Leatherman SIDEKICK / WINGMAN Owners Club
-
[quote author=NKlamerus link=topic=32239.msg1293576#msg1293576 date=1467253961]
[quote author=Poncho65 link=topic=32239.msg1293567#msg1293567 date=1467252726]
Sorry buddy hope you can get that clip situated
It's constantly popping out. It moves about once a day.
Can't wait to switch back to a Wave.
I bet loc-tite on that pivot would help. Also, perhaps bend the divot on the clip a little farther downward into the knife.
Done and Done
This is the only Leatherman I have actually lost. Went back to the furniture store and found the couch it was in. After that I removed the clip, added super glue, loctite, and bent the retainer down while also bending the clip as to make it hold better.
Even so the placement makes no sense!!
It does if you carry it on the left, and carry a SAK on the right
[/quote]
Not falling for that one [emoji14]
[/quote]
Oh come on.... a Climber pairs nicely with a Sidekick, and a Camper with a Wingman
-
[quote author=sLaughterMed link=topic=32239.msg1293579#msg1293579 date=1467254163]
[quote author=NKlamerus link=topic=32239.msg1293576#msg1293576 date=1467253961]
[quote author=Poncho65 link=topic=32239.msg1293567#msg1293567 date=1467252726]
Sorry buddy hope you can get that clip situated
It's constantly popping out. It moves about once a day.
Can't wait to switch back to a Wave.
I bet loc-tite on that pivot would help. Also, perhaps bend the divot on the clip a little farther downward into the knife.
Done and Done
This is the only Leatherman I have actually lost. Went back to the furniture store and found the couch it was in. After that I removed the clip, added super glue, loctite, and bent the retainer down while also bending the clip as to make it hold better.
Even so the placement makes no sense!!
It does if you carry it on the left, and carry a SAK on the right
[/quote]
Not falling for that one [emoji14]
[/quote]
Oh come on.... a Climber pairs nicely with a Sidekick, and a Camper with a Wingman
[/quote]It's true everyone knows that you need a SAK in your pocket and a LM either on your belt or clip in your pocket, rather common knowledge

-
@matt31084 said:
New to the site, just got my wingman today! I'm hoping I can relocate the belt clip and replace the two screwdrivers with the LM bit driver. Might try to replace the file with something else as well.Welcome, matt!
I did the clip switch. It's not too hard. Here is the write-up:
/post/1286449
The one additional thing that I'll say is that drilling the hole goes easier if you have some way of supporting the tool from the inside.
Oh, and please let us see the results when you're done!
-
@NKlamerus said:
Uuuuhhh
My Sidekick did this when new. I removed the clip, bent the alignment tab dealy thing down, then reattached and tightened the screw accordingly, so it was snug, but did not make the tools held by that screw too tight to open. Never loosened or came off again.
Until I misplaced the entire tool.
My Wingman has not been a problem at all.
-
Uuuuhhh

My Sidekick did this when new. I removed the clip, bent the alignment tab dealy thing down, then reattached and tightened the screw accordingly, so it was snug, but did not make the tools held by that screw too tight to open. Never loosened or came off again.
Until I misplaced the entire tool.
My Wingman has not been a problem at all.
Bad deal about the Sidekick :-\ At least you still have the Wingman though

-
Oh and welcome to
JasonJ 
-
Welcome aboard!

-
Wingman is now officially my BOB tool.

Seems versatile and basic enough for a short time emergency (lights go off, storm, foret fire) situation, so to the kit it goes.

Nice club we got here

-
I like the Wingman myself and think it is a versatile tool as well
I wished it had the PE blade like the Sidekick has but I digress ::) :DOther than that it is a very nice budget minded tool

-
I have bought my wingman not so long ago. In Russia, it is nearly $55-65 in retail.
There was a clearence of a technology market with a big 50% discount, so that I had it nearly for $30 which was a big deal for here
For knife, I have the same wish that if they could put a straight blade. But I have a plan to buy s30V blade of Charge TTI to replace with wingman's (s30V is nearly $23 here http://nalob.ru/products/20632386 )
Also, for one hand opening, I had some difficulties. So I've made a little mod on the hole of the knife blade. As you can see in the photo, I shaped a little piece of wood to fit inside the hole. Then I colored it with a permanent marker. That's it... Now much more easy to open with my thumb...
Lastly, my pliers pivot head was a little loose (I saw that some other people had similar problems with their Leatherman pliers). The pliers had a misalignment for 1-2 mm and becasue of that handles were also twisting. For solution, I took a hammer and a metal punch with a rounded edge, and then peened that pivot head in 3 different points on the circle(rivet). As a result, all that wobbling disappeared for now. Pliers had lined up again. Feels solid and better... But only some cosmetic nuance left back as you can see in the photo
(which is not important for me)



