ST300 Design flaw
-
I sustained a little injury today due to what I consider a design flaw that I hadn't noticed until today.

My ST300 cut my palm when I was cutting wire. I looked at it after cleaning the blood, and I've seen



Can opener will sometimes go through the handle cutout and pierce the pocket...or your palm.
Had anybody have this happen to them before? -
Are the tools loose on that side ? On my ST 300 the can opener sits on the tab solidly.
-
That's not good. :( It might be helpful to know the date codes of any ST300's you folks are going to look at. i.e. does your ST300 have this issue and what years is it? I'm just wondering if this is something LM have addressed.
-
I did believe dull base does hit always first to casing but seems sharp edge is hitting with can opener. It is quite close to hole even with mine does not hit the hole at least easily (lands quite close to hole though). Actually looked these with vics while did a mod and parts I looked sharp edges did not hit casing. But have not looked more detailed with leathermans.
-
Here's mine:

It sits just a bit to the side. Date code is 0112. It does rest on the sharpened tip.
-
Mine is 0115, and the can opener sits firmly on the frame and could not flex toward the slit.
Pictures -
Only serrated left in with opener

View of the slit

With all tools in place

Hope clear enough and tried getting close up.Sent from my iPhone using Tapatalk
-
I have 6 different 300's kicking around (2x SS, 2x BO and 2x EOD) in various kits/locations. None of them have this issue with the can opener.
The only time I've run into this was when doing tool swaps. If you aren't careful with the layout of tools and spacers, the can opener can line up with the slot for the tab. It's pretty obvious when doing the mod, so it's never made it to the carry and use stage.
-
@Toolslinger said:
I have 6 different 300's kicking around (2x SS, 2x BO and 2x EOD) in various kits/locations. None of them have this issue with the can opener.The only time I've run into this was when doing tool swaps. If you aren't careful with the layout of tools and spacers, the can opener can line up with the slot for the tab. It's pretty obvious when doing the mod, so it's never made it to the carry and use stage.
I was just going to add that, ive noticed that this issue crops up on the Rebars as well.
If I had to guess, your tools are a little loose ThePeacent. Tightening the pivot should fix your problem.
-
I only got it to happen when the other tools are open and only then by pushing on the opener quite hard.
When they are closed I could not get it to bend into the slot; I think I am safe.<a href="http://s11.photobucket.com/user/shark_za/media/2016-01/9C62FC09-D661-4069-B9BC-96115999F6EA_zpsqgk3ofan.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i11.photobucket.com/albums/a200/shark_za/2016-01/9C62FC09-D661-4069-B9BC-96115999F6EA_zpsqgk3ofan.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
-
Finally got around to checking mine and no matter how hard I tried to push it over it wouldn't budge so I guess I am safe from this problem
Now I will have to check my Rebar since sLaughtermed said that :D -
I have st300 too. No issue like that.
Sounds like a defective unit, not a design flaw (but I see what your saying and the potential for issue although it dose t seem to be for the majority). Maybe time to use that good ol 25yr warranty

-
I checked my Rebar and when I pushed really hard it went into the notch. Under regular circumstances and use I don't forsee that it will ever happen but the possibility is there :ahhh Good to know something like this so hopefully it can be prevented for the rest of us ThePeacent

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
