What did you use your Sak on today?
-
@jalind said:
This kitchen cabinet door with Euro style hinges would not close all the way.Efforts to tweak the springs and other adjustments were for naught. Time to replace the hinges. This is a job for the 111mm Work Champ (this one in sterile OD livery)
Upon removing the door and old hinges we find under the lower hinge . . . the installer had broken off a screw head attaching it to the cabinet frame, just left it in place, and drove another at an angle below it.
Good thing the Work Champ has pliers, so we can do what the cabinet installer should have done nearly 20 years ago
We also do with the screws going into the solid oak cabinet frame what the original installer should have done to prevent torquing a screw head off. Just a little bit of bar soap on the screw threads will prevent them from binding in the wood. Acts as a lubricant and as friction heats up the screw, the soap becomes fluid. Amazing how this works!
New hinges were attached to the door, and then the door was mounted to the cabinet frame. It now closes completely as it should.
Some failure analysis on the old hinges to determine why they failed. Turns out the bushing on the lower one that is needed for the spring to keep the door closed had cracked and broken. The piece fell out as I was removing the door, and the analysis showed where it had come from. The screw with missing head may have contributed as it kept the hinge mount from being flush with the door frame, allowing it to rock, but that's a stretch with no real evidence to back it.
John
Great post, John! I learned a little about cabinet hinges! Thanks for taking the time to photograph the process; I know from experience it takes longer when one does that.
One more tip for you: make sure the holes drilled for the hinge screws are the right size. They should be the size of the screw shank, not including the threads. Sometimes, folks drill them smaller, thinking it'll make them hold tighter. Hardwood just doesn't have that much give to it, so it's not a good idea.
-
Ham and eggs for breakfast.


-
-
Ham and eggs for breakfast.
Nice! It's the first time I've seen the slotted Philips in action.

Thanks. To be honest the pliers on my Swisschamp would have been easier then the can key but it worked.
Where's the fun in doing the easier thing? :D You did the MTo thing and that's what's important

-
This year my radiators require venting, DAILY

My Forester in action:
-
nice pic
-
Today was a good day for two reasons. First I saved money and second I recycled. The flusher on our toilet wasn't working properly and I put it down to just old age with wear and tear so I decided to just buy a new one which was around the 20-30 euro mark but before splashing out the cash I decided to give it a shot at fixing it.
Little did I know that it was just the plastic diaphragm that was rip so I found an old plastic envelope to use as a replacement, I used the scissors on my Handyman to cut it piece out and it worked a treat it flushes just like a new toilet.



And a shot of the family for good measures

-
Nice family you've got there!
I used my Fireman to cut some wildflowers. Pic is in the "Which SAK is getting pocket time today?" thread.
-
@jonon9 said:
Today was a good day for two reasons. First I saved money and second I recycled. The flusher on our toilet wasn't working properly and I put it down to just old age with wear and tear so I decided to just buy a new one which was around the 20-30 euro mark but before splashing out the cash I decided to give it a shot at fixing it.Little did I know that it was just the plastic diaphragm that was rip so I found an old plastic envelope to use as a replacement, I used the scissors on my Handyman to cut it piece out and it worked a treat it flushes just like a new toilet.



And a shot of the family for good measures

Nice job

JR -
I needed the farmers awl to put holes in the ferrets plastic cage to hang and secure things..
JR -
@jaya_man said:
Flashaholics will surely scream at me... Managed to forget taking out batteries on my (retired edc light and kept in drawer for some time) Solitaire LED... caused both the end cap and alkaline to get stuck...Used a mini bench vice and a vice grip to open undo the end cap... sprayed a little wd40 on the leaked alkaline... drilled an entry hole on the battery and used the cork screw of thebYeoman Wood Saw to yank it out...
Cleaned the battery compartment, stuck in a fresh Alkaline... (I know... learn from my mistake and use rechargeables)... tested the Solitaire LED and walaaa... it is still alive...
A good wake-up call to start buying eneloops...