-
Great pics Neo and that is a good deal for the Wingman

Good fix of your tool as well

-
Neo, well done with the pliers, although it's a shame that you had to fix them.
I really like the wood insert as well. Is that held in by some kind of adhesive or simply press fit? Also, what kind of wood did you use?
This has me thinking of ways to make various contrasting inserts for those holes.
If you do the blade swap be sure and post it in the mod forum. I'm looking forward to seeing it.
-
@Dan B said:
Neo, well done with the pliers, although it's a shame that you had to fix them.I really like the wood insert as well. Is that held in by some kind of adhesive or simply press fit? Also, what kind of wood did you use?
This has me thinking of ways to make various contrasting inserts for those holes.
If you do the blade swap be sure and post it in the mod forum. I'm looking forward to seeing it.
Ive noticed the same issue with the blade hole and opening it can be more difficult than it should, for a oho blade imo... Trying to adjust the pivot screw can make it easier to open, but also give it blade play. So that's a good modification. I haven't tried to fix it but this is a great idea.
-
Wingman fan myself.Great tool IMPO
8)

Spring open plier head
Outside access knife & scissor tools
Pocket clip
Decent stock tool load out for the average day to day tasks , & mod-able if wanted
Good pricing NEW or used
Leatherman tough .......... & their warranty to boot
-
@Dan B said:
Neo, well done with the pliers, although it's a shame that you had to fix them.I really like the wood insert as well. Is that held in by some kind of adhesive or simply press fit? Also, what kind of wood did you use?
This has me thinking of ways to make various contrasting inserts for those holes.
If you do the blade swap be sure and post it in the mod forum. I'm looking forward to seeing it.
I had a cheap wooden 30cm ruler at home. Thickness was good for my need. Example photo:

So that, i just cut a very little piece from it with my wingmans serrated knife and then by filing with the wingman, i had a tight fit size... I was thinking to use some glue, but because of the tight fit, decided there was no need.
-
@Neo said:
So that, i just cut a very little piece from it with my wingmans serrated knife and then by filing with the wingman, i had a tight fit size... I was thinking to use some glue, but because of the tight fit, decided there was no need.Somehow it makes it just that much better that you made it using the tool that it would eventually be installed on.
-
So that, i just cut a very little piece from it with my wingmans serrated knife and then by filing with the wingman, i had a tight fit size... I was thinking to use some glue, but because of the tight fit, decided there was no need.
Somehow it makes it just that much better that you made it using the tool that it would eventually be installed on.
Yes that does make it better

-
Hi guys. I am new here. Nice to see this group.
I have had my Wingman for some time and it's just great. In the past I edc a Vic knife but it's just not enough as it doesn't carry a plier. It was OK but I had to get a new MT after my Dad took my Vic......Admit that Wingman is not the best tool and not the top quality but it is handy and great value to money. Considering I am a small built Asian, 5'7, 140lbs, even wave is too bulky for edc. Wingman is not small and not super light but it is just handy. It cannot do every work but it does most of them.
I am working as a marketing guy and 90% of my daily work is in the office. I don't actually need any excellent tools. I just need something to edc for "just in case". Wingman is excellent for that. When I have jobs that I know I need proper and serious tools, like moving in an exhibition or setting up a stage event, I'll grab my Surge. Definitely, considering my body size, edc-ing a Surge is insane but a Wingman is just good for that. Also, there are blind spots for a Surge as it cannot do very fine jobs like fixing the computer, altering your gundam figures, fixing the buckles on your wife's purse.... Do it with a surge? No way, but a wingman does. It has spring loaded pliers and loose enough to handle super fine and light jobs. Enjoy your Wingman! By the way, the scissor in Wingman is not the best but it is just right after the one in Surge. I am a scissor freak, all my tools need to carry a proper scissor.
-
@aurabattler said:
Hi guys. I am new here. Nice to see this group.
I have had my Wingman for some time and it's just great. In the past I edc a Vic knife but it's just not enough as it doesn't carry a plier. It was OK but I had to get a new MT after my Dad took my Vic......Admit that Wingman is not the best tool and not the top quality but it is handy and great value to money. Considering I am a small built Asian, 5'7, 140lbs, even wave is too bulky for edc. Wingman is not small and not super light but it is just handy. It cannot do every work but it does most of them.
I am working as a marketing guy and 90% of my daily work is in the office. I don't actually need any excellent tools. I just need something to edc for "just in case". Wingman is excellent for that. When I have jobs that I know I need proper and serious tools, like moving in an exhibition or setting up a stage event, I'll grab my Surge. Definitely, considering my body size, edc-ing a Surge is insane but a Wingman is just good for that. Also, there are blind spots for a Surge as it cannot do very fine jobs like fixing the computer, altering your gundam figures, fixing the buckles on your wife's purse.... Do it with a surge? No way, but a wingman does. It has spring loaded pliers and loose enough to handle super fine and light jobs. Enjoy your Wingman! By the way, the scissor in Wingman is not the best but it is just right after the one in Surge. I am a scissor freak, all my tools need to carry a proper scissor.
I love scissors myself and it is always good to be prepared IMO


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
