[GAW] Get your bike ready for summer!
-
@Rishard: That is a nice bike. You race a lot?
Thanks! I have never raced. I wouldn't mind doing some sort of 24 hr or 12 hr endurance type races some day when my kid is bigger and need less of my time. Right now just trying to be in some sort of shape.
How can you not race and still lose the Dolly Pardon hills sprint

We ride as a group sharing the load and then when we get to certain sections of the route like the Dolly Pardon hills it's an unannounced sprint zone and you just take off or try to catch the front guy's wheel and hang on. It's funny come to think of it unless you are a new guy and wonder what just happened.
-
Great going guys... Drawing will commence soonish, so stay tuned
-
Lets get ready...
bike pump...check
dart...check
target...check
-
Hit the target dead center on the first shot... I'm a true marksman

-
Lots of power in this little weapon. After penetrating the armor plate it got stuck at least a foot deep in the bunker wall.

-
And the winner is...
drummroll...
-
Blowgun? Ace.

Well done Fortytwo, and thanks to Etherealicer for hosting.

-
Thank you very much Etherealicer for hosting this, I'm usually not caring enough for my bike so the fact that this came up just when I had to replace the chain was just perfect! It's also been very nice seeing some bikes getting attention!

-
Looks like you had fun drawing or darting a winner. Thanks for hosting Etherealicer and a cool prize
And congratulations to Fortytwo 
-
@rishardh said:
Looks like you had fun drawing or darting a winner. Thanks for hosting Etherealicer and a cool prize
And congratulations to Fortytwo 
Hey, that is quite an effective weapon. Used it during sword sparring (without the dart), pretty much blinds the opponent at short range, long enough to impale him...
-
Congratulations fortytwo.

-
Despite this being over I'm still actually working on my bike, even without the incentive of winning something. :D
I hasten to add that I've not worked on a bike in years so if someone spots me doing something wrong please let me know, I'll not be offended in the least.
That said I'm pretty sure that the chain shouldn't be rubbing on itself when going between the two smallest cogs, so I've taken out a couple of links to get it looking like this. Still runs up and down all the gears.

-
I've also adjusted the rear breaks so as they actually line up with the rim and have looked at installing the guard for the cassette/mech.


-
@Gareth said:
That said I'm pretty sure that the chain shouldn't be rubbing on itself when going between the two smallest cogs, so I've taken out a couple of links to get it looking like this. Still runs up and down all the gears.As long as the chain is long enough so it doesn't lock up when you're on the big ring at the front and the big cog at the back, you're good.

-
@Gareth said:
I've also adjusted the rear breaks so as they actually line up with the rim and have looked at installing the guard for the cassette/mech.Make sure the front of the brake pad touches the rim a little before the rear (this is called toe-in and helps stop the brake from squealing) - use a piece of cardboard under the back of the pad to maintain the angle while you tighten the pad fixing nut. I think you've got the hardware on the brake the wrong way round - the nut should be behind the brake arm, and the pad should be in front. It's hard to tell, but I also think the pads are the wrong way round - one end is slightly longer than the other, this should be pointing towards the back of the bike.
-
That said I'm pretty sure that the chain shouldn't be rubbing on itself when going between the two smallest cogs, so I've taken out a couple of links to get it looking like this. Still runs up and down all the gears.
As long as the chain is long enough so it doesn't lock up when you're on the big ring at the front and the big cog at the back, you're good.

Checked that and is all good.

I've also adjusted the rear breaks so as they actually line up with the rim and have looked at installing the guard for the cassette/mech.
Make sure the front of the brake pad touches the rim a little before the rear (this is called toe-in and helps stop the brake from squealing) - use a piece of cardboard under the back of the pad to maintain the angle while you tighten the pad fixing nut. I think you've got the hardware on the brake the wrong way round - the nut should be behind the brake arm, and the pad should be in front. It's hard to tell, but I also think the pads are the wrong way round - one end is slightly longer than the other, this should be pointing towards the back of the bike.
I just had a fiddle with the alignment of the pads, so I'm not taking any blame for things being back to front. :D Thanks for the advice mate, I'll have another look and adjust it to suit.

-
Congrats to Fortytwo!
And thanks to Eth even if I didn't win... 
-
Gotta apologize, was real busy this week... Package will go out tomorrow
-
The price arrived today, with plenty of extra stuff! Thank you so much!
-
Glad it arrived safely... hope you like the Swiss Football team :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login