What did you use your Leatherman for today?
-
I used the diamond side of the surge file to touch up my cable stripping knife after it was returned to me in less than ideal condition
. It'll do until I can sharpen it this weekend on my sharpmaker.
-
Used my sideclip and tool adapter for bike maintenance
-
I used the Rebar's wire cutters to cut the trailer seal on a big truck.
-
I used the Supertool's phillips driver while assembling another stand at our future house.
Sent from my SM-G920R4 using Tapatalk
-
PST II:
Scissors, cutting a clam pack holding some air hose fittings. Were also used to cut a plastic strap tie. Beveling the scissor arm really makes it better. In a way, with that fix, I can say they're about as good as Victorinox scissors.
Pliers--attaching a quick connect fitting to a cheap tire inflator (both included in the same set), which did not work. I finally found the 40 year old "good" tire inflator, and my grandfather and I fitted it with a Crescent wrench and a pair of Channellocks.
Handle, English ruler. To measure the width of a post, to drill holes with my Vic Soldier's awl in a 55 gallon barrel, as my grandfather wanted those holes be the width of the post apart. It turned out to be the exact width of the PST II's handle.
-
I used the pliers on my Crunch to hold a cable on the front cantilever brake on my bike while I did an adjustment.
-
Trying to fix my lighter

-
PST II: Plier head and file.
File was used to sharpen my Bear MGC Gardener's shears.
Pliers were used to remove a piece of a branch that had jammed the aforementioned shears up, but didn't work. Beating the shears against a board worked.
-
I used the small flat head on my Crunch to tighten up a loose set screw on a towel rack at my house again. I swear those things come loose when you breathe on them.
-
Yesterday (Monday) used Micra Phillips to tighten handle on crank window. Sissies to trim fibers during hose repair.
Sent from my iPhone using Tapatalk
-
Pairing up with an old Swiss to work on my father in law's motorcycle [emoji2]

Sent from my Nexus 5 using Tapatalk
-
Used my Freestyle CX to cut some tbone steak a coworker gave to me...mmmm!
-
I used my OG Supertool to fix a door at work that was stuck. It's a crash bar style exterior door, and while locking up tonight I noticed that I couldn't turn the key to release the crash bar. I used the phillips on my ST to open up the bar and see what was wrong. Nothing out of sorts, but the hook that the key moves in and out of the lock loop on the bar was stuck fast. I pulled out the medium flat head on the ST, and pried hard against the hook. It popped free after some effort. I don't think a smaller Leatherman would have worked, I was sure I was going to break the one I was using after trying a few times, but it worked out all right.
-
When opening the packaging containing a 2x25 round 10/22 magazine from Brownells, I noticed my new LM Wave is less magnetic than the PSTII I used to carry. The steel staples just dropped off the pliers. What an improvement, Leatherman

-
It's been a while since I have posted on here but I have been enjoying reading through the forum recently.
Here is what I used my Super Tool for today;
Philips to disassemble and reasemble old secateurs

File to sharpen the blade

Pliers to turn the pivot nut

Finally back together

Sent from my GT-I9300 using Tapatalk
-
Micra scissor's trimmed 3m red tape to fix a window vent shield on wife's car.
Sent from my iPhone using Tapatalk
-
@colinoutdoors said:
It's been a while since I have posted on here but I have been enjoying reading through the forum recently.Here is what I used my Super Tool for today;
Sent from my GT-I9300 using Tapatalk
Leathermans pair nicely with secateurs!



as for the thread...
I cut some wire with my ST300 today

-
Though not the biggest fan of lm bit adapter but did what needed again.

-
I used the file in my Wave to dress up the threads on a piece of all-thread I had cut with a hacksaw.
-
Used supertool saw and pe blade to cut a couple of hazel sticks so my lad and me could smash some nettles down on the local foot paths
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login