Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Wingman clip switch

Scheduled Pinned Locked Moved The Mod Squad
17 Posts 1 Posters 3.8k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Wingman clip switch
Wingman clip switch
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Dan B Offline
    Dan B
    Posts: 149
    Dan B Offline
    Dan B
    wrote on last edited by
    #1 Quote Reply

      I figured that it would be fairly straightforward to move it to the other side and drill a hole for the peg to fit in.

      Turns out it's a little more involved than that, but still not too bad. As you can see when you remove the screw over the pocket clip, the pivot is actually a hex head faster with a threaded hole to retain the clip.

      This pivot is going to have to move over to the other side with the clip.

      IMG_20160617_153023.jpg

      IMG_20160617_153038.jpg

      Merit Badges
      Hacker
      1 Reply Last reply
      • Dan B Offline
        Dan B
        Posts: 149
        Dan B Offline
        Dan B
        wrote on last edited by Dan B
        #2 Quote Reply

          To get the pivot out I had to apply a pretty good amount of pressure to take the load of the spring off.

          Note that there are two washers: a thin bronze one for the knife and a thicker steel one for the pliers. These seem like they would be easy to loose.

          IMG_20160617_153112.jpg

          IMG_20160617_153132.jpg

          IMG_20160617_153202.jpg

          Merit Badges
          Hacker
          1 Reply Last reply
          • Dan B Offline
            Dan B
            Posts: 149
            Dan B Offline
            Dan B
            wrote on last edited by
            #3 Quote Reply

              Then I had to do the same thing on the other side.

              IMG_20160617_153236.jpg

              IMG_20160617_153252.jpg

              IMG_20160617_153325.jpg

              Merit Badges
              Hacker
              1 Reply Last reply
              • Dan B Offline
                Dan B
                Posts: 149
                Dan B Offline
                Dan B
                wrote on last edited by Dan B
                #4 Quote Reply

                  Now I reassembled it with the hex pivot on the other side. I found it easiest to line everything up with the torx wrench before trying to fit the pivot in.

                  Also, I was able to use the clip as a wrench to hold the hex side.

                  IMG_20160617_153347.jpg

                  IMG_20160617_170412.jpg

                  Merit Badges
                  Hacker
                  1 Reply Last reply
                  • Dan B Offline
                    Dan B
                    Posts: 149
                    Dan B Offline
                    Dan B
                    wrote on last edited by
                    #5 Quote Reply

                      With the hex pivot now in place could mark the spot for the hole for the clip's peg to fit into.

                      IMG_20160617_170439.jpg

                      IMG_20160617_170507.jpg

                      IMG_20160617_170525.jpg

                      Merit Badges
                      Hacker
                      1 Reply Last reply
                      • Dan B Offline
                        Dan B
                        Posts: 149
                        Dan B Offline
                        Dan B
                        wrote on last edited by
                        #6 Quote Reply

                          The peg mics out at 7/64, so I'll need at least that size of bit.

                          IMG_20160617_153055.jpg

                          Merit Badges
                          Hacker
                          1 Reply Last reply
                          • Dan B Offline
                            Dan B
                            Posts: 149
                            Dan B Offline
                            Dan B
                            wrote on last edited by Dan B
                            #7 Quote Reply

                              The drilling was tough going. I had the drill press on the slowest speed (400 rpm) and o still had to stop several times as the metal got hot.

                              I also stuffed some folded up chipboard into the middle so that it wouldn't bend and let the drill bit wander so easily

                              Finally it was done! Well, almost. The clip didn't quite sit right in it's new home.

                              IMG_20160617_170551.jpg

                              IMG_20160617_170610.jpg

                              IMG_20160617_170629.jpg

                              Merit Badges
                              Hacker
                              1 Reply Last reply
                              • Dan B Offline
                                Dan B
                                Posts: 149
                                Dan B Offline
                                Dan B
                                wrote on last edited by Dan B
                                #8 Quote Reply

                                  I used the triangle needle file to create a little more room for the peg. Now it fits great!

                                  IMG_20160617_170654.jpg

                                  IMG_20160617_171140.jpg

                                  IMG_20160617_171233.jpg

                                  IMG_20160617_171249.jpg

                                  Merit Badges
                                  Hacker
                                  1 Reply Last reply
                                  • Dan B Offline
                                    Dan B
                                    Posts: 149
                                    Dan B Offline
                                    Dan B
                                    wrote on last edited by
                                    #9 Quote Reply

                                      Just in case anyone was curious, yes the hex hole in the clip is the right size to fit 1/4" bits. I'm not sure that this would ever be that useful, but it was interesting to note.

                                      IMG_20160617_171318.jpg

                                      Merit Badges
                                      Hacker
                                      1 Reply Last reply
                                      • zoidberg Offline
                                        zoidberg
                                        Posts: 38,161
                                        zoidberg Offline
                                        zoidberg
                                        wrote on last edited by
                                        #10 Quote Reply

                                          Good work Dan. :tu: :tu:

                                          1 Reply Last reply
                                          • Dan B Offline
                                            Dan B
                                            Posts: 149
                                            Dan B Offline
                                            Dan B
                                            wrote on last edited by
                                            #11 Quote Reply

                                              @zoidberg said:
                                              Good work Dan. :tu: :tu:

                                              Thanks, zoidberg.

