM-G920R4 using Tapatalk
-
@Tsquare said:
Thanks to both of you. I was wondering what damage the dye might cause to either yellow tool.You are welcome. The plastic will not be damaged by the dye. It does take a fairly strong dye mixture to get the yellow bits black, and a good bit of stirring time.
Well spotted on the file, kind of an urban version for me, the OEM file is just about good enough for nails.
Cheers,
Pete
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

