Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Dismantling Leatherman Tools(Winning The War on Knurled Knobs)

Scheduled Pinned Locked Moved The Mod Squad
53 Posts 1 Posters 21.8k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Dismantling Leatherman Tools(Winning The War on Knurled Knobs)
Dismantling Leatherman Tools(Winning The War on Knurled Knobs)
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • MultiMat Offline
    MultiMat
    Posts: 8,694
    MultiMat Offline
    MultiMat
    wrote on last edited by
    Quote Reply

      Seeing Kwakster's specialized tools got me thinking :think:. Sponny's (spoonrobot) excellent post/topic/4655 and Goldy(Goldmeister) terrific ideas in the same post proved the inspiration to me doing the modified Spoony socket. Instead of using the whack the bejeebers out of the socket with a hammer to imprint the knurled profile into the socket I have modified the Spoon process by using a vice to push the socket over the knurled fastener and thus create my own Leatherman like socket.
      To start with you need to buy a CHEAP socket set ideally a combined Metric/Imperial set.The cheap ones tend to have odd ball sizing like 5.5 & 6.5mm sockets which are ideal. My set cost $8Aus from a Automotive parts/miscellaneous junk chain store called Super Cheap.
      [(http://i291.photobucket.com/albums/ll287/multimat426/multitools/ac9c9c44.jpg)]](http://
      I also put some tape on the vices face that was going against the MT. I then lined the MT up so that the knurled fastener I wanted to get a imprint of was bang in the middle of the vice , I then secured the MT in this position with duct tape , that gives you a free hand to position the socket and turn the vice at the same time. Like this, sorry this pic is not the best.
      [(http://i291.photobucket.com/albums/ll287/multimat426/multitools/0cedafb9.jpg)]](http://
      It is important to get the initial line up as close as possible before taking the leap and tightening the vice up. I used my Fuse mostly + my PST & Micra for the process . I was surprised at the amount of force required to consummate the union. I could not detect any harm to the MT's post squeezing but I guess it is possible if you go nuts(I just went partially nuts :D) Here is the loving couple.
      [(http://i291.photobucket.com/albums/ll287/multimat426/multitools/2e3fac83.jpg)]](http://
      Here is one of the two Micra sockets.
      [(http://i291.photobucket.com/albums/ll287/multimat426/multitools/1123ee29.jpg)]](http://
      OK. THE PROS ; they work , my LM's will not get damaged(can happen with vice grips) , I do not need to wait for Kwakster's tools to make it to OZ, cheap to make .
      THE CONS ; If you use good quality sockets (ie hard) you can Roger the fastener and not have a mod tool.I tried a Sidecrome(Australian tool making institution) & this happened
      [(http://i291.photobucket.com/albums/ll287/multimat426/multitools/12619a69.jpg)]](http://![)
      Interestingly this great Australian socket was made in Taiwan >:(
      Given you have to use softer sockets I do not know how long they will last :think:
      In my quest to make a spanner like tool I went a bit silly and my vice went, Snap , Crackle & Fu#ked :- :(
      [(http://i291.photobucket.com/albums/ll287/multimat426/multitools/4c11f898.jpg)]

      I tried Spoony method & just could not get the socket to sit when hitting it with the hammer . I tried making the socket red hot & hitting it with a hammer & no luck.I tried using a G clamp with marginal success(socket tended to slip & then spin >:( ). This method does work ,I would be interested to hear how people go if they chose to give this way a go. Thanks to Spoonrobot & Goldmeister for their good ideas.

      1 Reply Last reply
      • max6166 Offline
        max6166
        Posts: 1,547
        max6166 Offline
        max6166
        wrote on last edited by
        #1 Quote Reply

          Excellent! :salute: :cheers:

          1 Reply Last reply
          • Mike, Lord of the Spammers! Offline
            Mike, Lord of the Spammers!
            Posts: 42,975
            Mike, Lord of the Spammers! Offline
            Mike, Lord of the Spammers!
            wrote on last edited by
            #2 Quote Reply

              Great tutorial mate :cheers:

              1 Reply Last reply
              • DaveK Offline
                DaveK
                Posts: 13,379
                DaveK Offline
                DaveK
                wrote on last edited by
                #3 Quote Reply

                  Good work Mat - I must have a go at this sometime.

                  1 Reply Last reply
                  • max6166 Offline
                    max6166
                    Posts: 1,547
                    max6166 Offline
                    max6166
                    wrote on last edited by
                    #4 Quote Reply

                      You know, bashing the knurled heads into a regular hex shape isn't such a bad idea either...

