And so it begins.... (My adventures into Alox!)
-
Playing around this morning with the diamond engraver. :D
-
Nice smurfing job :D

-
Nice little Piece of Smurf - Syph >:D :D
I agree that the image is a little complex for the size - the diagram on the screen did not look too good - However on the blade it looks pretty good!!
@Syph007 said:
Here are the other things I tried:- Machine press fit ring to hold it it. Fail as it wastes more brass sheet, more machine time and didnt look good.
- Crazy glue - Really sucked as I could never keep it from being visible at the edges.
- Clear silicone - Same problem as glue
- Machine tabs to hold it in - Worked but had the effect of making the glass look non round so esthetic fail and also more machine time.
- Machine oversize ring to then screw over top. Way more machine time and then I need screws and drilling and tapping.. yuck
- Machine 2 thinner versions each with a lip then sandwich them. Double machine time, more material used, and a seam down the center....
Gosh - How many hours work and wasted parts is all that ?? Especially if you include version 1 with the screw!!
I know exactly what you mean about looking for the complex solution when there is a really simple one - I am doing this all the time - at home and work!!
As always - I'm in total admiration of your perseverence, ingenuity and complete commitment to doing a top quality job! You will stop short of nothing less than excellence!PS. Noticed the bite on you finger right at the beginning of the vid :o
-
That was pretty awesome

-
@Huntsman said:
Nice little Piece of Smurf - Syph >:D :DI agree that the image is a little complex for the size - the diagram on the screen did not look too good - However on the blade it looks pretty good!!
Here are the other things I tried:
- Machine press fit ring to hold it it. Fail as it wastes more brass sheet, more machine time and didnt look good.
- Crazy glue - Really sucked as I could never keep it from being visible at the edges.
- Clear silicone - Same problem as glue
- Machine tabs to hold it in - Worked but had the effect of making the glass look non round so esthetic fail and also more machine time.
- Machine oversize ring to then screw over top. Way more machine time and then I need screws and drilling and tapping.. yuck
- Machine 2 thinner versions each with a lip then sandwich them. Double machine time, more material used, and a seam down the center....
Gosh - How many hours work and wasted parts is all that ?? Especially if you include version 1 with the screw!!
I know exactly what you mean about looking for the complex solution when there is a really simple one - I am doing this all the time - at home and work!!
As always - I'm in total admiration of your perseverence, ingenuity and complete commitment to doing a top quality job! You will stop short of nothing less than excellence!PS. Noticed the bite on you finger right at the beginning of the vid :o
It looks really good in person. Was mostly a test of the engraver I was after anyhow. :D
Ive got quite a few wounds at the moment. Opened up my middle finger today with a nice sharp SAK blade and introduced my thumb to a slitting saw a few days ago. When I finally get done the R&D phase for 91mm my fingers can rest up. :D I was going to move to 93 next but the 84mm demand is still pretty high so I might as well tackel that next and have some CNC fixtures for doing that backspring hack to fit scissors on there. A skeletonized 84mm Ti handle would be super light.
-
Nice little Piece of Smurf - Syph >:D :D
I agree that the image is a little complex for the size - the diagram on the screen did not look too good - However on the blade it looks pretty good!!
Here are the other things I tried:
- Machine press fit ring to hold it it. Fail as it wastes more brass sheet, more machine time and didnt look good.
- Crazy glue - Really sucked as I could never keep it from being visible at the edges.
- Clear silicone - Same problem as glue
- Machine tabs to hold it in - Worked but had the effect of making the glass look non round so esthetic fail and also more machine time.
- Machine oversize ring to then screw over top. Way more machine time and then I need screws and drilling and tapping.. yuck
- Machine 2 thinner versions each with a lip then sandwich them. Double machine time, more material used, and a seam down the center....
Gosh - How many hours work and wasted parts is all that ?? Especially if you include version 1 with the screw!!
I know exactly what you mean about looking for the complex solution when there is a really simple one - I am doing this all the time - at home and work!!
As always - I'm in total admiration of your perseverence, ingenuity and complete commitment to doing a top quality job! You will stop short of nothing less than excellence!PS. Noticed the bite on you finger right at the beginning of the vid :o
It looks really good in person. Was mostly a test of the engraver I was after anyhow. :D
Ive got quite a few wounds at the moment. Opened up my middle finger today with a nice sharp SAK blade and introduced my thumb to a slitting saw a few days ago. When I finally get done the R&D phase for 91mm my fingers can rest up. :D I was going to move to 93 next but the 84mm demand is still pretty high so I might as well tackel that next and have some CNC fixtures for doing that backspring hack to fit scissors on there. A skeletonized 84mm Ti handle would be super light.
Someone was saying that a person needs to use gloves when using a MT or knife the other day on here

-
Nice little Piece of Smurf - Syph >:D :D
I agree that the image is a little complex for the size - the diagram on the screen did not look too good - However on the blade it looks pretty good!!
Here are the other things I tried:
- Machine press fit ring to hold it it. Fail as it wastes more brass sheet, more machine time and didnt look good.
- Crazy glue - Really sucked as I could never keep it from being visible at the edges.
- Clear silicone - Same problem as glue
- Machine tabs to hold it in - Worked but had the effect of making the glass look non round so esthetic fail and also more machine time.
- Machine oversize ring to then screw over top. Way more machine time and then I need screws and drilling and tapping.. yuck
- Machine 2 thinner versions each with a lip then sandwich them. Double machine time, more material used, and a seam down the center....
Gosh - How many hours work and wasted parts is all that ?? Especially if you include version 1 with the screw!!
I know exactly what you mean about looking for the complex solution when there is a really simple one - I am doing this all the time - at home and work!!
As always - I'm in total admiration of your perseverence, ingenuity and complete commitment to doing a top quality job! You will stop short of nothing less than excellence!PS. Noticed the bite on you finger right at the beginning of the vid :o
It looks really good in person. Was mostly a test of the engraver I was after anyhow. :D
Ive got quite a few wounds at the moment. Opened up my middle finger today with a nice sharp SAK blade and introduced my thumb to a slitting saw a few days ago. When I finally get done the R&D phase for 91mm my fingers can rest up. :D I was going to move to 93 next but the 84mm demand is still pretty high so I might as well tackel that next and have some CNC fixtures for doing that backspring hack to fit scissors on there. A skeletonized 84mm Ti handle would be super light.
I'm in for another 84 mm this time I'll send you parts for bladeless 84 mm Ti. [emoji5]
Sent from my E6653 using Tapatalk
-
-
Someone was saying that a person needs to use gloves when using a MT or knife the other day on here

Hmmm - So he was right after all !!
???
... Especially when around Kevin Davey's mum!! :oEspecially around Kevin's mom :o :ahhh :ahhh :ahhh May need a suit of armor as well :D
-
After stuggling today to cut up some stock material I had enough and ordered a band saw. I managed this long witout one, but I cant take it any more. :D
It's little but will do the job I need.

-
Dang, I have a small hand one, I almost bought the base that turned it into what you got, but that was more then the freaking saw, just gotta know how to work it.. Looking good syph!
JR -
Textured and tumbled finish Ti marlin spike model going together today. :D
Ive had these cut for awhile waiting for the customer to give the go ahead.

-
Love it soo much [emoji8][emoji8][emoji8]
Sent from my iPhone using Tapatalk
-
And... here we go...







-
very nice

-
So many ideas

I love these pics and updates Syph

-
Nice spike!

How about a monster awl? :D -
So, when are you ready to make some blue anodized 93mm OC Ti scales? I'm ready whenever you are! :D
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login