Evil's Pocket Octo-Driver: A pen-sized multi-driver kit.....
-
*Hey there, gang. Here is another little project that has been done for quite some time that I never got around to post on (there are many). On any given day, I am always carrying either this, my pocket octo-driver or my Urban Driver for "classy" ocassions. For years I have kept a plastic pocket screwdriver at hand (photos 2&3). It has been cracked and repaired many times over. It has two double ended drivers for a total of four drivers that were only practical for only the smallest of common screws. Of course, not being satisfied with that, I inevitably had to create something to suit my needs: a tool that could accommodate "normal" sized fasteners, a more stout durable tool, a tool that I could expand and use other bits if need be and still be about the size of a pen.....
So, I had this weapon specific tool that I had no practical use for. Made from high grade aircraft aluminum with a nice hard coat anodizing. The tip once had a sight adjustment tool. Stored in the bottom half was a long scraping tool. Wanting a custom pocket driver and having no need for this tool sparked this creation. With the sight tool removed, the bit holder was shortened to a depth of 1/4". The shorter the bit, the more I could store. The long scraper was removed, milled flush, then a cavity was drilled to store one additional bit. The cap was drilled and I installed a carbide tip that I created. Driver bits are chrome vanadium shortened to new length. The end result is a durable bombproof pocket driver with a lot of functionality, all in a package that carries as conveniently as a common pen.....
~ evil ~*
Evil's Pocket Octo-Driver......

On the left, is my octo-driver. On the right is the pocket screwdriver, caps removed, that I used for years. Plastic and limited to 4 mini drivers.....

Comparison shot vs. my old pocket screwdriver with caps installed. As you can see, it is no longer and not much thicker but so much more functionality.....

Here you can see it disassembled. The bottom half houses seven bits, while one stays loaded in the tip. I also often use this to drive various other bits when servicing/creating tools.....

Middle section. Scraper removed, milled flush, drilled to maximize bit storage.....

Carbide tip. Glass breaker/kubotan.....

Size comparison to common pens. On the left, BIC permanent marker. On the right, Sharpie ultra fine tip marker.....

New stubby bit set of the six sizes that I encounter the most. 1/8",3/16",1/4" flat drivers and #0,#1,#2 phillip drivers. Chrome vanadium. On the front row, here you can see the scribe and pen tips that I created.....

*A closer view of scribe and pen. Scribe base is chrome vanadium. Drilled out and carbide tip bonded in and sharpened. Look close enough and you might be able to see where they meet. The groove that you see at the base was made because without it, it was quite a task to remove the bit from the holder with nothing to grab onto. The groove makes for easy removal. The pen, while very small, is actually more than adequate for signatures for packages, quick notes, etc. I tested one until it ran out and I was able to write five full pages of notes before it started to show signs of running dry! I started off with delrin rod stock. Created the hex shape for a friction fit since it is not magnetic, rounded the rest of the body, added a taper at the tip, drilled for mini ink cartridge. I made ten backup pen tips when I first created this. That was some time ago and have only gone through three after considerable use..... *

A closer view of the scribe tip. In actuality, this tip probably gets the most use, though I never want to be without my basic six drivers. Carbide was the only way to go in order to mark some of the metals that I work with. Works wonderfully and has become my go-to scribe.....

Pen tip installed. Quickie demo doodle on notepad.....

-
I hope, in ten years time, I'll be touring the Evil Tool Group factory. Giftshop, coffee, and a talk with the man behind it all.
Nice piece, evil.
-
Love it!

-
@ReamerPunch said:
I hope, in ten years time, I'll be touring the Evil Tool Group factory. Giftshop, coffee, and a talk with the man behind it all.
Nice piece, evil.
That does sound nice
:DAnother great tool and design Evil

-
Absolutely smurfing brilliant! Love the scribe bit. Good work as always Evil.
-
Your artistry, design and build skills are unbelievable. Such talent could improve the lot of the entire society and some tool company should be paying you big time to run everyone else out of business.
-
@ReamerPunch said:
I hope, in ten years time, I'll be touring the Evil Tool Group factory. Giftshop, coffee, and a talk with the man behind it all.
Nice piece, evil.
I will tag along, and spending money in the shop.
-
I hope, in ten years time, I'll be touring the Evil Tool Group factory. Giftshop, coffee, and a talk with the man behind it all.
Nice piece, evil.
I will tag along, and spending money in the shop.
Id make a trip for that. Another great project evil!

