Help Removing Juice Rivets
-
I haven't tried this on a Leatherman yet, but I've drilled out a couple SAKs. I know there are folks here who have disassembled Juice's before, so you may want to wait from them. But anyway...
Sometimes drilling a small hole down the middle of the pin (hollowing it out) helps give it some room to bend inwards as it's pushed through. Otherwise, try to get a bit as close to the pin size (I want to say it's 1/8 in?) and start drilling down until it budges (after center-punching, being careful not to nick the tools, etc).
-
I know we have some Juice modders in the house so they should be along shortly to help.
In the mean time what sort of mod are you going to do?
-
I'd like to remove the can opener because I never use it and don't like the way it interferes with the scissors. I also have a second S2, so I plan to disassemble that one also, then take the best parts of both and put together a Slim Jim. I already have the pivots and screws. After that, I'm going to look at scale options.
I don't have a drill press, but I do have a hand drill. I tried drilling the rivet, but barely scratched it. I guess I need to pick up a 1/8" bit. What type should I get?
Sent from my SM-N910T using Tapatalk
-
I think I've got a plan now. I bought a set of diamond tip burrs. I'm going to use a small one to drill out the center of the rivet. Think that will work?
Sent from my SM-N910T using Tapatalk
-
Drilling those out are tough. I use a mill, but still the pivots spin. So best way to do it is to cut a slot on one side, so a screwdriver bit can fit it, then hole one side and drill out the other.
-
This would be my choice of tool for disassembling a juice


-
Thanks Steve. I'll give that a try when my bits arrive on the 30th.
Sorry PTRSAK, I'm a Ruger fan! ;-)
Sent from my SM-N910T using Tapatalk
-
The best way to get it out is a punch. Weaken the head as much as you dare slap that sucker in a vice and let the punch drive it out.
-
I tried that and got two of them halfway out, then they got stuck. I don't have a vice, so I'm putting them on a block with a hole under the rivet so it has room to back out. I'm going to try a bigger hammer.
Sent from my SM-N910T using Tapatalk
-
So, I would try coming at it from the other side.
-
That's a good idea. I'll try that.
Sent from my SM-N910T using Tapatalk
-
Hi All. Would like to re-visit this thread.
I ran into a similar situation. I grinded the rivets flat / flush against the scales. I managed to drill down the center of the rivets with a 1.5mm drill bit (I only have this size carbon drill bit with me at the moment). But I still cannot remove the rivets.
Can some-one please advise me how I should proceed to remove the rivets? Thanks in advance !

-
The rivet on one side is thicker. I forgot which side.. If I were u, I will grind off the other end, punch again.
-
Thank you ! I'll try that this weekend and see what happens. You have a great weekend Sam !
-
@Sam Lim said:
The rivet on one side is thicker. I forgot which side.. If I were u, I will grind off the other end, punch again.I finally got the rivets out thank you Sam
! I must have been lucky and picked on the wrong side to grind off in my first attempt 
I can now go ahead and order the pivot screws from Knifekits
. In the meantime, I have re-assembled it with my new configuration with temporary nuts and bolts, minus the springs.My next challenge: how do I put the springs back? Should I install the springs before (or after) installing the tools and pivot screws? Is there a sequence, e.g. tools first, then screws, then springs. Which ones go in first? Thanks again !

-
@Sam Lim said:
The rivet on one side is thicker. I forgot which side.. If I were u, I will grind off the other end, punch again.
I finally got the rivets out thank you Sam
! I must have been lucky and picked on the wrong side to grind off in my first attempt 
I can now go ahead and order the pivot screws from Knifekits
. In the meantime, I have re-assembled it with my new configuration with temporary nuts and bolts, minus the springs.My next challenge: how do I put the springs back? Should I install the springs before (or after) installing the tools and pivot screws? Is there a sequence, e.g. tools first, then screws, then springs. Which ones go in first? Thanks again !
After everything assembled, springs to go in last!
-
@Sam Lim said:
After everything assembled, springs to go in last!
Thanks! May I ask which side of the springs go in first. the pivot end of the scissors, or the empty end?
At the moment you are using screws so the fit is not that tight yet u can try first. It should be easier now. Disclaimer- not responsible if your spring breaks.. Never broke mine before. Pliers, scissors, knife side first. Insert springs all the way in so it's resting on the back of the tools. As far as possible. U should feel some tension. Use a small hammer to tap the other end of the spring. A few taps it should pop in. The springs will try to slip off but u hold them there.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