Sent from my iPhone using Tapatalk
I recently began the move to eneloops. One day my flashlights will thank me.
-
Flashaholics will surely scream at me... Managed to forget taking out batteries on my (retired edc light and kept in drawer for some time) Solitaire LED... caused both the end cap and alkaline to get stuck...
Used a mini bench vice and a vice grip to open undo the end cap... sprayed a little wd40 on the leaked alkaline... drilled an entry hole on the battery and used the cork screw of thebYeoman Wood Saw to yank it out...
Cleaned the battery compartment, stuck in a fresh Alkaline... (I know... learn from my mistake and use rechargeables)... tested the Solitaire LED and walaaa... it is still alive...
A good wake-up call to start buying eneloops...

Sent from my iPhone using Tapatalk
I recently began the move to eneloops. One day my flashlights will thank me.
Haven't yet bought my eneloops...

Sent from my iPhone using Tapatalk
-
Flashaholics will surely scream at me... Managed to forget taking out batteries on my (retired edc light and kept in drawer for some time) Solitaire LED... caused both the end cap and alkaline to get stuck...
Used a mini bench vice and a vice grip to open undo the end cap... sprayed a little wd40 on the leaked alkaline... drilled an entry hole on the battery and used the cork screw of thebYeoman Wood Saw to yank it out...
Cleaned the battery compartment, stuck in a fresh Alkaline... (I know... learn from my mistake and use rechargeables)... tested the Solitaire LED and walaaa... it is still alive...
A good wake-up call to start buying eneloops...

Sent from my iPhone using Tapatalk
I recently began the move to eneloops. One day my flashlights will thank me.
Haven't yet bought my eneloops...

Sent from my iPhone using Tapatalk
I keep window shopping for more flashlights.
More batteries vs another flashlight. :ahhh Probably should get me a backup charger as well. -
I used my new Fieldmaster's saw to trim some low hanging branches and the scissors to cut the tag off a new pair of shoes.
-
My Pioneer X was busy tonight. Some friends of ours are expecting their first baby any day now, and we went over to help get their nursery ready. I was hanging shelves and curtain rods. I pryed, drove screws, used the awl to bore out some holes in the drywall, and cut some things. My buddy was sold and is currently shopping for some type of Alox SAK now.
-
Flashaholics will surely scream at me... Managed to forget taking out batteries on my (retired edc light and kept in drawer for some time) Solitaire LED... caused both the end cap and alkaline to get stuck...
Used a mini bench vice and a vice grip to open undo the end cap... sprayed a little wd40 on the leaked alkaline... drilled an entry hole on the battery and used the cork screw of thebYeoman Wood Saw to yank it out...
Cleaned the battery compartment, stuck in a fresh Alkaline... (I know... learn from my mistake and use rechargeables)... tested the Solitaire LED and walaaa... it is still alive...
A good wake-up call to start buying eneloops...

Sent from my iPhone using Tapatalk
I recently began the move to eneloops. One day my flashlights will thank me.
Haven't yet bought my eneloops...

Sent from my iPhone using Tapatalk
I keep window shopping for more flashlights.
More batteries vs another flashlight. :ahhh Probably should get me a backup charger as well.I know...I keep shopping for SAKS, before I know it, there's nothing left of the budget for batteries and charger...

Sent from my iPhone using Tapatalk
-
Used the can opener to open a can of coconut milk, used the plain edged main blade to open a pack of ham and cut up an orange, used the toothpick after eating my ham sandwich, used the backspring Phillips to nip up the screws on the garden gate latch, used the mini driver in the corkscrew to clean some pocket fluff out of the knife, and the day is only halfway through......


-
Used the knife on my Alpineer to:
Open a nicotine patch sachet, open a packet of ham and cheese at breakfast, cut chicken into chunks and chopped vegetables for a lunchtime curry.
I also used the corkscrew to open a nice bottle of Pinot Noir. If I'd wanted a bottle of beer I would have been in trouble (I'm doing the 30-day minimalist carry challenge...)
-
Went to a town social event with a 1980s Spartan, for its slimness. Very boringly used the cap lifter to lift a few caps. And the corkscrew to open some wine. And the tweezers to disarm a thermonuclear grenade that someone had accidentally donated as a raffle prize. Well at least two of those...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login