Metal saw for wave?
-
NKkamerus, how would I be able to get the right tension on the top pivot? I might try that idea first because I wouldn't have to modify the wave possibly. Xelkos, ideally I want the saw to fold into the tool so that I don't have it separate in my pocket.
-
Only other conceivable way would be to acquire a newer Surge, remove the blade exchanger, and modifiy the tool implement to fit the Wave/Charge model. Then you can swap out any T shank blade or the Leatherman file & saw.
-
You can also drill a hole in the bit adapter and slim down a replaceable saw/metal saw. Just need a small bolt to hold it in place ;)
-
I think tension would be fine, the wood saw would just be against the scale. Hardest part would be adjusting it so it locks every time.
Do you have more space on the opposite side?
-
@NKlamerus said:
I think tension would be fine, the wood saw would just be against the scale. Hardest part would be adjusting it so it locks every time.Do you have more space on the opposite side?
I don't think it would be able to lock either way
-
@bounding star said:
NKkamerus, how would I be able to get the right tension on the top pivot? I might try that idea first because I wouldn't have to modify the wave possibly. Xelkos, ideally I want the saw to fold into the tool so that I don't have it separate in my pocket.This is the mod he was talking about. It was done in a Charge, but the same concept will apply to the wave.
/post/1224161
-
@bounding star said:
NKkamerus, how would I be able to get the right tension on the top pivot? I might try that idea first because I wouldn't have to modify the wave possibly. Xelkos, ideally I want the saw to fold into the tool so that I don't have it separate in my pocket.
This is the mod he was talking about. It was done in a Charge, but the same concept will apply to the wave.
/post/1224161
Ahh, I see now. Didn't see a point of reference. Thanks for clearing that up, sLaughterMed
-
@Xelkos said:
@bounding star said:
NKkamerus, how would I be able to get the right tension on the top pivot? I might try that idea first because I wouldn't have to modify the wave possibly. Xelkos, ideally I want the saw to fold into the tool so that I don't have it separate in my pocket.
This is the mod he was talking about. It was done in a Charge, but the same concept will apply to the wave.
/post/1224161
Ahh, I see now. Didn't see a point of reference. Thanks for clearing that up, sLaughterMed

-
@bounding star said:
NKkamerus, how would I be able to get the right tension on the top pivot? I might try that idea first because I wouldn't have to modify the wave possibly. Xelkos, ideally I want the saw to fold into the tool so that I don't have it separate in my pocket.
This is the mod he was talking about. It was done in a Charge, but the same concept will apply to the wave.
/post/1224161
Interesting, wouldnt that make it quite flimsy?
-
@bounding star said:
@bounding star said:
NKkamerus, how would I be able to get the right tension on the top pivot? I might try that idea first because I wouldn't have to modify the wave possibly. Xelkos, ideally I want the saw to fold into the tool so that I don't have it separate in my pocket.
This is the mod he was talking about. It was done in a Charge, but the same concept will apply to the wave.
/post/1224161
Interesting, wouldnt that make it quite flimsy?
Only one way to find out...

-
Did Tofty made adapter for this? If i remember right, it is at Shapeways.
-
@sLaughterMed said:
Only one way to find out...
I'll give it a go tomorrow, ill report back asap

-
I think if you orient the teeth so it cuts on the pull stroke, it should be more durable than if the teeth were reversed. You'll definitely want to be careful not to bend the blade.
-
@Crow said:
Did Tofty made adapter for this? If i remember right, it is at Shapeways.Yep, they are here...http://www.shapeways.com/product/JVHF3S7MG/jigsaw-blade-holder-lm-wave-charge-multitools?optionId=43760888
-
This is my project, 20 min of work on a couple of blade for my surge.take a look



I've made all with dremel. hope you enjoy
-
Hi,
I was looking as well for a simple way to use a metal saw on the Wave, so I decided to make that:
The objective is to use the Wave's tool locker (file and wood saw side only), and prevent the saw from slipping with a thick layer (1.5mm) of epoxy resin on the base of a U-shank / T-shank jigsaw blade. This way the blade can be physicaly retained by the tool locker:


For T-shank type, you have 2 options:
A: original blade with epoxy, unmodified
B: blade with "ears" grinded, so it can fit a little bit more inside the Leatherman locker



Here is the blade inserted:

Hope it can help :)
-
Okay, I have shaped out a blade to go alongside the wood saw on the same pivot, but there is no way to lock it, so it is unusable. Maybe I will replace the file with the metal saw, if I can find a smaller file, maybe I can put that on my lm squirt. I might not be able to do this soon, but I will keep you updated
-
@bounding star said:
Okay, I have shaped out a blade to go alongside the wood saw on the same pivot, but there is no way to lock it, so it is unusable. Maybe I will replace the file with the metal saw, if I can find a smaller file, maybe I can put that on my lm squirt. I might not be able to do this soon, but I will keep you updatedDoes it need to lock? If it rides horizontal would that hold it?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login