Modding Rebar Knifeless?
-
The pivot diameter is 7/16ths I believe. You should be able to find a suitable washer or something close enough at the hardware store. Loki's tools are great but you can get by with good pliers if you are careful. Just be sure to heat up the screw to break the loc-tite. Only one side turns (the side opposite the knife blade), the other is keyed into the handle.
-
@SteveC said:
The pivot diameter is 7/16ths I believe. You should be able to find a suitable washer or something close enough at the hardware store. Loki's tools are great but you can get by with good pliers if you are careful. Just be sure to heat up the screw to break the loc-tite. Only one side turns (the side opposite the knife blade), the other is keyed into the handle.After using Kick clips and pliers for so many years then going to the wrenches and they make everything work so easy
I don't think I could go back to the other way :ahhh :ahhh :ahhh :D But it can be done :D -
I got a replacement Wingman when I sent in my faulty Kick to the Swedish Leatherman rep which handles warranty here i Sweden. So I got some washers and made my old wingman knifeless, works like a charm. To be honest I didn't expected it to be so much fun :D
-
Good deal hector
I like the Wingman personally and I would say it is more user friendly looking than some MTs as well 
-
@hectorlektor said:
Thanks! My name is actually David, Hector is one of my cats :DIt was so fun that Im actually thinking about getting the knifeless rebar and keep modding

Good deal hector
I like the Wingman personally and I would say it is more user friendly looking than some MTs as well 
Sounds good David :D Remember to take pics
We love pics here 
-
So I removed the knife and put in a couple of washers
Not a huge mod, but it all starts small :D
-
@hectorlektor said:
So I removed the knife and put in a couple of washers
Not a huge mod, but it all starts small :D
Good clear closeup pic thanks

-
@hectorlektor said:
I got a replacement Wingman when I sent in my faulty Kick to the Swedish Leatherman rep which handles warranty here i Sweden. So I got some washers and made my old wingman knifeless, works like a charm. To be honest I didn't expected it to be so much fun :DSorry you can't carry a knife around on the daily... I'd be super bummed.
By the way, did they let you know they were going to replace your kick with a wingman prior, or did they just make the decision on their behalf?
-
They didn't tell me, but to be honest it was the wingman i had in mind when i sent it in :)
I got a replacement Wingman when I sent in my faulty Kick to the Swedish Leatherman rep which handles warranty here i Sweden. So I got some washers and made my old wingman knifeless, works like a charm. To be honest I didn't expected it to be so much fun :D
Sorry you can't carry a knife around on the daily... I'd be super bummed.
By the way, did they let you know they were going to replace your kick with a wingman prior, or did they just make the decision on their behalf?
-
I just bought a wrench set from Loki, let's just get a bit driver! :D
@sLaughterMed said:
Oh, and for disassembly, I recommend a set of Leatherman modding wrenches from loki-mobile. They can be found here:/post/1186359
Sets 1, 2, 3, 4 & 10 will all work for your Rebar. I recommend set 2, as it will allow you to mod any modern Leatherman out there, except the OG Wave and Sideclip (those both need 5 star torx bits, from set 3 and 4).
-
@hectorlektor said:
I just bought a wrench set from Loki, let's just get a bit driver! :DOh, and for disassembly, I recommend a set of Leatherman modding wrenches from loki-mobile. They can be found here:
/post/1186359
Sets 1, 2, 3, 4 & 10 will all work for your Rebar. I recommend set 2, as it will allow you to mod any modern Leatherman out there, except the OG Wave and Sideclip (those both need 5 star torx bits, from set 3 and 4).
Cant wait to see what you come up with

-
Im really excited! Ordered a bit holder as well, so now it's the waiting!
-
So I did a little measuring on my Wave and my Rebar. It seems like the measurements are near or identical in handlelenght and so on. The width of the bit holder should just fit if I remove a thin washer. However, will the bit driver lay underneath the pliers when folded? Otherwise it would be hard to fit, but on the other hand it lays under on the wave and therefor fit and the head measurements look like they are the same more or less. Any ideas?
EDIT: Btw it's the knifeless Rebar, but what I understand it's the same as the regular Rebar but blades removed and added scissors.
-
So I finally did it! Got the tools and bit driver from loki today, nice touch with the postcard btw!.
I removed the saw and the fattest of the flatheads and left the thinner flat head there for any light prying needs in the future. Now the knifeless Rebar truly is knifeless! The scissors is still there, but no one cares about a set of tiny scissors, not even the swedish police! I'm very happy with the results and it's awesome! Btw, also removed two micro washers.The bit driver fitted almost as if it was native to the tool!


-
@hectorlektor said:
So I finally did it! Got the tools and bit driver from loki today, nice touch with the postcard btw!.
I removed the saw and the fattest of the flatheads and left the thinner flat head there for any light prying needs in the future. Now the knifeless Rebar truly is knifeless! The scissors is still there, but no one cares about a set of tiny scissors, not even the swedish police! I'm very happy with the results and it's awesome! Btw, also removed two micro washers.The bit driver fitted almost as if it was native to the tool!


Nice work. There's nothing like having a tool that you've made to suit your purposes.

-
Thanks! :)
So I finally did it! Got the tools and bit driver from loki today, nice touch with the postcard btw!.
I removed the saw and the fattest of the flatheads and left the thinner flat head there for any light prying needs in the future. Now the knifeless Rebar truly is knifeless! The scissors is still there, but no one cares about a set of tiny scissors, not even the swedish police! I'm very happy with the results and it's awesome! Btw, also removed two micro washers.The bit driver fitted almost as if it was native to the tool!


Nice work. There's nothing like having a tool that you've made to suit your purposes.

-
Nice job

Although isn't the other side of the Phillips bit a flathead the same size as the small dedicated flathead? Or am I mistaken?
-
Thanks!
Yes you are correct! But, to make everything fit I had to choose one flathead or the other, more for filling space so I chose the smaller one! :)
@sLaughterMed said:
Nice job
Although isn't the other side of the Phillips bit a flathead the same size as the small dedicated flathead? Or am I mistaken?
-
So I finally did it! Got the tools and bit driver from loki today, nice touch with the postcard btw!.
I removed the saw and the fattest of the flatheads and left the thinner flat head there for any light prying needs in the future. Now the knifeless Rebar truly is knifeless! The scissors is still there, but no one cares about a set of tiny scissors, not even the swedish police! I'm very happy with the results and it's awesome! Btw, also removed two micro washers.The bit driver fitted almost as if it was native to the tool!


Nice work. There's nothing like having a tool that you've made to suit your purposes.

Having a tool the way you want it is why I went to the trouble of modding mine as well

Great job and I hope it suits your needs perfectly


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login