Super Stack challenge attempt
-
Some good pics
and you are almost half way there 
-
Day14 Tuesday
New AC filter, this sounds like a job for a SAK screwdriver

-
Day15
Cleaning

-
Day 16 Thursday
There is a story that goes with this frozen pizza. Many of you in the US might remember Taco pizzas in the school cafeteria being one of the better things that they served. Most of those schools or purchasing those from one of Schwan's food service labels. Schwan also owns Red Baron, so the Red Baron Mexican pizza actually tastes just like that favorite for when we were in school.
-
Day 17 Friday
New fence means a stack of old weathered wood for a beauty shot. That is if my photography skills could be called Beauty shots.
The finger is an added bonus.

-
Day18 Saturday
A co-worker of mine brought me a new toy for my collection; A lightly used CRKT Hole-in-One.So what better way to show it than nest to the SAK in today's pic.
This thing had probably the worst bur I have ever seen. It was a complete wire edge that had rolled over. Fortunately it came off with the just a couple passes with a piece of carbide.

-
Day 19 Sunday
Paper towel jam, this sounds like a job for the fish scaler.
Really I just need something pokey enough that wouldnt poke through or cut the rubber band belts inside the machine and had teeth to grip, hook and pull with.
-
I keep missing this thread somehow
Some excellent pics the last few days buddy
Along with some great uses 
-
Day 20 Monday
I posted these comparison pics in another thread a min ago. If it doesnt count let me know and I'll get another post up. Still about 19h left in Monday after all.SAK vs switchblade
/topic/67348



-
Day 21 Tuesday
Another project; this one is a spot finder. I am sure there is a technical term for a protractor sight for doing triangulation but I just call it a spot finder.
The basic idea is that the board has angles marked from the back, in this case in 5deg intervals; a front sight; and two armatures with sights attached to the rear origon point using a pin that acts as a rear sight.
You line up the front and rear sight with an object then without moving the device swing the arms so each lines up from rear sight and arm sight and gives an angle reading. Now you have 3 points of refrence to find where you are standing again.
Coupled with either a range finder or compass and you can make a diecent feature map. The more sight lines you refrence the more accurate you can be.Unfortunately this one is not finished. It still needs front and rear sight pins/screws, and assembled. There are extra lines originated from the front too, these were a mistake that are now just decorative. The last pic is a mock up with some screws I had lying around, but hopefully you get the idea.
I'm using the hook to twist mechanics wire to make the arms. They can be made of anything really, but I had a ton of this thin wire lying around. I remembered how the wire warp holders in the heads of my mother's loom were twisted and thought I'd try it for this.




-
@Noa Isumi said:
Day 21 Tuesday
Another project; this one is a spot finder. I am sure there is a technical term for a protractor sight for doing triangulation but I just call it a spot finder.
The basic idea is that the board has angles marked from the back, in this case in 5deg intervals; a front sight; and two armatures with sights attached to the rear origon point using a pin that acts as a rear sight.
You line up the front and rear sight with an object then without moving the device swing the arms so each lines up from rear sight and arm sight and gives an angle reading. Now you have 3 points of refrence to find where you are standing again.
Coupled with either a range finder or compass and you can make a diecent feature map. The more sight lines you refrence the more accurate you can be.Unfortunately this one is not finished. It still needs front and rear sight pins/screws, and assembled. There are extra lines originated from the front too, these were a mistake that are now just decorative. The last pic is a mock up with some screws I had lying around, but hopefully you get the idea.
I'm using the hook to twist mechanics wire to make the arms. They can be made of anything really, but I had a ton of this thin wire lying around. I remembered how the wire warp holders in the heads of my mother's loom were twisted and thought I'd try it for this.
Very interesting project
Great use of your SAK as well 
-
Day 22 Wednesday
Nothing special.
Just hanging out
-
Day23 Thursday
More brushing dogs with the fish scaler. This time it's Allie;she barely sheds, but she likes the camera a lot more

-
Day 24 Friday
Most people have one tool on a large SAK they just cant find a use for. For many it is the scaler or hook; in my case its the chisel. Almost anything I can think of to do with the chisel can be done with the knife. Mabey I'm just not that imaginative.
So here it is stuck in a bottle of wood glue I was trying to unclog.
Too bad it turned out the glue was no longer fully liquid, and no amount of un-clogging could help it. Good thing I keep an old butter knife hanging around to spread stuff with, so I still got my work done.
-
Day 25 Saturday
These paracord bundles in my EDC bag tend to lossen up over time. The hook is perfect for tightening the wraps without having to completely redo them.
-
Day 26 Sunday
I decided to make myself a new lanyard the problem is I misjudged the length.
the new one hangs at my foot not my knee guess I'll still be using the old one.
Yes my sak is in the photo way at the bottom of my foot that little tiny red dot.edited due to voice type messing up a few words

-
The lanyard in the picture above was made using a simple finger crochet method that I learned as a kid to make garland at the holidays. This is also the same not work that is used for the CRKT quick-release bracelet that I won in the Battleship game.
The only difference between the two is that for garland leave it loose and lacey; when making the lanyard or the bracelet you form each loop, then pull the previous Loop tight locking them all together.
It's a fairly simple knot technique of just passing one Loop through the next and then tightening them down. This will unravel with a quick pull if it is not tied off or if you cut the end off.
Start of this whole knot work is out is by tying a knot in the center point of your line or in this case passing it through a buckle. The buckle in the photos is the eye of a size 1 fishing swivel ,but I didn't like how it was on the line so I cut it off after putting a small link in it's place after lanyard was finished.



-
More pics
Crkt does have a YouTube video available on how to tie this knot included with their quick release bracelet video



-
Day 27 Monday
Painting todayOops forgot the attachment


-
Doing great buddy
You are almost there 
Excellent pics and great uses

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login