Show off your Sak mod's!
-
@Wade Eva said:
Built this one last month. It's my take on a Farmer X. It's a SPECIAL one.Can you figure out what makes this one so SPECIAL? ;)
(Please excuse the dirty knife. Just pulled it from my pocket to shoot.)
Very nice [emoji8]☕️
Sent from my iPhone using Tapatalk
-
+1
-
@Wade Eva said:
Built this one last month. It's my take on a Farmer X. It's a SPECIAL one.Can you figure out what makes this one so SPECIAL? ;)
What doesn't make it special? So much niceness... even if it did apparently wake up with a bit of a hangover and put on 2 left shoes :)
Nice brass liners, and is that a brass spacer/keyring loop as well? Nice rivetting work, it must take a bit of courage to swing the hammer at an expensive red scale.
-
@Wade Eva said:
Built this one last month. It's my take on a Farmer X. It's a SPECIAL one.
Can you figure out what makes this one so SPECIAL? ;)
What doesn't make it special? So much niceness... even if it did apparently wake up with a bit of a hangover and put on 2 left shoes :)
Nice brass liners, and is that a brass spacer/keyring loop as well? Nice rivetting work, it must take a bit of courage to swing the hammer at an expensive red scale.
Exactly, the combo of scissors, brass liners, kooky crazy mismatched scales, and what I think is a genuine Victorinox clip? together the combo gives off "custom" along with a hint of vintage militaria kind of a feel. The patina would go nice with a worn drab canvas sheath.
It's kind of like certain types of muscle car builds, deliberate use of a primer-only finish but fancy engine, etc...certainly not off the shelf...BUT ALSO...in terms of functionality...sweet spot between size and number of implements, and an all metal build always feels like you can jump out of a helicopter with it. And this might sound weird but I like the peening, like the amount of facets vs smooth dome surface...and I like that you didn't go with torx for this look. Basically it looks hand hammered as if this is a 40's military item. .I always overlook scuffed up colored alox knives on ebay thinking I would want plain aluminum so the scuffs don't show...but when you do everything else rebuilt and clean, then they're like $400 ripped up rock'n'roll jeans. This would go nice with one of them silly right-angle flashlights with maybe an amber lens in it. Aluminum boyscout canteen...all set. And if you do drop it on the rocks...it's whatever. But you won't drop it cuz of that clip....
-
I know these guts posts aren't pretty but..technically it's showing off my mod right?
My plan to put the finer inline phillips (from 111mm Outrider) across from standard inline philips has been replaced with the notion of mounting it across from a nail file (from Sportsman) using a blades-layer spring...
The fine phillips is the thickness of scissors, looks to me that the blade spring is very very close to the same thickness.
I would use a liner WITHOUT the raised section for contemporary/thinner main blades, but instead a flat liner, so the phillips can take up the full thickness of the layer, and of course the spacer for the nail file...
This would allow large and pen blades in one layer then nailfile and fine phillips in another. But also there's the dilema of the rear tool, I'm guessing multipurpose hook, corckscrew and backside phillips are the only ones of (near)correct thickness.
Anybody know if something off the 58mm or 74mm knives would be the correct thickness to use as the backside tool? If not, are there any 91mm blade-layer springs without a back tool, like some 84mm models have?
It looks tight but it looks like it might close up perfectly...(less "rigged" than my previous idea)....I don't have a spare nail file so I'm mocking it up here with a small blade and the wrong liner...I think the nail file isn't as wide as the blade, perhaps leaving slightly more room for the phillips.

-
Thanks for the complements guys! Much appreciated.
What makes this one so SPECIAL is...............................
that I messed up and put the saw and scissors on the wrong sides. So the nail nick for the scissors is behind the saw! It's still accessible due to the bendy nature of the saw, but still! ::)
Anyway, it's my EDC and I really love it. I have and extra Cutlery Shopp Blue Farmer that's up next. Just need to make liners.
I can do smooth peened pins, but I like the hammered look. Just gives it some character. And yes, the key ring loop/spacer is brass.
The pocket dangler (clip) is home made. Stainless Steel baby spoon gave up the ghost for this one!
And the added benefit is that with the left over parts, I make a two toned Pioneer.
Finally, thanks to all the contributors to this site/forum. The wealth of knowledge is second to none and the professionalism is above par.
-
The wood is beautiful
Love how simple and elegant it is 
That's what she said...