                                              Merit Badges
                                              Hacker
                                              1 Reply Last reply
                                              • SteveC Offline
                                                SteveC
                                                Global Moderators
                                                Posts: 72,276
                                                SteveC Offline
                                                SteveC
                                                Global Moderators
                                                wrote on last edited by
                                                #12 Quote Reply

                                                  good job :cheers:

                                                  Merit Badges
                                                  Fishing Mod User Hacker Photographer Fire Making BO Tools Level 3 Discontinued SAK/MT Challenge Traditional Folder Challenge MTo Anniversary Challenge Victorinox Spirit Challenge MTO Rotation Challenge Calendar 2019 Calendar  2018 Calendar   2017 LM Surge Challenge Level 2 The SUPER Challenge GEC Challenge LM Crunch 15 day Challenge Chili Award PST 30 Day Challenge Buck User Calendar 2020 Buck 112 Ranger 30 Day Challenge 30 Blades 30 Days Mr Pinchy Love Bites 14th Anniversary Anything Goes Challenge Buck 110 Challenge LM Rebar Challenge The 30 Day MiniTool Challenge 30 Day Locks Up Challenge 20th Anniversary Anything Goes Challenge 30 Day Barlow Challenge
                                                  1 Reply Last reply
                                                  • captain spaulding Offline
                                                    captain spaulding
                                                    Posts: 20,793
                                                    captain spaulding Offline
                                                    captain spaulding
                                                    wrote on last edited by
                                                    #13 Quote Reply

                                                      Excellent job! I hate how Leatherman puts the pocket clip on the "wrong" side (for my needs). It drives me nuts.

                                                      1 Reply Last reply
                                                      • Toolslinger Offline
                                                        Toolslinger
                                                        Posts: 2,453
                                                        Toolslinger Offline
                                                        Toolslinger
                                                        wrote on last edited by
                                                        #14 Quote Reply

                                                          Very nice! Nothing like getting a good clip setup for pocket carry.

                                                          I agree with the Captain about LM pocket clip locations. Never could figure out why it's always the wrong side... :think:

                                                          1 Reply Last reply
                                                          • LoopCutter Offline
                                                            LoopCutter
                                                            Posts: 14,395
                                                            LoopCutter Offline
                                                            LoopCutter
                                                            wrote on last edited by
                                                            #15 Quote Reply

                                                              I just carry in the left front side pocket.

                                                              Sent from my iPhone using Tapatalk

                                                              Merit Badges
                                                              Time Lord Level 2 Duct Tape Outdoor Cook The SUPER Challenge LM Rebar Challenge Chainsaw User Titanium MTo Anniversary Challenge Buck 110 Challenge Buck User MTO Rotation Challenge LM Wave Challenge LM Surge Challenge Level 3 Traditional Folder Challenge LM OHT Challenge Santa Buck 112 Ranger 30 Day Challenge Fieldmaster 30 Day Challenge Victorinox Spirit Challenge 30 Day Locks Up Challenge Fixed Blade Challenge 30 Day TWEEN Challenge - 84 and 85mm SAKs Case XX 30 Day Challenge Alox Addict Challenge PST 30 Day Challenge Spirit 60 Day Challenge 30 day 100/108mm Challenge 30 DAY OPINEL CHALLENGE LM Micra Challenge GEC Challenge Delemont 30 Day Challenge Utility Knife  30 Day Challenge Bond 30 Day Challenge MacGyver 30 Day Challenge Greenie Meanie - 30 Day Green EDC Challenge 30 Day Keychain Pliers Challenge SAK-alike Challenge SAK Range Collector Level 1 30 day Spartan Challenge Japanese PST Scale Changer I See Red - 30-Day Red EDC Challenge Tool Box Challenge Black-out EDC 30-Day Challenge 30 Day Combo Edge Challenge 30 Day Cadet Challenge 30 Day Rhymes with Orange Challenge LM Signal Challenge 20th Anniversary Anything Goes Challenge Buck 30 Day Challenge 30 Day Barlow Challenge SAK STACK Challenge 30 Days
                                                              1 Reply Last reply
                                                              • Dan B Offline
                                                                Dan B
                                                                Posts: 149
                                                                Dan B Offline
                                                                Dan B
                                                                wrote on last edited by
                                                                #16 Quote Reply

                                                                  @captain spaulding said:
                                                                  Excellent job! I hate how Leatherman puts the pocket clip on the "wrong" side (for my needs). It drives me nuts.

                                                                  @SteveC said:
                                                                  good job :cheers:

                                                                  @Toolslinger said:
                                                                  Very nice! Nothing like getting a good clip setup for pocket carry.

                                                                  I agree with the Captain about LM pocket clip locations. Never could figure out why it's always the wrong side... :think:

                                                                  Thanks, y'all. Glad you liked it.

                                                                  I've often wondered what they were thinking with those clip locations. Besides, it seems like it would have been easy enough to make it switchable by making both sides with the hex pivot.

                                                                  Unfortunately, Leatherman seem to be scared stupid about anyone tinkering with their tools.

                                                                  @LoopCutter said:
                                                                  I just carry in the left front side pocket.

                                                                  Well, that would work to at least alleviate the rotation issue.

                                                                  Merit Badges
                                                                  Hacker
                                                                  1 Reply Last reply

                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                  With your input, this post could be even better 💗

                                                                  Register Login

                                                                  1. Home
                                                                  2. Tool Talk
                                                                  3. The Mod Squad
                                                                  4. Wingman clip switch
                                                                  Reply
                                                                  • Reply as topic
                                                                  Log in to reply
                                                                  COMMUNITY LINKS
                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                  Operational Funds

                                                                  Help us keep the Unworkable working!

                                                                  Make A Donation
                                                                  November Goal: $300.00
                                                                  Due Date: Nov 30
                                                                  Total Receipts: $0.00
                                                                  Below Goal: $300.00
                                                                  0% funded
                                                                  • Login

                                                                  • Don't have an account? Register

                                                                  • Login or register to search.
                                                                  • First post
                                                                    Last post
                                                                  0