Modding Rebar Knifeless?
-
Welcome!
I havent with a knifeless one, but I have with normal Rebars, and they are essentially the same.
What you are going to discover is that assembly is going to be a bit of a puzzle, as the bit holder is not a straight swap for the saw, because it is actually as wide as the Phillip driver. I suspect the most likely reassembly will move the awl to the opposite handle, put the bit driver in the middle, and move the flatheads to the outsides of that handle. The scissors, because of the thumb pad, will need to stay in the same place. This will cause some binding of the pliers during closing, but it is avoidable with careful closing.
Ideally the bit driver would go on the outside (avoiding the binding issue) but im pretty sure that the lock tabs will prevent it from stowing in the handle (this is why the long tools have those triangular cutouts, and why the scissors cant move to the outside.)
-
Oh, and for disassembly, I recommend a set of Leatherman modding wrenches from loki-mobile. They can be found here:
/post/1186359
Sets 1, 2, 3, 4 & 10 will all work for your Rebar. I recommend set 2, as it will allow you to mod any modern Leatherman out there, except the OG Wave and Sideclip (those both need 5 star torx bits, from set 3 and 4).
-
Thanks for your reply! Any tips on the easiest Leatherman to mod to become knifeless and sawless?
-
@hectorlektor said:
Thanks for your reply! Any tips on the easiest Leatherman to mod to become knifeless and sawless?Honestly, a normal Rebar is pretty easy, if you remove the blades and saw there is enough room to add scissors and a bit driver. They are all about the same for ease of modding, although the Wave, Charge and Surge can get a little more involved, as they are more complex tools.
-
Is it possible to buy a "standard" bit driver as the one in the wave as a spare part?
-
loki-mobile might have one for sale: /topic/64314
-
I can get onboard with a modded knife less rebar. Just pair it with a big blade, best of both!
-
Way to jump right in there sLaughtermed
Good link for the wrenches from loki-mobile 
As hiraethus said loki-mobile is a good source of parts as well as those wrenches above

-
Well wouldn't carry a big blade since I don't want to agitate the police :D
Anyway, one thought that hit me is, is it possible to just cut off the saw on the knifeless rebar with a dremeltool or something like that?
-
@hectorlektor said:
Well wouldn't carry a big blade since I don't want to agitate the police :DAnyway, one thought that hit me is, is it possible to just cut off the saw on the knifeless rebar with a dremeltool or something like that?
Well I suppose there is nothing stopping you... you would be missing out on trading that saw for a bit driver though.
-
Well wouldn't carry a big blade since I don't want to agitate the police :D
Anyway, one thought that hit me is, is it possible to just cut off the saw on the knifeless rebar with a dremeltool or something like that?
Well I suppose there is nothing stopping you... you would be missing out on trading that saw for a bit driver though.
Very good point sLmed
I would wait on cutting it just in case you want to trade it 
-
Puh, it feels a litte bit scary to mess with such a nice tool, any tips for modding? :D
-
By the way, I think I settled my mind on a knifeless Rebar and just removing the saw and adding spacers/washers. Anyone got any idea of the size of the washers/spacers needed? Well, more specifically the size of the "bolt" that holds all together?
-
Just check the links above for the wrenches as they are a special made type fastener

Don't know about where you will get washers unless you can get them from another member on here

-
The pivot diameter is 7/16ths I believe. You should be able to find a suitable washer or something close enough at the hardware store. Loki's tools are great but you can get by with good pliers if you are careful. Just be sure to heat up the screw to break the loc-tite. Only one side turns (the side opposite the knife blade), the other is keyed into the handle.
-
@SteveC said:
The pivot diameter is 7/16ths I believe. You should be able to find a suitable washer or something close enough at the hardware store. Loki's tools are great but you can get by with good pliers if you are careful. Just be sure to heat up the screw to break the loc-tite. Only one side turns (the side opposite the knife blade), the other is keyed into the handle.After using Kick clips and pliers for so many years then going to the wrenches and they make everything work so easy
I don't think I could go back to the other way :ahhh :ahhh :ahhh :D But it can be done :D -
I got a replacement Wingman when I sent in my faulty Kick to the Swedish Leatherman rep which handles warranty here i Sweden. So I got some washers and made my old wingman knifeless, works like a charm. To be honest I didn't expected it to be so much fun :D
-
Good deal hector
I like the Wingman personally and I would say it is more user friendly looking than some MTs as well 
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