-
@ReamerPunch said:
I hope, in ten years time, I'll be touring the Evil Tool Group factory. Giftshop, coffee, and a talk with the man behind it all.
Nice piece, evil.
Thank you, Reamer.....
I would love nothing more than to be able to expand and accomplish that.....Thank you, ddogu.....

I hope, in ten years time, I'll be touring the Evil Tool Group factory. Giftshop, coffee, and a talk with the man behind it all.
Nice piece, evil.
That does sound nice
:DAnother great tool and design Evil

Thank you, Poncho.....
It sounds rather nice to me as well@ducttapetech said:
Absolutely smurfing brilliant! Love the scribe bit. Good work as always Evil.Thank you, ducttapetech.....
I have a knack for misplacing my dedicated scribes. This tools helps me to always have one at hand, much like the scribe on my Style EV1.....@lichan said:
Your artistry, design and build skills are unbelievable. Such talent could improve the lot of the entire society and some tool company should be paying you big time to run everyone else out of business.Thank you for the kind words, lichan. Your comment is somewhat ironic because this particular tool in its unmodified state, was a weapon specific tool, that was sent to me years ago along with a few other weapon specific tools by a company that wanted to branch out into perhaps making more "civilian" friendly versions of their tools. They were sent to me for possible revisions and brainstorming for new tools. I think it would have been a wonderful collaboration because I feel that the build quality on their tools was hands down, better than most any other company out there at the time. This includes all of the major players, like Leatherman, SOG, Gerber, etc. To this day, I still have not seen a better set of needlenose on a multitool. Because of timing, logistics and other factors, things just did not fall into place. I was even to meet with the top dog when I was on a trip to the east coast. Because of circumstances, that fell through as well. I have no idea who runs the company now or if their quality is still the same. The potential was there for them to be a true force to be reckoned with in the multitool world, with me tagging along as the mad scientist behind the scenes.....
I hope, in ten years time, I'll be touring the Evil Tool Group factory. Giftshop, coffee, and a talk with the man behind it all.
Nice piece, evil.
I will tag along, and spending money in the shop.
*And I would do my best to make sure every penny was well worth the build quality, materials, etc..... *
@sLaughterMed said:
Id make a trip for that. Another great project evil!
Thank you, sLaughter.....

-
Pardon me while I drool

-
@ironraven said:
Pardon me while I drool
You are pardoned, lol... I am just kidding. Thank you ironraven, I will take drooling as a high compliment.....

-
You say this started off as an eval copy of an existing tool- the Twist?
I'm getting more and more tempted by that thing if thats the case.
-
@ironraven said:
You say this started off as an eval copy of an existing tool- the Twist?I'm getting more and more tempted by that thing if thats the case.
*Hey there, ironraven. It was sent to me for evaluation by Multitasker. It came with a box (m.i.a) and it did have a name but honestly don't recall it being called the twist. Upon doing a quick Internet search just now all I could find are revisions of this particular tool. I believe this is the first iteration of series 1. Perhaps they changed the name while changing other aspects as well? It's been quite a few years now. I know a few members here are familiar with the brand and have acquired some of their tools and could perhaps chime in and correct or add to this. I see that they indeed made changes. My version had one long scraping tool internally, threaded onto a post within the body. Now I see they have three tools, but now they thread into the bottom end cap instead. Additionally, my evaluation copy did not come with any driver bits, only the sight adjustment bit. I can tell you that the build quality of all of their tools of yesteryear are top notch... and I am very picky about such things. That said, I cannot speak of anything that they've come out with ever since. If memory serves me, this was before the pre-emerson collaboration days. I dealt with one specific individual and have no idea if he is even part of that merger anymore. Anyway, I hope this helps.....
*
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
