Wiha Micro-bits and Cybertool?
-
Schah-weeet! :sak:
Thanks Terry!
-
I think there was a discussion on SOSAK about this, if I remember correctly the Whia bits would have a problem as they don't have a built in ball bearing to hold it in the Cybertool driver.
-
Ah yes, I forgot about that. Looks like I'm on the prowl for some 4mm bits with the bearing then. Thanks for reminding me about that.
-
One of the SOSAK members organised a sale of extra bits sourced from the original manufacturer a while back. The range wasn't vast but a few useful bits.
I'll see if I can find the thread, only prob is if you are not a SOSAK member you won't be able to log in and read it.
Always worth becoming a member as it's an excellent forum (like this one) :) -
Can't find it. Any other SOSAK members here remember this ?
-
I remember it, but not well. I don't remember what member was involved.
-
Off on a tangent, I wonder if it would be possible to shove a tiny rare-earth magnet into the Cybertool bit holder so the Wiha bits can be used ? ???
Worth looking into (maybe).
-
@appletree_man said:
Can't find it. Any other SOSAK members here remember this ?No chance mate, the search engine on Knife Forum's is beyond hopeless ::)
-
I think SwissBianco was the person who was selling them, so you could contact him directly. Or just post a message on SOSAK and someone will speak up...
-
Yes, it was SwissBianco. I don't recall them being cheap though, I like the sound of ATM's idea. Who's got some really powerful tiny magnets?
Neil
-
SwissBianco was selling sets of bits that included the regular ones and some of the ones from the XAVT and a couple of other odd ones.
It was around $40 for the set of 9 double-ended bits. I was also able to order an additional single bit that I had lost from my XAVT.
I have loaded up my Cybertool with alan wrench bits to replace some of the Torx, since I use them more.I found this thread on SOSAK:
http://www.knifeforums.com/forums/showtopic.php?tid/807200/post/1361067/hl/cybertool/fromsearch/1/#1361067There are a number of places that sell single-ended bits without the detent to hold them in.
Would magnetizing the bits be enough to hold them in?The Cybertool bit driver uses an odd size, but it beats out the 1/4" ones in tight spaces.
-
@AndyTiedye said:
Would magnetizing the bits be enough to hold them in?Magnets are what a lot of 1/4" bit drivers use to hold the bits in.
-
I've seen a machinist that I worked around use a neat trick with 1/4" insert bits. He would grind a shallow recess around the circumference of the bits. He would then add a o-ring to increase retention. It was a quick fix that seemed to work for him pretty well.
-
Long time lurker, finally decided to create a login, and ask a question about this subject (yes, its a thread that's 3 years old, I know)
What about putting a ball detent on the cybertool bit holder itself? It wouldn't be that hard (seriously considering doing it, as I love my cybertool 41 and carry it every day... but I'd love to have the option of carrying bits that I use, like a 1/8" hex). I don't think a strong magnet is a good option, electronics like key fobs and cell phones don't like them very much.
-
Hey, welcome!
That long driver is awesome eh?
Agree. I really wish there were more bit options. If there were, it would replace my Charge ALX as my around the farm EDC.
-
@DarthChicken said:
Long time lurker, finally decided to create a login, and ask a question about this subject (yes, its a thread that's 3 years old, I know)What about putting a ball detent on the cybertool bit holder itself? It wouldn't be that hard (seriously considering doing it, as I love my cybertool 41 and carry it every day... but I'd love to have the option of carrying bits that I use, like a 1/8" hex). I don't think a strong magnet is a good option, electronics like key fobs and cell phones don't like them very much.
That is an intriguing idea. I suppose you're suggesting one of the ball detent setups with the expanding spring-steel ring around the outside of the driver. Would this require anything other than a hole drilled in the driver for the ball, and the proper diameter spring?
-
I'm talking about a hole drilled in the side, just smaller than the diameter of a ball bearing.. toss in the ball bearing, a spring, and then plug the hole to hold the spring in place, either by tapping the hole and screwing a small plug in place, or simply peaning over the edge of the hole.
But yes, you're idea would work as well I believe, other than increasing the diameter of the tool itself a bit and having the driver sit a little higher outside the knife.
-
@DarthChicken said:
I'm talking about a hole drilled in the side, just smaller than the diameter of a ball bearing.. toss in the ball bearing, a spring, and then plug the hole to hold the spring in place, either by tapping the hole and screwing a small plug in place, or simply peaning over the edge of the hole.But yes, you're idea would work as well I believe, other than increasing the diameter of the tool itself a bit and having the driver sit a little higher outside the knife.
That would be brilliant!
-
After reading this I checked and several precision bit sets I have will fit in the cybertool socket. The most complete set I have that is sort of compatible is a 54 bit set from iFixit but I have one with ball end hex bits from Kronus as well. None of these make sets with double ended bits or ball bearings. An accessory I had not had that seems attractive for travel is the 14 bit holder at http://www.wihatools.com/700seri/751serie.htm
It is too bad that others don't make exactly compatible bits; double sided does seem like the way to go and the ball bearing works with the plastic do-hickey to hold extra bits in the cybertool.
-
@appletree_man said:
I think there was a discussion on SOSAK about this, if I remember correctly the Whia bits would have a problem as they don't have a built in ball bearing to hold it in the Cybertool driver.You might want to read this:
</post/743264>
All the bits you could ever really need, held in place too, for around $5 or $6.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
