Zoidberg's Brain Surge.
-
It served well for a couple years and then I picked up the newer version.
I think months later some of it was parted.
And the new version born.
More pics are over here.
-
-
Like the new pliers idea, being snubbed and all. What did you do to keep the black oxide from burning up?
Still have the old Surge. Don't know what I could possibly do to it to get ir replaced factory wide to a newer version. One Surge is enough, especially for the the weight! Wouldn't want to buy another one unless it was a Mini-Surge-like in a Charge model or something. Of course once taking the pliers down the warranty is out the roof anyhow.
-
My First Crunch was way better than the replacement I was sent. Stupid me tried to cut the final area of a stuck stainless steel link, and my heart fell when the Crunch head broke. It did go in a "soft crunch" ... and I'm here crying, NOOOOOOOOOOOOOO!
It's replacement doesn't stay shut, the spring keeps disengaging and making it harder to deploy. Slowly trying to get used to it, though I don't hardly use it as much as I once did living on a mountain farm next to a river. It was my "go to" for priming the river pumps, getting the junk out of the river strainers, and other things. The good times. 8)
-
@Xelkos said:
My First Crunch was way better than the replacement I was sent. Stupid me tried to cut the final area of a stuck stainless steel link, and my heart fell when the Crunch head broke. It did go in a "soft crunch" ... and I'm here crying, NOOOOOOOOOOOOOO!It's replacement doesn't stay shut, the spring keeps disengaging and making it harder to deploy. Slowly trying to get used to it, though I don't hardly use it as much as I once did living on a mountain farm next to a river. It was my "go to" for priming the river pumps, getting the junk out of the river strainers, and other things. The good times. 8)
I got mine pre loved. It was also a little off and didn't stay shut etc. Hammer and nail punch took care of that though.
-
I like it. :D
Only issue I have with the Surge, least on mine, is that blade exchanger thing. Perhaps it's only on the BO versions? The older thin metal that's supposed to stay snapped over the tool holder ... that thing tends to stay in the channel when opening up. Either that or the dimple gets worn and won't stay closed.
Would so like to have an
moment to have the blade exchanger and pliers head switched to the newer version. Thing is these Surge are like indestructible! -
Noooo! Now I'll never be able to look at my old reliable Surge without thinking "I should mod this like Zoidberg's". ;)
Remember looks are not everything.
IMO, re the cutters on the different plier heads after using the Surge for months and the ST3 for weeks. Both can cut a nail in half, the ST3 will need more hand power to shear/tear through and the Surge will cut through with ease/less effort. Plier heads were tested on both sets of handles with the same results. I found that the Surge handles are more comfy and the ruler markings felt good.
I tend to carry both tools. If the job looks tool abusive I'll use the ST3 head as I can replace the cutters, otherwise I go with the Surge head for less stress on my hands.
@aussie said:
Damn you all, reading this thread i couldnt help but swap plier heads on my st300 and surge.Although i'm now left a gap when in the closed position,
is the ~blade lock/keep closed~ spring the only part that needs to be removed to provide a clean fit?
I did abit of a search but didnt find a full guide only snippets.Ah, the DaveK gap. Yes, removing the spring will provide a clean fit. I pulled up and slightly back and was able to reuse the rivets.
There is more on the handle play that is mentioned above by evil510 over here.Don't forget to post some pictures, club dark side awaits you.
I forgot to mention that if you take another pair of pliers and squeeze the handle near the pivot point, you can sneak it closer to the size you need for the SLIGHTLY thinner ST3 plier head BEFORE installation. The rest of the gap can be filled with the original bronze washers either from the ST300 or the Surge, i can't remember.
Hack on!
I have found on a couple of my Leathermen (A Surge, and a Wave) that when I disassembled the plier head from the tool, that the handle faces where the plier sits were not parallel. A quick couple of squeezes with a very large ViceGrip remedied that, and the plier pivots just slide neatly home now.
-
@Xelkos said:
It served well for a couple years and then I picked up the newer version.
I think months later some of it was parted.
And the new version born.
More pics are over here.
What is that tool it's resting on??It's it's beautiful :'( :D No really it is

-
Thank you Poncho.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login





