Slipjoint openers
-
Nice work dks

I have several openers but they're never handy when I need them. I usually use the edge of a Penny when I need one.
-
@sparky415 said:
Maybe next time :Dand I dont even have to try....
@Spork, Lord of Lime Jello! said:
Nice work dks
I have several openers but they're never handy when I need them. I usually use the edge of a Penny when I need one.
If I had a penny I would not need to make my own openers... :D
-
Maybe next time :D
and I dont even have to try....
@Spork, Lord of Lime Jello! said:
Nice work dks
I have several openers but they're never handy when I need them. I usually use the edge of a Penny when I need one.
If I had a penny I would not need to make my own openers... :D
If you ever get very bored you can look back through some of my posts
Cut fingers :o
sanded fingers ::)
Ground fingers :-[Its funny now

-
Maybe next time :D
and I dont even have to try....
@Spork, Lord of Lime Jello! said:
Nice work dks
I have several openers but they're never handy when I need them. I usually use the edge of a Penny when I need one.
If I had a penny I would not need to make my own openers... :D
If you ever get very bored you can look back through some of my posts
Cut fingers :o
sanded fingers ::)
Ground fingers :-[Its funny now

well i found it funny at the time, wouldnt a small pair of pliers with a bit of blu tack on the end work as an opener?
-
You are always the first one to laugh when I cut something off

:D
-
IN the past I have used a medium or heavy nylon guitar pick/plectrum. Seemed to work ok, with little risk of scratching.
-
From my, definitely limited, experience I think any nail shaped material, that fits deeply and securely in the nail nick should work (I know, I am stating the obvious :D ). It should definitely be a “soft” material, so as not to scratch the knife if it slips.
I assume any material with an edge thickness of 1mm or less should be ok, for most nail nicks.
The one I made has an edge about 0.5mm thick (down from 2mm) and works fine with my small slipjoints too.
Going too thin (thin depending on the material) will make it more likely for your knife opener to break; lets not forget that you will use it on knives that could potentially break your nails as you try to open them.
What you use has to be of a reasonable length, so that it can be used comfortably.
Originally I was going to buy one of the cheap watch case openers from ebay; they seemed like they would work OK.
-
@dks said:
Some slipjoints tend to be nail breakers/extractors, even after a good cleaning (some RRs come to mind…), but for one reason or another you may not want to replace them.
Also if you like playing with slipjoints and open and close several of them in a short period of time your nails may suffer (no, I am not talking about scratched nail varnish..).So:
- Anybody use a knife opener?
Which one?
I see some RR (expensive) and Remington for sale (cheaper).
How about a watch case opener, they are quite cheap on ebay, anybody use them for knives?
Can you make one easily?
I assume it has to be made from a relatively soft metal (?) so that it will not scratch the knife if it slips.
Thank to all.

- Anybody use a knife opener?
-
I bought a Winchester one to go with my Winchester collection and to use if necessary....haven't needed it with them but it's the uncleaned TSA knives that usually break my nails....
-
I can now make one in 5 minutes, using any reasonably soft steel. I have several around the house, for any knives needing help. I really do not enjoy/need to break my nails.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login