What did you use your Leatherman for today?
-
Yeah I think I'll give the Space Pen a miss! I looked at some others though - there are quite a few copper pens out there.
-
I had to scratch off Bluetak (the 3M version) that was holding a Porsche 356 miniature replica, drived by Scroodge McDuck (I'm nit kidding). It was installed under my car's windshield for 12-13 years, so part of the material was completely hardened and stuck as a white poweder. I didn't want to scratch the car's plastic. So, after removing the excess with PocketWrench II, the only plastic "scratcher" I found in my EDC was the bottom edge of a Leatherman bit kit holder! It worked perfectly. The car is as good as new. If you need to scratch something delicate and sensitive, I recommend it, over any steel tool you may have.
-
Cutting trimmer line.

Sent from my iPhone using Tapatalk
-
I had to track down why my dryer wasn't hearing up this morning. Turned out to be a thermal cutout fuse I had replaced some time ago. I suspect it was an inferior (or defective) replacement and the dryer ran almost non stop yesterday getting laundry caught up...me and my 2 boys take at least 2 showers a day, plus whatever my wife wears...lots of laundry and I hadn't done any for a few days!
Anyhoo....I needed a few Leatherman boys to get the job done. The medium flat blade on the 300 EOD was used to release the clips holding the front panel on the dryer...the Wave didn't have anything to reach that far!
After that the Wave and my homemade 1/4" bit holder was used to remove and replace all the screws.


Sent from my Nexus 6 using Tapatalk
-
Today like most day,s i did what a cableguy does. Replace walloutlets, cut and strip coax cables and fasten Fconnectors. A day without my chargeTTI is worse than a junk without weed for a week.

-
No pics, but I used my SS ST300 to cut up some smoked sausage for breakfast...that knife is SHARP!!!!
Sent from my Nexus 6 using Tapatalk
-
Cutting an orange for lunch.
-
Repaired a light fixture's bulb holders with the new Rebar. One side was turning on delayed due to some corrosion acting like a delay resistor.
Also, applying some double sided 3M red to hold glide feet to two dining room chairs.
Get use to this tool for a EDC
Sent from my iPhone using Tapatalk
-
To scare the crap out of Milo, my Yorkshire Terrier. I dropped my Surge (in it's leather sheath) on the hearth stone in front of my fire this morning and he was asleep in the chair next to it. He wasn't impressed at all, but enjoyed the few treats I gave him for scaring him.
I was trying to pick up too many things at once and that one slipped. The irony is I'm not carry the surge so put it back anyway, I'm going with the rebar and pioneer to get used to not having the surge on me, ready for the September challenge. I feel kind of naked without the surge on my belt. Though it's nice knowing I have one in my car should I need it's awesomeness :D
-
Minor repairs.
-
Cutting an orange for lunch.
Is that a huge brake disc you're using as a table there?
Yes. It is.
It's looking a bit rough, it could do with a skim.
Or you could see if you can dress the surface with your wave file

Zoom in and look at the cracks. Need some body filler.
-
First use of rebar with bit extension today, to change the batteries in my wireless mouse at work. I don't like the retention of the bit adapter on the philips driver of the rebar. I'm thinking a mod in the future and add the bit exchanger from a wave/surge.
I wonder if Loki has any in stock


-
[quote author=Gohard link=topic=37474.msg1324938#msg1324938 date=1470998870]
Cutting an orange for lunch.Is that a huge brake disc you're using as a table there?
Yes. It is.
It's looking a bit rough, it could do with a skim.
Or you could see if you can dress the surface with your wave file

Zoom in and look at the cracks. Need some body filler.
[/quote]:o That thing is bigger than any disc brake I have ever messed with :ahhh
-
@Kevin Davey said:
First use of rebar with bit extension today, to change the batteries in my wireless mouse at work. I don't like the retention of the bit adapter on the philips driver of the rebar. I'm thinking a mod in the future and add the bit exchanger from a wave/surge.I wonder if Loki has any in stock


I have never had any problems with mine and I have used it for years now
A bit holder would be good for a lot of people though but I like the dedicated Phillips best
Loki usually has stuff like that in stock I would shoot him a OM if you really want one

-
[quote author=Gohard link=topic=37474.msg1324938#msg1324938 date=1470998870]
Cutting an orange for lunch.Is that a huge brake disc you're using as a table there?
Yes. It is.
It's looking a bit rough, it could do with a skim.
Or you could see if you can dress the surface with your wave file

Zoom in and look at the cracks. Need some body filler.
[/quote]I noticed them, but thought there's life in it yet :D
If there is anything like here, they run them till they fail. Which I find surprising considering they are hauling a couple of hundred tons of slag or pig iron around at a time. Needless to say they get right of way everywhere
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login