October 30 day minimalist SAK challenge
-
Oops, forgot to post my pic yesterday...
Day 15...
Used Centurian to open a package...

Sent from my Nexus 6 using Tapatalk
-
Day 16...

Sent from my Nexus 6 using Tapatalk
-
@m47mu74nt said:
Day 16:
My Micarta Compact freshly re-finishedWait. You have one of these?! That's too cool!

-
Day 16:
Flat lego piece won't come out with fingers.... Awl those darn Legos are so hard to get apart!

-
16/30

-
Day 16:
My Micarta Compact freshly re-finishedWait. You have one of these?! That's too cool!

That's a DIY :)
It is my first Victorinox (yeap, I had the chance to start my "young boy life" with an Opinel n°6 and a Vic Compact), with home made scales from a micarta sheet that I received as a gift in 2014 (a "nearly no-tools" knife making contest I won + GAW)
That scale making was imho much tougher than the 84mm and 58mm Ti scales I made since then! -
@Alan K. said:
Day 16I'm carrying the Alox SD that I received on Friday. It's my first alox SAK. It's so much lighter than a regular classic. The difference has got to be the tooth pick and tweezers. I never gave it much thought, but they must weigh like a ton.
::)It's the tweezers, mostly. I sometimes carry two toothpicks to save weight.
-
Day 16:
My Micarta Compact freshly re-finishedWait. You have one of these?! That's too cool!

That's a DIY :)
It is my first Victorinox (yeap, I had the chance to start my "young boy life" with an Opinel n°6 and a Vic Compact), with home made scales from a micarta sheet that I received as a gift in 2014 (a "nearly no-tools" knife making contest I won + GAW)
That scale making was imho much tougher than the 84mm and 58mm Ti scales I made since then!Awesome. You don't see that often enough ;) very unique my friend! Way to go making it custom, I'm impressed.
-
@kaput said:
Awesome. You don't see that often enough ;) very unique my friend! Way to go making it custom, I'm impressed.That's because you don't see the imperfections through the camera lens xD
I have a second compact (bought it extremely dirty, and I might even need to disassemble the whole to clean it) that is young enough to have the filed hook, but old enough to still have the full width main blade :D
Will it have custom scales? Ti? Wood? or more simple rubis/sapphire/silvertech scales?Hmmm we might finish this in my moding thread instead of hijacking this thread (sorry)
-
@Ronald Schröder said:
@Alan K. said:
Day 16
I'm carrying the Alox SD that I received on Friday. It's my first alox SAK. It's so much lighter than a regular classic. The difference has got to be the tooth pick and tweezers. I never gave it much thought, but they must weigh like a ton.
::)It's the tweezers, mostly. I sometimes carry two toothpicks to save weight.

-
T14 day 16
Old brass liner prince (or cavalier w/o t&t or keyring) today. i really love the nailfile on this thing

I am tempted to swap the blade layer for scissors for an ultimate nail hygiene SAK
Avocado for scale
-Tom
-
Day 16
It's difficult finding good photo opportunities for each day. Here's the Soldier with a background of Harries Tweed that I found second hand a few days ago.

-
DAY 17:
Midnight passed by 7 minutes here,
So my Compact micarta will also be my day17 EDC !
-
Awesome pics last couple of days everyone

-
Agreed. I'm also surprised doing this challenge just how much can be accomplished with a simple one or two layer SAK. A few times I've wanted the smaller pen knife blade, or nail file... But overall for EDC, it sure covers most needs.
Call me impressed, coming from a mainly Leatherman pov.
-
Day 12:
(Attempting it ALL single layer!)A few more photos, not to show the knife as much as how (one method) to cut a small machine screw and have the end threads work well afterward. The machine screws on the pantry door pulls have been about 1/4" (6mm) too long for eons.

Drawer and door pulls have broad heads that are very flat so that they don't dig through the wood or stand proud from the back. They're also typically a combination Phillips and flat tip so the installer, who would invariably have the wrong tipped driver in hand, doesn't have to go back to his toolbox for the proper one. Because of the desirable head profile, it's better to reuse the screws whenever possible than try to get new ones from the hardware store. I'm going to cut about 1/4" off these and reuse them. In the effort long ago to get these to pull the handle flush, they were tightened by someone else using a power driver. The 3-D Phillips on the Apprentice can take the torque to get them loose.

Once loose, I can spin them out using the flat-tip. :)

Once both screws are out, the next step is cutting them down. No tool on any SAK can do this very effectively. The metal saw on a Craftsman or Champion Plus could be used, but that's still much less than ideal and it requires holding the screw to make the cut which is difficult at best without damaging threads (been there, done that, with hack saw and vise). For small machine screws I have this nifty Waldom hardened steel wire stripper and lug crimper that also has a machine screw shear for small numbered screws. These are #8 with National Coarse thread pitch (32 tpi). Thought at first it might be #10 National Extra Fine (also 32 tpi) but they were too loose in the #10x32 hole.

Get about 1/4" protruding from the other side and it's ready to be sheared off.

A bit of a squeeze and the end of the screw is nipped off as nice as you please. Much easier than using nuts, a vise and a hack saw!

Experience has taught me it's a good idea to chamfer the end of the screw before chasing its threads and backing it out of the tool. This metal hand file was handy (I'd been using it for other tasks recently). A grinder also can be used, and I've used one on large bolts cut with a hacksaw, but care must be taken not to overheat the screw. Don't need a grinder for a soft steel screw this small.

With the end chamfered, I chase the threads by working the screw end back and forth through the threads in the cutting tool. Chasing the threads is why you always put a nut onto a screw or bolt, or a thread cutting die, if not using a threaded cutting tool. Backing it out is much easier than trying to get it started just after being cut. The Apprentice's Phillips is ideal for this.

Once both screws were shortened, I put them all the way into the handle to see if they would thread easily, and to check against the door edge to ensure they were sufficiently shorter, which turned out to be just barely, but that's OK. Just barely short enough works.

They now tighten up flush on the back side, with the Phillips ideal for giving them some torque to keep from coming loose.

And the handle is now flush and tight on the front side!


A better look at the (several decades old) Waldom crimping tool with the Apprentice fabricated earlier this year from a Waiter and "thrashed beyond all recognition" Tinker. Waldom still makes this tool, which speaks volumes about its utility. The Apprentice is a Cellidor Bantam with backside Phillips. Perhaps that's why it was discontinued, as it was between a Bantam and a Small Tinker with the other two proving more popular. Could have just shown the Apprentice in use, but thought showing how the screws were shortened would be helpful for anyone who hasn't done it before.

John
-
That Waldom crimper is fantastic!

Thanks for Sharing, John
-T -
16/30
Switching from the Executive back to the Classic for work tomorrow.I fileted the catfish, thought about trying a SAK, but the fish were too big. I used a dedicated filet knife (USA Schrade)

Sent from my SAMSUNG-SM-N900A using Tapatalk
-
Day 17:
BantamRambler for the office today:
-
Day 16
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login