What did you use your Sak on today?
-
Spirit? Sak? To much snacks? [emoji1322][emoji100][emoji100][emoji100]
Sent from my iPhone using Tapatalk
Hmmm I think it's just a swisschamp with bigger pliers [emoji38]
Sent from my SM-J500G using Tapatalk

Sent from my iPhone using Tapatalk
-
Classic to trim my beard. Gotta say that now I feel classy
-
Classic to trim something out of my dog's fur and the backstrap Philips head to tighten a piece of trim at home.
-
Alox Rambler, to open several packets I received in the post (knife blade), to cut out an address label for something I needed to post (scissors), and in the evening to change the batteries on the outdoor sensor for a simple "weather station" we have at home, which has a battery compartment secured with small Phillips screws. The Rambler is such a useful little SAK!

-
I used the awl on my Spartan to remove a few staples.
-
Classic 3 times today to open some speed coffee packets :ahhh :ahhh :ahhh !!!
-
@Oxford_Guy said:
Alox Rambler, to open several packets I received in the post (knife blade), to cut out an address label for something I needed to post (scissors), and in the evening to change the batteries on the outdoor sensor for a simple "weather station" we have at home, which has a battery compartment secured with small Phillips screws. The Rambler is such a useful little SAK!
Ooh nice pic! Where can one find a red rambler?
-
Alox Rambler, to open several packets I received in the post (knife blade), to cut out an address label for something I needed to post (scissors), and in the evening to change the batteries on the outdoor sensor for a simple "weather station" we have at home, which has a battery compartment secured with small Phillips screws. The Rambler is such a useful little SAK!

Ooh nice pic! Where can one find a red rambler?
SwissBianco is the only source for alox Ramblers that I know of. Might be worth a try e-mailing, sometimes there are models available that are not on the websites.
-
Bit of Health and Safety work tightening up the treads on the stairs here at work. The SI was more than up for it:
WP_20161006_011 by magpie2112, on Flickr -
@magentus said:
Bit of Health and Safety work tightening up the treads on the stairs here at work. The SI was more than up for it:
WP_20161006_011 by magpie2112, on FlickrCan opener action!

-
Used my Fireman to do some pruning since I accidentally left my shears in a toolshed miles away.
-
@jalind said:
This kitchen cabinet door with Euro style hinges would not close all the way.Efforts to tweak the springs and other adjustments were for naught. Time to replace the hinges. This is a job for the 111mm Work Champ (this one in sterile OD livery)
Upon removing the door and old hinges we find under the lower hinge . . . the installer had broken off a screw head attaching it to the cabinet frame, just left it in place, and drove another at an angle below it.
Good thing the Work Champ has pliers, so we can do what the cabinet installer should have done nearly 20 years ago
We also do with the screws going into the solid oak cabinet frame what the original installer should have done to prevent torquing a screw head off. Just a little bit of bar soap on the screw threads will prevent them from binding in the wood. Acts as a lubricant and as friction heats up the screw, the soap becomes fluid. Amazing how this works!
New hinges were attached to the door, and then the door was mounted to the cabinet frame. It now closes completely as it should.
Some failure analysis on the old hinges to determine why they failed. Turns out the bushing on the lower one that is needed for the spring to keep the door closed had cracked and broken. The piece fell out as I was removing the door, and the analysis showed where it had come from. The screw with missing head may have contributed as it kept the hinge mount from being flush with the door frame, allowing it to rock, but that's a stretch with no real evidence to back it.
John
Great post, John! I learned a little about cabinet hinges! Thanks for taking the time to photograph the process; I know from experience it takes longer when one does that.
One more tip for you: make sure the holes drilled for the hinge screws are the right size. They should be the size of the screw shank, not including the threads. Sometimes, folks drill them smaller, thinking it'll make them hold tighter. Hardwood just doesn't have that much give to it, so it's not a good idea.
-
Ham and eggs for breakfast.


-
-
Ham and eggs for breakfast.
Nice! It's the first time I've seen the slotted Philips in action.

Thanks. To be honest the pliers on my Swisschamp would have been easier then the can key but it worked.
Where's the fun in doing the easier thing? :D You did the MTo thing and that's what's important

-
This year my radiators require venting, DAILY

My Forester in action:
-
nice pic
-
Today was a good day for two reasons. First I saved money and second I recycled. The flusher on our toilet wasn't working properly and I put it down to just old age with wear and tear so I decided to just buy a new one which was around the 20-30 euro mark but before splashing out the cash I decided to give it a shot at fixing it.
Little did I know that it was just the plastic diaphragm that was rip so I found an old plastic envelope to use as a replacement, I used the scissors on my Handyman to cut it piece out and it worked a treat it flushes just like a new toilet.



And a shot of the family for good measures

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login