October 30 day minimalist SAK challenge
-



Nice shots GF!

-
@Alan K. said:
@shamus said:
DAY 14
I thought I’d try another attempt with the combo tool. If I go slow and easy, I can keep the tool from punching through the cap.

You know that only works for the first 8 or 10 beers. After that, "slow and easy" requires too much effort.
8 or 10?? I would probably pass out and drown in my own vomit.

-
@T14 said:
T14 day 14. What does it have it its pockets, precious?Found a magnifying lens to stick on my old camera. Not too happy about how narrow the focal point becomes.
I reckon the horisontally ribbed alox shields are anodized.DOF in macro-photography is typically quite shallow. Controlling its depth can be a technical challenge. The greater the subject magnification in the image the lens projects onto the focal plane (i.e. film or CCD), the narrower the depth of field. If you moved closer, or had greater magnification from the aux lens you used at the same distance, the DOF would be shallower. Lens aperture also affects it. Larger diameter (lower f-stop number) also narrows DOF, and smaller diameter (higher f-stop number) increases it. Make the aperture diameter too small and it hits the detectable diffraction limit on the optical train's resolving power, creating some detectable fuzziness throughout. If you can control the lens aperture, stop down some but do experiments at f/11 and further for possible diffraction limiting with how you're using the photos. Increasing light for a camera in program mode can sometimes do that but it will also typically increase shutter speed. If you have an aperture or shutter priority mode, you can drive things from there with lighting level, aperture and shutter speed. Another trick is to back up some and crop. Increasing subject distance increases absolute DOF, albeit it also changes subject perspective (i.e. convergence and vanishing point); it's a trade-off. OTOH, the shallow DOF certainly draws attention to the shield logo. Selective focus with a specific DOF can do that if it's the desired result. Ansel Adams, Edward Weston and the rest of Group f/64 demanded complete front to back sharpness (their landscapes in particular), versus Alfred Stieglitz's and Edward Steichen's (et alia of Gallery 291) Pictorialism. It depends on your vision for the final image.
Numerous factors determine DOF and diffraction limits, including if it's full frame or cropped, how large you make the "print" (enlargement) from that, and how close that "print" is viewed. IOW, how it looks in a 1024x768 Photobucket image can be completely different from what it looks like when printed at 8x10" and viewed from 10-12" distance by a human with 20/20 acuity. Ultimately there is also a film grain or digital pixel dimension limit, although I hope these are fine enough that other limits will occur first. Perform experiments to determine how these factors affect the final image as you're going to use it, and develop some heuristics to use when making your photos. Other than your time, digital is free.
I used to make large 8x12", 11x17" and occasionally 16x20" gallery prints from 35mm and 645 medium format film. Had to concern myself with what a photograph would look like in the final print. It gets even more complex with the printing process and its resolution that I won't dive into here. DOF Circle of Confusion, diffraction limiting airy disk, and human acuity at the most likely viewing distance are the big puzzle pieces.
John
-
-




Nice shots GF!





Well done!

John
Thanks guys!

-
Some really great carries and pics today guys

-
Missed posting yesterday,so here's day 13:
Needed to cut the strings and dog hair off of the vacuum roller... Bottom plate screws came out nicely with the pioneers screwdriver/can opener.

-
Day 14
-


And so they're not left out . . .
(;,;)(;,;)(;,;) -
<u>Day 10</u>:
(Attempting it ALL single layer!)The Swisscard, occupying a thin single layer in my wallet, came through today when attempting to open Blu-rays packaged in cellophane, which can be a PITA to unwrap. Many European releases have a pull strip, but more often than not the end of it cannot be accessed with a fingernail, and if it is, it pulls releases from the wrapper and pulls out without opening it:

Using the blade, the easiest place to get started with a slit is where one would open the clamshell as there's a space under the cellophane . . .

Then I use scissors to slice across the front . . .

That's enough to tear it completely off by hand. Now it's finally open and I can watch the movie!


Turns out the other one was wrapped in a polypropylene that could be ripped open by hand. However, just as I was done with this the mail arrived and one item was a small package, so while I had the Swisscard out . . .

Inside were two BNIB 65mm Wenger Esquire, with the vinyl slip cases. I'm beginning to like these more than the 58mm Classic SD as they're slightly larger, but not nearly the size of the 74mm Vics. Scissors and nail file are larger. Vic made a Delemont Executive 81 for a while, which was identical, except with a Vic logo and the Vic T&T, but I suspect it's been discontinued with only the Delemont EvoWood 81 surviving. :-(


John
-
Day 14...
Used the Centurian to pop that cap covering the fitting for lowering the spare tire on my 13 Highlander. Had full size spare on front, put it back under the car.
Getting all new tires tomorrow morning!!!!
Been riding on Bologna skins!!!!



Three of the 4 tires have plugs in them as well!!!
LOL
Sent from my Nexus 6 using Tapatalk
-
Used the Centurian to pop that cap covering the fitting for lowering the spare tire on my 13 Highlander. Had full size spare on front, put it back under the car.
Getting all new tires tomorrow morning!!!!
Been riding on Bologna skins!!!!



Three of the 4 tires have plugs in them as well!!!
LOL
Sent from my Nexus 6 using Tapatalk
Congrats on the new rubber, I have been forced to run Mapops a few times...

-
Used the Centurian to pop that cap covering the fitting for lowering the spare tire on my 13 Highlander. Had full size spare on front, put it back under the car.
Getting all new tires tomorrow morning!!!!
Been riding on Bologna skins!!!!



Three of the 4 tires have plugs in them as well!!!
LOL
Sent from my Nexus 6 using Tapatalk
Minimalist tread for the minimalist thread. I've pushed tires to the "barely legal" a few times in the past myself.
Right time of year in Northern Hemisphere for new tires too - before snow and ice (if you live far enough north for that). I like how the nut releasing the bolt holding the spare is inside the vehicle. Makes it a little tougher to steal the spare. Haven't had a truck or SUV for a very long time so I haven't seen a current design.
John
-
Day 14/30
Ready for fishing with Dad tomorrow. Since he drove, I left my keys at home and just took the Executive, a house key, pill fob, and Olight aaa on my dangler.Breakfast bar for dessert while constructing an attack plan.

Sent from my SAMSUNG-SM-N900A using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


V