And so it begins.... (My adventures into Alox!)
-
Hey glad you found my thread here and welcome to the forum!
I started doing the youtube videos more and I will take some up close video of the next parts Im making with are the little spacers under the blade tip.
Thank you for your welcome, Hi to everyone. I can't wait to see more!

Welcome aboard!

JR -
@Syph007 said:
Loving my Tormach! It was making me brass liners this morning while I had my breakfast. :D- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
How about Colossus, after the first fully programmable electronic computer?
-
Loving my Tormach! It was making me brass liners this morning while I had my breakfast. :D
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
How about Colossus, after the first fully programmable electronic computer?
Oh that's good. Or maximus. SUPER SPARTAN!
-
@MadPlumbarian said:
Welcome aboard!
JRThank you JR :-)
I would like to be able to separate the layers of a Celidor model, playing with them to know if they can be reversed, see how the tools are on springs, etc.. Can someone tell me if it's without risks to disassemble it (just drilling and remove the bushings?) after getting threaded tubes and screws?
Any advice will be welcome! ..before ordering a modded SAK ;-) -
Welcome aboard!

JRThank you JR :-)
I would like to be able to separate the layers of a Celidor model, playing with them to know if they can be reversed, see how the tools are on springs, etc.. Can someone tell me if it's without risks to disassemble it (just drilling and remove the bushings?) after getting threaded tubes and screws?
Any advice will be welcome! ..before ordering a modded SAK ;-)Hi, again. :D
You can find most of the how to's in the thread at the top of this board, convivially named SAK modding guides, all in one place. ;)
Here's the direct link to the first post that leads to other how to's.
/post/695993
As for it being easy, nope. >:D
You'll need carbide drill bits to enlarge the holes of the tools to fit your screws in. And your drill might slip and damage the scale if you're doing it on ALOX models. And you might damage or lose some of the bushings if you're doing it on Celidor models.
But where would the fun be without a bit of danger, right? :P We've all destroyed a SAK or two. Some, like Syph007 have done whole SAK massacres. :ahhh
So while you're still learning, it's best to do it on some beater SAKs, used, which you won't be sorry for if something unforeseen happens.

Happy modding.

-
@enki_ck said:
You can find most of the how to's in the thread at the top of this board, convivially named SAK modding guides, all in one place. ;)Thanks enki_ck. We meet everywhere.. :-)
Right, I realise I am off topic!

Lol SAK massacre..
I will follow the link and the guidance to try my best.Sorry for the misplaced post.
-
And the compact tinker still holding strong as most popular 2 layer 91mm now. :D
I dont think I purposely tried to show this before but the tumbled surface I do is actually highly reflective. See second last pic. So its a matte dull gray looking straight on, but at an angle very shiny.





-
NICE

JR -
So an awl on the back of the scissors layer is possible?
I presume it needs spacers?

-
@Toolslinger said:
So an awl on the back of the scissors layer is possible?I presume it needs spacers?

Yep, a washer and a tweak to the shape of the backspring.
-
So an awl on the back of the scissors layer is possible?
I presume it needs spacers?

Yep, a washer and a tweak to the shape of the backspring.
How did you do the backspring tweak?
I'm looking to build a Trail Guide but with awl behind the scissors and the fine driver on the back of the file. Only thing I haven't been able to figure out is the tension on the scissors when the awl replaces the hook.
-
So an awl on the back of the scissors layer is possible?
I presume it needs spacers?

Yep, a washer and a tweak to the shape of the backspring.
How did you do the backspring tweak?
I'm looking to build a Trail Guide but with awl behind the scissors and the fine driver on the back of the file. Only thing I haven't been able to figure out is the tension on the scissors when the awl replaces the hook.
The backspring needs to be bent about 5 degrees to give the scissors some snap close. Its a trial and error process to have the right snap. Bend it too far and the scissors have strong snap, but the awl will be a super nail breaker. Dont bend it enough and the awl will open super easy but the scissors will snap closed like a limp noodle.
-
So an awl on the back of the scissors layer is possible?
I presume it needs spacers?

Yep, a washer and a tweak to the shape of the backspring.
How did you do the backspring tweak?
I'm looking to build a Trail Guide but with awl behind the scissors and the fine driver on the back of the file. Only thing I haven't been able to figure out is the tension on the scissors when the awl replaces the hook.
The backspring needs to be bent about 5 degrees to give the scissors some snap close. Its a trial and error process to have the right snap. Bend it too far and the scissors have strong snap, but the awl will be a super nail breaker. Dont bend it enough and the awl will open super easy but the scissors will snap closed like a limp noodle.
Thanks!
Now I just need to get some time to work on it.
-
[quote author=Toolslinger link=topic=34772.msg1283843#msg1283843 date=1466037665]
So an awl on the back of the scissors layer is possible?I presume it needs spacers?

Yep, a washer and a tweak to the shape of the backspring.
How did you do the backspring tweak?
I'm looking to build a Trail Guide but with awl behind the scissors and the fine driver on the back of the file. Only thing I haven't been able to figure out is the tension on the scissors when the awl replaces the hook.
The backspring needs to be bent about 5 degrees to give the scissors some snap close. Its a trial and error process to have the right snap. Bend it too far and the scissors have strong snap, but the awl will be a super nail breaker. Dont bend it enough and the awl will open super easy but the scissors will snap closed like a limp noodle.
Thanks!
Now I just need to get some time to work on it.
[/quote]Thinking about it more, do you have any pics you could mark up to show where to bend and what to brace?
-
I finished all my brass machining, so Im working on getting flood going today so I can get onto machining the blade steels and Ti... someday I'll have this all setup I hope. :D
Enjoy me sounding like an excited little girl when I mix the coolant, and see if you notice the very dirty phrase near the end.

-
@Syph007 said:
I finished all my brass machining, so Im working on getting flood going today so I can get onto machining the blade steels and Ti... someday I'll have this all setup I hope. :DEnjoy me sounding like an excited little girl when I mix the coolant, and see if you notice the very dirty phrase near the end.

Its great you got the coolant working, but the leak is a bummer. Thankfully your a crafty man who will figure out something i'm sure. Keep us updated.

-
Whatever you do to fix it, better involve a SAK…[emoji3]
Will
-
I have heard the 'excited little girl' a few times in these videos ;)
And also the proud father!! :DMissed the dirty phrase the first time, second time I thought 'Well "darn it" is not too dirty' - Then I heard it :)
Good luck with the seal - Bit frustrating - >:( - Does it need somme sort of gasket?
-
lol,
well you got the little girl sound right, but I think we all have her when we get SOO excited, heck you should have heard me when I got my custom sak you made me, yours sounds nothing like mine, I think one of the neighbors asked who's girl we had over, I had to lie and say the little guy had one of his school friends over 
JR -
@MadPlumbarian said:
lol,
well you got the little girl sound right, but I think we all have her when we get SOO excited, heck you should have heard me when I got my custom sak you made me, yours sounds nothing like mine, I think one of the neighbors asked who's girl we had over, I had to lie and say the little guy had one of his school friends over 
JR
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login