                      1 Reply Last reply
                      • Sea Monster Offline
                        Sea Monster
                        Posts: 4,261
                        Sea Monster Offline
                        Sea Monster
                        wrote on last edited by
                        #5 Quote Reply

                          Sidecrome(Australian tool making institution)

                          Until they were bought out by Stanley and they started making tools in taiwan.

                          I'm off to by a SupaTool set from the auto store!

                          1 Reply Last reply
                          • Poncho65 Offline
                            Poncho65
                            Global Moderators
                            Posts: 87,638
                            Poncho65 Offline
                            Poncho65
                            Global Moderators
                            wrote on last edited by
                            #6 Quote Reply

                              Great job MM :cheers: :cheers: :cheers: The pics look of fine quality to me ;) I am gonna have to get some cheap bit and try this myself :o :D :D :D

                              Merit Badges
                              BO Tools Level 2 Japanese PST Reviewer Photographer Axe User Fire Making Hacker Multitool Encyclopedia User OCD Squad Time Lord Level 1 Mod User Duct Tape Discontinued SAK/MT Challenge The SUPER Challenge EDC Pocket Dump Challenge Def's 50k Challenge LM Rebar Challenge Traditional Folder Challenge Gerber MP Challenge Modified SAK Challenge MTo Anniversary Challenge Victorinox SwissTool Challenge LM Surge Challenge Level 2 Victorinox Spirit Challenge MTO Rotation Challenge LM Wave Challenge Calendar   2017 Calendar  2018 Calendar 2019 LM Surge Challenge Level 3 Keychain Challenge LM Crunch 15 day Challenge LM OHT Challenge PST 30 Day Challenge Calendar 2020 14th Anniversary Anything Goes Challenge Skeletool 30 Day Challenge The Batman 30 Day Challenge Poker Face Challenge Daredevil challenge The 30 Day MiniTool Challenge 30 Day Locks Up Challenge One Piece Collector 30 Day Rhymes with Orange Challenge Bond 30 Day Challenge Wally Badge 30 Day Ratchet Challenge
                              1 Reply Last reply
                              • Anthony Offline
                                Anthony
                                Posts: 3,994
                                Anthony Offline
                                Anthony
                                wrote on last edited by
                                #7 Quote Reply

                                  Alright, lets see what type of odd fastener Leatherman comes out with next to thwart us!

                                  This thread makes me wish I didn't sell my Blast and Kick :(

                                  1 Reply Last reply
                                  • J-sews Offline
                                    J-sews
                                    Admin Team
                                    Posts: 23,224
                                    J-sews Offline
                                    J-sews
                                    Admin Team
                                    wrote on last edited by
                                    #8 Quote Reply

                                      Great bit of work there Mat! :cheers:

                                      @max6166 said:
                                      You know, bashing the knurled heads into a regular hex shape isn't such a bad idea either...

                                      Hehe, that's funny :D

                                      1 Reply Last reply
                                      • MultiMat Offline
                                        MultiMat
                                        Posts: 8,694
                                        MultiMat Offline
                                        MultiMat
                                        wrote on last edited by
                                        #9 Quote Reply

                                          Add it , I have found if the knurled imprint is not perfect you can file the socket down & give it another go(Surge's file worked well). It is easy to go too quick and bugger it up . So the best way is go slow :D.

                                          PS ideas on getting the broken bolt shafts out of my vice so I can put new bolts in. I was thinking of using my dad's drill press & using something like Eazy outs? I have not used this before any tips ? It is funny I have had that vice for 3 years & not really used it much until I needed to make these sockets & decided to finally mount it properly under a week ago ::) :D

                                          1 Reply Last reply
                                          • jzmtl Offline
                                            jzmtl
                                            Posts: 8,551
                                            jzmtl Offline
                                            jzmtl
                                            wrote on last edited by
                                            #10 Quote Reply

                                              If you need soft sockets, heat one up till magnet doesn't stick then throw it in some non-flammable insulator and let it cool down slowly.

                                              1 Reply Last reply
                                              • J-sews Offline
                                                J-sews
                                                Admin Team
                                                Posts: 23,224
                                                J-sews Offline
                                                J-sews
                                                Admin Team
                                                wrote on last edited by
                                                #11 Quote Reply

                                                  @MultiMat said:
                                                  Add it , I have found if the knurled imprint is not perfect you can file the socket down & give it another go(Surge's file worked well). It is easy to go too quick and bugger it up . So the best way is go slow :D.

