Pioneer X problems
-
hmm, so it seems the Pioneer X is a lemon due to a design flaw in the center pin? That's disappointing.
-
@shamus said:
hmm, so it seems the Pioneer X is a lemon due to a design flaw in the center pin? That's disappointing.I forgot to also mention that the snap of it is somewhat dependent on the bent pin to be the right level of snap. When I convert to rigid pivots OMG the snap is way too much like a guillotine. In future I will probably modify the backspring to lessen that.
-
So it all depends on what you get? Whether it's pre bent or straight on what you get? Or does it not matter, it's going to bend and be a crap snapper?
JR -
@MadPlumbarian said:
So it all depends on what you get? Whether it's pre bent or straight on what you get? Or does it not matter, it's going to bend and be a crap snapper?
JRMore than likely. However I have noticed that it's getting better. Less than before. Like Syph said, it depends on where the bend is. If it's bent towards the tool=more snap, away=less snap.
-
So it all depends on what you get? Whether it's pre bent or straight on what you get? Or does it not matter, it's going to bend and be a crap snapper?
JRMore than likely. However I have noticed that it's getting better. Less than before. Like Syph said, it depends on where the bend is. If it's bent towards the tool=more snap, away=less snap.
Ok, knowing my luck if I got one the bend would be so bad the tool would just hang rather then snap.. I'd like to get a new sak, and I've been thinking this one or the EvoGrip thingy, I think a 16
cause it pretty much a tool for tool as my custom, just smaller and not a alox , so in one case perfect but in others sucks.. Can't win..
JR -
@shamus said:
hmm, so it seems the Pioneer X is a lemon due to a design flaw in the center pin? That's disappointing.
Sounds more like an implementation problem, not a design flaw. When are these likely to fail...1 month, 6 months, a year, 5 years, 10 years? Whenever they do fail, won't the Vic warranty will take care of it?Not a lemon, I think the design is sound IMO.
-
@shamus said:
hmm, so it seems the Pioneer X is a lemon due to a design flaw in the center pin? That's disappointing.
Sounds more like an implementation problem, not a design flaw. When are these likely to fail...1 month, 6 months, a year, 5 years, 10 years? Whenever they do fail, won't the Vic warranty will take care of it?Not a lemon, I think the design is sound IMO.

-
@shamus said:
hmm, so it seems the Pioneer X is a lemon due to a design flaw in the center pin? That's disappointing.
Sounds more like an implementation problem, not a design flaw. When are these likely to fail...1 month, 6 months, a year, 5 years, 10 years? Whenever they do fail, won't the Vic warranty will take care of it?Not a lemon, I think the design is sound IMO.
Really depends on where the bend is initially. At the top would be best, because as it would wear it would still have plenty of snap. I think switching to 3mm pins in all would correct this easily. Relatively speaking, less modifications to the tooling at Vic.
-
@shamus said:
hmm, so it seems the Pioneer X is a lemon due to a design flaw in the center pin? That's disappointing.
Sounds more like an implementation problem, not a design flaw. When are these likely to fail...1 month, 6 months, a year, 5 years, 10 years? Whenever they do fail, won't the Vic warranty will take care of it?Not a lemon, I think the design is sound IMO.
Really depends on where the bend is initially. At the top would be best, because as it would wear it would still have plenty of snap. I think switching to 3mm pins in all would correct this easily. Relatively speaking, less modifications to the tooling at Vic.
I think I speak for us all when I say thanks to all you engineering guys that mod and research these problems for us.

-
@shamus said:
hmm, so it seems the Pioneer X is a lemon due to a design flaw in the center pin? That's disappointing.
Sounds more like an implementation problem, not a design flaw. When are these likely to fail...1 month, 6 months, a year, 5 years, 10 years? Whenever they do fail, won't the Vic warranty will take care of it?Not a lemon, I think the design is sound IMO.
Really depends on where the bend is initially. At the top would be best, because as it would wear it would still have plenty of snap. I think switching to 3mm pins in all would correct this easily. Relatively speaking, less modifications to the tooling at Vic.
I think I speak for us all when I say thanks to all you engineering guys that mod and research these problems for us.

AGREED -
So...let's say I wanted to add scissors to my Farmer...as long as I'm using hardened pivots with screws, worst case scenario would be the snap would be too strong? And to reduce snap I would slightly grind the flat surface that mates with the flat sides of the tang on the scissors? Hmmmmm....I may wait and just always carry a compact along with the Alox.
Hopefully Victorinox will address this concern and then triumphantly release the Farmer X with perfect snap and we can all go and buy it in every color!
-
I think this whole issue is overblown. I bought 2 Pioneer Xs and they both had perfect snap. When I disassembled one of them, it did have a bent pin. I wouldn't have even known if I hadn't disassembled it. There have been reports of poor snap, so I guess there were a few that were so bad the snap was affected, but they must be a rarity. It's something that happens during assembly, and I don't feel there's any reason to believe it will get worse over time or fail.
-
It's disappointing. This should not be a problem, and it needs to be fixed. I'm a super fan and all, but I won't sugarcoat the fact that Vic got the design of the Pioneer X wrong.
I don't do mods, so forgive me if I'm wrong, but I think there's a design flaw with the backspring and center pin combo they're using because that center pin gets bent. Either the backspring is too strong or center pin is too weak, I don't know. That's something they'll have to figure out.
-
Any update on this problem, please?

-
One more try, any updates on this problem?

-
I've just been directed tho this thread, and I wonder if the pins are bending on disassembly, rather than assembly. The reason I say this, is that nobody seem to be mentioning any spraining of the liners, also when GigaHz dismantled his, he left the centre pin till last, so that it was fully supported until all stresses were removed. It does sound like the spring is a little over-tensioned though, unless of course there has been further development at the factory since this was highlighted to them .

-
Yes spring is too strong. When I do a conversion with one I have to weaken it. The pin isn't a super tight fit in the spring pivot hole and it definitely bows. Without the bowing the speing would be too strong on stock models too. You could demonstrate but usnf rod stock of stock size but a steel or something that won't bend easy and assmble with that. It will turn into a nail breaker. The first conversion I did the customer sent it back for me to weaken the spring so now I always do.
-
Gotcha. Cheers Bob.
Well if I'm going to have to start grinding backsprings anyway, I might as well do it from a Solo and save a few quid

-
I was thinking about having the opener layer on my PX removed, and Mags kindly offered to do it for me. But I'm getting cold feet now. Any advice? Should I leave it as is? The snap on the scissors is quite strong, stronger than on my Climber and Compact, but not by very much.
-
@Ronald Schröder said:
I was thinking about having the opener layer on my PX removed, and Mags kindly offered to do it for me. But I'm getting cold feet now. Any advice? Should I leave it as is? The snap on the scissors is quite strong, stronger than on my Climber and Compact, but not by very much.Why are you thinking of ditching that layer?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login