What did you use your Leatherman for today?
-
I used the phillips on my BO PST to tighten a bracket holding a fire extinguisher to the wall at work.
Sent from my SM-G920R4 using Tapatalk
-
Used Juice KF4's & Awl to install a stampede string into the new Akubra Plainsman. Pliers to push the cotter pins in through the sweatband, followed with the awl to open and spread apart the cotter pins so they could be bent across the seam. :D
Now new hat has a chin strap to combat the Idaho/Oregon winds!Also added a hat pin that's been on every hat I've worn since the late 80's. A silver Eagle that was handcrafted by a Native American, with etching on the inside: All Land, All Life. Used the KF4's pliers to align the pin in the back to the pre-punched hole, then the Awl to flip the clasp up and over the hat material to lock the hat pin in place. :D
Now to make an Emu feather hatband adornment.
-
I like the Juice KF4 in that it's light enough to do most hobby & computer work, and the awl lies flat in an lazy L shape which worked great for flipping the hat pin clasp. :D
Will show the handcrafted hat pin even though it has nothing to do with Leatherman tools. :P
-
Clearing encroaching vegetation on the local footpaths


-
Working on fence with my ST300...

Sent from my Nexus 6 using Tapatalk
-

Doing some seriously delicate untangling with the eyeglass screwdriver on my Charge TTI while watching the game
Sent from my iPhone using Tapatalk
-
nice going
-
Used my surge to make a bin liner rain coat/poncho. It's persistently raining and I got to the job 45 mins from the office and realised I'd left my raincoat in the workshop
Thankfully the guys had some bin liners in their van. Numpty of the day award today I think :D -
Used supertool pliers to re lace my work boots

-
-
I've used all my multi's as hammers...
-
Just used the scissors on my BO Wave to trim some long stragglers in my eyebrows....
LOL
Sorry, but no pics available!
Ha-ha!
Sent from my Nexus 6 using Tapatalk
-

I was looking through stuff to sell and found my Crater c33Tx, which I never much cared for and has therefore sat in a box for years. I thought it was a pity that the drivers are so ergonomic to use (being that the whole thing feels much more like a screwdriver than most MTs) but the knife is bad: the action is horrible, the centering is so off it rubs the carabiner, and the lock was over-traveling. I decided to sit down and take the thing apart to see if I could clean it up. The pivot spins, so a T6 bit is required to take off the clip first. Then two T8 bits to undo the pivot. I stopped there because I didn't want to deal with the backspring behind the drivers. I slid the top scale out of the way, and pushed the pivot pin down to liner lock. I cleaned and applied light Victorinox oil to the washers, blade, and launcher piece. Put it all back together, tightened everything appropriately, and the action was much improved. Some pivot adjustments later, and the centering was improved and the lockup was pushed back to about 80% with no play at all. This is the first time I've ever disassembled one of my knives, so I was very proud that it worked out! No longer is a flick required to get the blade out, the launcher thingy does the job easily. Suffice to say, this is going back in my pocket now, and not to auction.
-
I was looking through stuff to sell and found my Crater c33Tx, which I never much cared for and has therefore sat in a box for years. I thought it was a pity that the drivers are so ergonomic to use (being that the whole thing feels much more like a screwdriver than most MTs) but the knife is bad: the action is horrible, the centering is so off it rubs the carabiner, and the lock was over-traveling. I decided to sit down and take the thing apart to see if I could clean it up. The pivot spins, so a T6 bit is required to take off the clip first. Then two T8 bits to undo the pivot. I stopped there because I didn't want to deal with the backspring behind the drivers. I slid the top scale out of the way, and pushed the pivot pin down to liner lock. I cleaned and applied light Victorinox oil to the washers, blade, and launcher piece. Put it all back together, tightened everything appropriately, and the action was much improved. Some pivot adjustments later, and the centering was improved and the lockup was pushed back to about 80% with no play at all. This is the first time I've ever disassembled one of my knives, so I was very proud that it worked out! No longer is a flick required to get the blade out, the launcher thingy does the job easily. Suffice to say, this is going back in my pocket now, and not to auction.
Nice save!
-
I love my C33X in black. Wish it had the screw driver bits. Would then be perfect for here at work. I really have no use for a full on multitool. Even though I'm carrying my ST200 tonight. LOL
Sent from my Nexus 6 using Tapatalk
-
Used my ST200 to cut my bread and smoked sausage for dinner...

Sent from my Nexus 6 using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