-
Minichamp autopsy for reference... In case anyone needs it...

Sent from my iPhone using Tapatalk
-
@jaya_man said:
Minichamp autopsy for reference... In case anyone needs it...

So I've been meaning to ask, after seeing the small magnetic phillips/can opener combo tool from mini champ/etc used as back side tool on 91mm knife...can the tools from the back of 91mm knives, aside from corkscrew and phillips, but mounted in a mini champ chassis?
-
Syph has put an awl on a 58mm:
@Syph007 said:
The other was to have the awl from a 91mm replace the cuticle pusher / ruler layer.The awl actually fits really well. I filled the original 2.5mm hole with brass and re-drilled a 1/16th inch hole for the right spot for a 58mm hole. In this super up close pic you can see what I mean.




This is just a test setup to see if the awl works and it does. Snap is perfect. The only other thing it needed was a very very did I say very, tiny washer that is 0.010" thick. That was not fun to make. I drilled a 1/16th inch hole in some sheet stock, and then by hand and with needle nose pliers turned it into a round washer.
-
Minichamp autopsy for reference... In case anyone needs it...


So I've been meaning to ask, after seeing the small magnetic phillips/can opener combo tool from mini champ/etc used as back side tool on 91mm knife...can the tools from the back of 91mm knives, aside from corkscrew and phillips, but mounted in a mini champ chassis?
That one I haven't explored...
Sent from my iPhone using Tapatalk
-
@hiraethus said:
Syph has put an awl on a 58mm:The other was to have the awl from a 91mm replace the cuticle pusher / ruler layer.
The awl actually fits really well. I filled the original 2.5mm hole with brass and re-drilled a 1/16th inch hole for the right spot for a 58mm hole. In this super up close pic you can see what I mean.




This is just a test setup to see if the awl works and it does. Snap is perfect. The only other thing it needed was a very very did I say very, tiny washer that is 0.010" thick. That was not fun to make. I drilled a 1/16th inch hole in some sheet stock, and then by hand and with needle nose pliers turned it into a round washer.
Nice share...
Sent from my iPhone using Tapatalk
-
Minichamp autopsy for reference... In case anyone needs it...

Sent from my iPhone using Tapatalk
I don't have any, but it's good to have that kind of pic under the hand :)
[emoji482][emoji481]Sent from my iPhone using Tapatalk
-
Some very good info, pics and links there

-
Some scissors I did recently ;)

-
Finally had a moment to finish up this guy. I bought this as an Outrider to get the fine IL phillips for modding into a 91mm knife. It had a chip out of the blade so I just serrated it and removed the chip.
Originally I was gonna put the openers layer in here too, and as somebody mentioned then that's just a Rucksack, which is a standard model. I didn't end up putting them in here thinking it would be a better feel for use as an actual knife. So it's just main blade, WS and corkscrew...not sure what model that is.
Now...here's a question for you 'spurts. You can see I used the thicker (aluminum?) liners on the outsides instead of the thinner liner (nickel silver?) shown in the pic next to the knife.
I did this because when I got it together with the thinner liner on the outside (usually part of the openers layer) with the slight bow/bulge stamped into it, the knife felt too...flexible/fragile I guess.
So I used the thicker one for the outside
There's a thicker one with a cutout in it that I put in the middle (on the Outrider it was between the scissors and openers, but I've seen variants where they used a non-cutout/thick liner in that location.)
I didn't want to put that one on the ouside since there would be nothing to support the scale in the cutout area.So I used the thick one with no cutout for the outside. It works, the saw closes...but what am I actually supposed to use if the saw is on the outside like that and there are no openers?
I suppose the thick liners should be on either side of the blade as they were on the original knife, and maybe I need to fab a thin but flat liner, or additional thick/flat liner for the other side?I'm thinking about putting those openers in there anyway, no big deal re-doing it. I like the feel of this size though. Need a Hercules for the collection.

-
Amazing skills guys..

-
Minichamp autopsy for reference... In case anyone needs it...


So I've been meaning to ask, after seeing the small magnetic phillips/can opener combo tool from mini champ/etc used as back side tool on 91mm knife...can the tools from the back of 91mm knives, aside from corkscrew and phillips, but mounted in a mini champ chassis?
That one I haven't explored...
Sent from my iPhone using Tapatalk
There may be a problem with the hole sizes when the tool is transplanted in "that direction".
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



