Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Washers?

Scheduled Pinned Locked Moved The Mod Squad
5 Posts 1 Posters 941 Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Washers?
Washers?
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • hectorlektor Offline
    hectorlektor
    Posts: 24
    hectorlektor Offline
    hectorlektor
    wrote on last edited by
    Quote Reply

      Is there somewhere where you can get washers that will fit more or less all leathermans? Relativ big inner diameter but relativ small outer diameter, and quite thin would be nice or different thicknesses.

      1 Reply Last reply
      • jcs0001 Offline
        jcs0001
        Posts: 365
        jcs0001 Offline
        jcs0001
        wrote on last edited by
        #1 Quote Reply

          I can't help you as far as sourcing the washers however I would look at making them. You could make different thicknesses out of brass shim stock (sheets of brass that come in different thicknesses from very thin on up). I have an inexpensive punch set (use a hammer with them) and with a bit of care I expect you could make whatever you want. You could use aluminium from beer and pop tins but it would likely gall eventually (become sticky in use). Various industrial supply places should stock the brass and if not you can definitely get it through ebay.

          If you use thin brass you could use scissors to make the outside of the washers but would likely need a punch to make the initial hole.

          Best of Luck,

          John.

          1 Reply Last reply
          • jcs0001 Offline
            jcs0001
            Posts: 365
            jcs0001 Offline
            jcs0001
            wrote on last edited by
            #2 Quote Reply

              I gave this further thought and came up with another idea for making these. Unfortunately I can't locate my brass shim stock or I'd have included a few photos.

              Take two small flat pieces of hardwood or good plywood and sandwich one or more pieces of brass shim stock between them. Drill through the sandwich and create the inside hole for your washers. This is simple and only requires a drill and suitable sized bit - perhaps easier than trying to locate a punch of the proper size.

              Once the inside holes are created use a scissors to cut the outside or get fancy and mount a sandwich of small pieces of plywood on each end and the roughed out washers in the middle - mount them on a bolt, chuck the bolt into a drill (or use a lathe if available) and file them down to size while the drill spins the works.

              Hope this makes some sense. If I find my shim stock I'll put a few photos up.

              John.

              1 Reply Last reply
              • tattoosteve99 Offline
                tattoosteve99
                Posts: 6,326
                tattoosteve99 Offline
                tattoosteve99
                wrote on last edited by
                #3 Quote Reply

                  @jcs0001 said:
                  I gave this further thought and came up with another idea for making these. Unfortunately I can't locate my brass shim stock or I'd have included a few photos.

                  Take two small flat pieces of hardwood or good plywood and sandwich one or more pieces of brass shim stock between them. Drill through the sandwich and create the inside hole for your washers. This is simple and only requires a drill and suitable sized bit - perhaps easier than trying to locate a punch of the proper size.

                  Once the inside holes are created use a scissors to cut the outside or get fancy and mount a sandwich of small pieces of plywood on each end and the roughed out washers in the middle - mount them on a bolt, chuck the bolt into a drill (or use a lathe if available) and file them down to size while the drill spins the works.

                  Hope this makes some sense. If I find my shim stock I'll put a few photos up.

                  John.

                  That's actually a great idea! Thanks for that info

                  1 Reply Last reply
                  • jcs0001 Offline
                    jcs0001
                    Posts: 365
                    jcs0001 Offline
                    jcs0001
                    wrote on last edited by
                    #4 Quote Reply

                      Let me know if it works :D

                      I'm pretty sure it will work and I'll try it once the shim stock reappears.

                      John.

                      1 Reply Last reply

                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                      With your input, this post could be even better 💗

                      Register Login

                      1. Home
                      2. Tool Talk
                      3. The Mod Squad
                      4. Washers?
                      Reply
                      • Reply as topic
                      Log in to reply
                      COMMUNITY LINKS
                      EDC-TV SAKWiki GearFeed SAKSelector
                      Operational Funds

                      Help us keep the Unworkable working!

                      Make A Donation
                      November Goal: $300.00
                      Due Date: Nov 30
                      Total Receipts: $0.00
                      Below Goal: $300.00
                      0% funded
                      • Login

                      • Don't have an account? Register

                      • Login or register to search.
                      • First post
                        Last post
                      0