October 30 day minimalist SAK challenge
-
Argh - wasn't able to post yesterday as I'd accidently left my camera at a party on Saturday and also my phone charging cable, so had no means to take a picture... I did manage to open a bottle of wine with my Alpineer at the party on Saturday, though (and as is probably apparent, drink it!)
Anyway, if I post pics of yesterday's carry and today's later today (after I've retrieved my camera and phone cable), will I still be allowed to remain in the challenge?
-
@GoatDragon said:
Hey guys, I don't think I am going to post a picture here every day for 30 days. Photographing my SAKs is something I only tend to do when the mood strikes. I did it every day for a few days for this challenge, but quickly got bored with the concept. I will however be completing the challenge in spirit, as I intend to carry a single two-layer SAK for the rest of the month, and probably beyond October as well. I tend to carry the same SAK every day, and right now that is my red Cadet. As my possible final photographic submission to this challenge, I present you with my SAK, watch and dog.

Fair enough.
Thanks for submitting your pics so far, GoatDragon. I understand about not wanting to take pics all the time - I've missed the last couple of days too and I'm not sure if I'm going to get a pic for today either. :-\ -
DAY 10
I used the Compact's scissors to open a packet of yeast.

-
@shamus said:
DAY 10I used the Compact's scissors to open a packet of yeast.

That looks delish shamus

-
@Oxford_Guy said:
Anyway, if I post pics of yesterday's carry and today's later today (after I've retrieved my camera and phone cable), will I still be allowed to remain in the challenge?No problems. Just catch up if you can.
-
Day 10
The black Classic with the purple fob should do for today since I will be in a seminar for most of the day.
-
Anyway, if I post pics of yesterday's carry and today's later today (after I've retrieved my camera and phone cable), will I still be allowed to remain in the challenge?
No problems. Just catch up if you can.
Great, thanks!
-
Day 10...
Using my Tinker to open a couple of packs of chicken biscuits, a little snack before I get back to bed. I work nights so I sleep during the day...

Sent from my Nexus 6 using Tapatalk
-
Day 10
Oh, horror! It seems I forgot to post a picture yesterday! I'll post a picture for today but I guess I'm out.
Today I opened some parts got my "new" bike. It's a second hand find with some minor issues that I needed to take care of.

-
-
Oh, horror! It seems I forgot to post a picture yesterday! I'll post a picture for today but I guess I'm out.
Today I opened some parts got my "new" bike. It's a second hand find with some minor issues that I needed to take care of.
If you've got (or can get ;) ;) ) a pic of yesterday's carry then post it up and you'll still be considered for the draw
-
-
T14 Day 10
A grape of wrath with the trusty black and red bantam :)
-
Very good, awl of you. Only 20 days left.
-
10/30 Costco muffins! Or should I say, cake...
-
10/30
I taught my daughter how to use the unique orange,er, Cutie orange peeler.
This gets me current for today. I'm having fun with this!Sent from my SAMSUNG-SM-N900A using Tapatalk
-
Day 10
Oh, horror! It seems I forgot to post a picture yesterday! I'll post a picture for today but I guess I'm out.
Today I opened some parts got my "new" bike. It's a second hand find with some minor issues that I needed to take care of.
If you've got (or can get ;) ;) ) a pic of yesterday's carry then post it up and you'll still be considered for the draw
Thank you!
A very late Day 9
What I use a multitool for the most is without doubt opening stuff and grooming. The soldier works great for most opening but it's rather lacking for grooming so I make do with dedicated tools and have to wait until I get home.

-
<u>Day 06</u>:
(Attempting it ALL single layer!)Got a battery for one of the two locally. Other battery is not as common and had to order it from Amazon. Back to the Watch Opener today for the first watch and probably won't post the second one as it will be yet more of the same . . .
Not using the case knife for this part though! I had left the backs off of both with them laying dial down in a covered tray. They're quartz, not mechanical. Microscopic dust motes are not nearly an issue with them. One is completely electronic digital; no moving parts except the electrons. The toothpick and tweezers aren't on the watch opener just for looks. This one doesn't have a screw down strap over the top of the battery as the other one does; it's a press fit with spring loaded contact along the side and needs to be pulled out. The toothpick can often be used as a wedge if the tip of it can be pushed under the battery, but not as a prying tool as the tip isn't rigid or strong enough for that.

The spacer in this one has a ridge around it very near the battery and cannot get the toothpick under it without bending and damaging it. On to the tweezers, using a corner of one side to pick at the bottom edge of the battery and pull it up. The technique is using just enough force to pull the battery up. Grabbing onto the battery with tweezers and pulling on it is not recommended. Note the copper coil. Getting anywhere near it with anything can break the micro-fine wire (much less than the diameter of hair).

Old battery out, now to get the new one pressed in. Picking up a battery with metal tweezers is highly discouraged as it shorts the battery out and will drain it very quickly (not to mention causing a heat bulge in it). Note where the edge contact is and the side of the battery should be dropped down into the battery well next to it, so that when it's pressed on, the edge will push against the contact. The plastic end of the tweezers is ideal for pressing on the battery, making certain to stay well away from the coil.

A bit of a side note before we put the back on . . .
You've probably noted the very small diameter of the quartz movement compared to the watch case, which is about 40mm diameter, not that large. It's held in position within case by a molded nylon spacer. It could easily fit in a very small diameter woman's watch. This is quite common, especially with very cheap watches. This one is a dirt cheap model, the kind you would find selling for about $10 sitting out in a cheap box on a shelf alongside the costume jewelry, not under glass in a locked jewelry counter. The battery must be quite small to fit into the movement, and that's why these cheap watches only run for about 2 years before the battery dies. By buying the smallest diameter movement they can, the company making them need only use one movement model for all of their watch manufacturing, men's and women's, without having to worry about case diameter for the smallest women's watches. Spacers tend to come in standard sizes and it's the plastic spacer outer diameter that's matched with a watch case. The inner diameter will be the same for all. I didn't get the movement mfr. and caliber number when I opened it up. I'd bet it's a dirt cheap Hattori that cost the watch company well under $5.On with the rest of the show . . . and watch back.
This will use a tool not found on any SAK, or any other "knife" - a case press. I'm showing this to encourage anyone who does their own battery changes in watches with snap-on backs to get one. In the USA, Harbor Freight sells them for $13.99, which is a tiny pittance compared to what you'd pay for one from a professional watchmaker tool company like Bergeon. I cannot begin to recount the amount of frustration I had putting snap-on case backs onto watches before buying this case press. Use one once and you'll never even think about attempting it by hand again. Comes with nylon dies in various diameters. The cupped one goes onto the anvil (bottom) and should be selected so that ONLY the metal watch case around the crystal is supported by its ridge. You don't want to apply any pressure on the crystal, only on the case around it. The upper die is a flat one that should be about the same size as the back, but not larger.
The back will often have a notch on its inner flange for the watch stem. If it does, ensure it's lined up with the stem and remains lined up properly. The watch is placed dial down with the back resting on it (and aligned properly to be pressed on) in the lower die. The press is squeezed with gradually increasing force until the back audibly snaps on, and you're done.

A look at the dial side . . . running just fine and good for another couple years.

Who says the T&T are worthless? BAH!
John
-
@hiraethus said:
I did manage to take a pic today after all. Black and red Pioneer again.

Great pic!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