                                                  PS ideas on getting the broken bolt shafts out of my vice so I can put new bolts in. I was thinking of using my dad's drill press & using something like Eazy outs? I have not used this before any tips ? It is funny I have had that vice for 3 years & not really used it much until I needed to make these sockets & decided to finally mount it properly under a week ago ::) :D

                                                  You'll be needing to use eazy outs on that vice Mat. Generally they are sold as a 3-piece or 5-piece set. Even better would be if you could borrow a set from someone, as you are unlikely to use them very often.

                                                  1 Reply Last reply
                                                  • MultiMat Offline
                                                    MultiMat
                                                    Posts: 8,694
                                                    MultiMat Offline
                                                    MultiMat
                                                    wrote on last edited by
                                                    #12 Quote Reply

                                                      Thanks Bob , my research tells me cheap stud removers are not great for the job & like you said I probably will not need the kit ever again so buying a expensive kit not good sense . Now who do I know who might have some :think:

                                                      1 Reply Last reply
                                                      • detron Offline
                                                        detron
                                                        Posts: 7,546
                                                        detron Offline
                                                        detron
                                                        wrote on last edited by
                                                        #13 Quote Reply

                                                          THREAD NECRO!

                                                          this is very nice

                                                          Merit Badges
                                                          Hacker EDCSource Buyer Time Lord Level 3 Paracord MTO Tool Scaler User Hook User Scale Changer OCD Squad
                                                          1 Reply Last reply
                                                          • Nhoj Offline
                                                            Nhoj
                                                            Posts: 2,791
                                                            Nhoj Offline
                                                            Nhoj
                                                            wrote on last edited by
                                                            #14 Quote Reply

                                                              I remember reading this awhile back. Useful information.

                                                              1 Reply Last reply
                                                              • detron Offline
                                                                detron
                                                                Posts: 7,546
                                                                detron Offline
                                                                detron
                                                                wrote on last edited by
                                                                #15 Quote Reply

                                                                  I bought 2 sets of "testing" sockets. these are the pinnacle Dollar Tree tools :facepalm:

                                                                  if these are not soft enough, then I do not know what is. it was $1.00 :rofl:

                                                                  Merit Badges
                                                                  Hacker EDCSource Buyer Time Lord Level 3 Paracord MTO Tool Scaler User Hook User Scale Changer OCD Squad
                                                                  1 Reply Last reply
                                                                  • MultiMat Offline
                                                                    MultiMat
                                                                    Posts: 8,694
                                                                    MultiMat Offline
                                                                    MultiMat
                                                                    wrote on last edited by
                                                                    #16 Quote Reply

                                                                      Good luck mate :D :D

                                                                      1 Reply Last reply
                                                                      • detron Offline
                                                                        detron
                                                                        Posts: 7,546
                                                                        detron Offline
                                                                        detron
                                                                        wrote on last edited by
                                                                        #17 Quote Reply

                                                                          @MultiMat said:
                                                                          Good luck mate :D :D

                                                                          thanks! I am excited to try this

                                                                          Merit Badges
                                                                          Hacker EDCSource Buyer Time Lord Level 3 Paracord MTO Tool Scaler User Hook User Scale Changer OCD Squad
                                                                          1 Reply Last reply
                                                                          • zoidberg Offline
                                                                            zoidberg
                                                                            Posts: 38,161
                                                                            zoidberg Offline
                                                                            zoidberg
                                                                            wrote on last edited by
                                                                            #18 Quote Reply

                                                                              I like the marred fasteners, it gives it character. Really though, I should try and make some of these.

                                                                              1 Reply Last reply
                                                                              • detron Offline
                                                                                detron
                                                                                Posts: 7,546
                                                                                detron Offline
                                                                                detron
                                                                                wrote on last edited by
                                                                                #19 Quote Reply

                                                                                  I am just too cheap to buy the Vampliers for the cost of two of those, I could buy another MT or SAK ::)

                                                                                  Merit Badges
                                                                                  Hacker EDCSource Buyer Time Lord Level 3 Paracord MTO Tool Scaler User Hook User Scale Changer OCD Squad
                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 3
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. The Mod Squad
                                                                                  4. Dismantling Leatherman Tools(Winning The War on Knurled Knobs)
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0